Having problems with your Vacuums ?

Beater bar won't work on Dyson DC21 - Vacuums


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Beater bar won't work on Dyson DC21 - Vacuums


... Vacuums

I was vacuuming with my DC28 Animal and all fo a sudden the beater bar stopped working and NONE of the floor mode buttons work.. no lights or anyhting. I checked for obstructions per the Dyson manua


... Dyson DC28 Animal Bagless Upright Vacuum

Terrible noise My dyson was working great then started making this horrible noise. I cleaned the bar but noise is still there. I discovered the beater bar went around three passes then froze and started horrible noise again. my husband got the bar turning but after 2 swipes vacuuming it did it again. Can it be fixed or is it time to retire it and buy a new one. Wendy Kiser


That noise is the clutch. A very expensive part and very hard to replace. When a problem with the clutch happens it's generally not worth the time and money to replace.I suggest getting a different type of vacuum, maybe a Miele or Sebo. W ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

BEATER BAR QUIT WORKING ON DYSON DC07 VACUUM CLEANER - DIDN'T KNOW IF THERE WAS A RE-SET SWITCH OR HOW TO GET THIS TO WORK AGAIN


Hi its Darran at Dyson. From your description of the problem, either the brush control has been switched off (dial on the side of the cleanerhead) or the belt has snapped which may indicate a problem with the clutch. Please ca ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson animal beater bar not working - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Is the belt ok that drives it , is the clutch ok this video will give you instructions how to fix ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson dc21 beater bar on dc21 stops working during use


... Dyson DC21 All Floors Stowaway HEPA Bagless Canister Vacuum - Iron/Titanium/Yellow

Beater bar dyson vacuum Works intermittently - Vacuums


... Vacuums

Beater bar not working. suction not working - Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum


Check for a broken beater brush belt.\015\012Clean the beater brush, clear of all debris and add some WD40 at each end where the rubber holders are. Turn beater brush by hand to work the WD40 into the axle.\015\012Reassemble making sure the belt is ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Dyson vacum beater bar does not work - Dyson DC14 Bagless Upright Cyclonic Vacuum


DC14 have two drive ... Dyson DC14 Bagless Upright Cyclonic Vacuum

I have a DC25 that I just bought in Dec 10. The last few times I vacuumed the carpet, the beater bar worked on and off. Now it does not move at all. I took off the beater bar to see if there were any obstructions, but there were none. Could you please help me with this. Right now my husband is saying that we should not have bought such an expensive vacuum (which he has said all along). I want to prove him wrong!! Up til a couple of weeks ago, it was working perfectly and I have loved it!


This is a good quality machine which I am sure wil last a long time in answer to your question make sure that the setting is set for carpet and not just flooring ..the head needs to be flat on the floor for the beater to work .I am assuming that thi ... Dyson DC25 All Floors Bagless Upright Vacuum

Dyson vacuum beater bar takes a while to start working.


Hi there, \015\012SmartAlec from NelsonVacuums.com.au here. If there are no bad sounds or smells when you are engaging the bar then it is a sign that your belts are s ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The beater bar doesn't work - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


You need to replace the belts. Here are the belts you need:Dyson DC14 Belts ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

What is wrong when beater bar is not working - Dyson Ball DC24 Bagless Upright Vacuum


... Dyson Ball DC24 Bagless Upright Vacuum

Beater bar won't work - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The beater bar quick working. - Dyson Vacuums


Remove the bottom plate and take out the beater bar plus the drive belt. Inspect the drive belt for burn marks or other damage. The bar itself is usually bound up at the bearings on each end with string, hair, and thread. Pull the bearings off, then ... Dyson Vacuums

My Dyson DC17 beater bar motor works intermittedly. I have to almost whack it on the floor to turn it on and then shuts off again. I have checked the belt and it is fine, also have checked for blockages. The switch to turn the beater bar on or off will not work when the beater bar motor is off. the suction is fine though.


Buy a Kenmore for less money ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My beater bar on my Kenmore 116.25615506 canister vacuum keeps turning on and off when I vacuum rugs. The suction continues, but the beater bar seems to be shorting or whatever. I checked the belts and they look like new. Any suggestions? The rest of the vacuum works fine!


... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have a dyson DC28 vacuum and the power button flashes on and off and the beater bar quit turning. I turned it over and found some string caught on the beater bar which I removed, but the beater bar still does'nt turn and the power button still flashes on and off. I hope you can give me a solution to this problem.


I had the same symptom with my wife's DC28. The problem was associated with the cam driven height adjustment mechanism. The beater bar must rock freely up and down when pressing on the tabs that the end cam lobes actuate. On ours I found hair and cru ... Dyson DC28 Animal Bagless Upright Vacuum

My dyson animal is hard to push on carpet - the beater bar is still operational. When I turn off the beater bar and run the vacuum on hardwood the beater bar stops moving, but it still ''rolls'' on the hardwood - it doesn't pull up like it used to. It also seems to not be picking up as well as it used to, although no blockages are present and the filter is clean.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The beater bar on my Dyson won't turn. The vacuum runs and suctions but the bar won't turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won't turn


The belt doesn't have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won't operate the way it is supposed to. You can get replacement Dyson Belts here: ... Vacuums

Dyson dc41 beater bar not working


... Dyson Dc 41 Ball

My beater bar does not work on my vacuum. The problem is not in the hose or the attachment, because I connected to another electrolux vacuum and it worked. So the problem must be in the canister.


It's most likely a loose wire in the canister then. I recommend taking the whole vacuum to an Aerus Electrolux store and letting the service tech check it out. They can find out the problem quickly.\015\012Be aware they may try to sell you a ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Have a dyson vacum and the beater bar stopped working. How do you fix the beater bar.


Hi its Darran at Dyson.Check that the brush control dial is in the centre position when upright and then moves forward when the head is released. If the brush bar is still not spinning when switched on in the vacuuming position, check th ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0968 seconds