Having problems with your Vacuums ?

Rug doctor brush not working

\015 The brush under Neath is not scrubbing\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Rug doctor brush not working


... Vacuums

BRUSH NOT WORKING ON RUG DOCTOR MIGHTY PRO


Watch this help video there are on you tube! ... Rug Doctor Vacuums

Rug doctor new rug doctor. Vacuun works. Sprayer does not work. What should I do?


... Vacuums

My Rainbow SE vacuum was working fine until I ran over the edge of a rug and it went in to the nozzle. I immediately switched the vacuum off and proceeded to move the rug. When I tried to turn the Rainbow back on the brush was no longer spinning. I've tried the reset button and checking the nozzle for any debris, there are none. The brush just won't spin.


Hello lilbutmunch1,\015\012The brush is motor/belt driven so you probably either broke the belt or it shifted off the motor or brush shaft. I suggest you unplug it,flip it over and look for screws that hold the baseplate together.. remove those ... Rainbow E series Canister Wet/Dry Vacuum

We have a kenmore canister vacuum and it runs but when turn on the rug clener brush the brush will not run we then put on small brush head and that will work


If the power head motor runs, but the brush doesn't turn, then the belt is broken. Replace the belt and it should work. ... Kenmore Vacuums

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu


This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

My shark bagless sweeper worked for about 6 months. Like a previous blogger, I caught the edge of a rug that jammed the sweeper, three red lights blink, the brush is free moving yet the sweeper will not work. I did leave it plugged in all the time otherwise it would not run but for minutes. Very disappointed. New battery? what if that doesn't work? is it junk then, money down the drain.


This will probably cost you more to repair than to buy a new one. Does it turn on at all? ... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

Replace a brush motor on rug doctor


... Rug Doctor Brush Drive Motor Kit

The brushed roller on my Hoover Upright Canister has quit turning. Is this a broken belt? A friend recommended a "reset" button--is there such a thing?? Everything else works fine; power, suction, headlight. That belt just doesn't work anymore since we accidentally caugght the edge of a throw rug.


Belt. There is no reset on this model. ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

The motor that powers the brush the brush that beats the rug has a sparking in it ( it works but this does not appear good)


You will see sparks all the time around the brushs if it is working and if the sparks do not go all the around the comutaor\015\012it will be fine ... Fantom Vacums Lighting Canister Vacuum

Rug brush bar does not work


... Dyson Ball DC24 Bagless Upright Vacuum

I HAVE A BISSELL 12AMPS PROHEAT2X RUG SHAMPOO, IT WON'T PUMP OUT WATER TO CLEAN ,THE BRUSHES WORK BUT NOT ANY LIQUID. ALSO CAN YOU GIVE ME A REPAIR SERVICE NEAR THE 34219 ZIP CODE


You have to stop leaving the cleaning solution the tank after you're done...unfortunately you may be outaluck...try putting a tiny amount of ammonia in the tank and keep pulling the solution "trigger"...maybe you'll get lucky...otherwise trash the va ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Bissell rug cleaner belts and brushes not working


Click on the link below for instructions ... Vacuums

I have a Rug Doctor ez-1 that the vacuum only works through the upholstery tool and not underneath. The underneath vacuum only blows air outward. I have switched the carpet/upholstery switch depending on what function I'm using but still no suction on the floor. Any ideas?


... Vacuums

My Oreck XL was working fine, then when I vacuumed a shag rug is started smoking and smelled like something is burning. (I changed the bag, checked for clogs--none found, and roller brush is turning. It has a metal handle.) Now I am afraid to use it.


Even though the brush is spinning, the belt is probably worn out and stretched. when you vacuum the shag carpet, it puts more drag on the brush. try running it on a shorter carpet or hard floor for a few minutes. if it doesn't smoke, then you know i ... Oreck XL2000 Bagged Upright Vacuum

Rug doctor hand tool will not spray ...but it will vaccum....what can I do to get the hand tool to spray again ....tried another hand tool and that didn't work either ....help


... Vacuums

The brush does not rotate for cleaning rugs.


Have you tried pusing in the little red buton on the side of the brushes cos if thats out they wont work ... Dyson Ball DC24 Bagless Upright Vacuum

Brushes only work when Dust Bin is removed!! I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'


HI, If the brushes work , without the bin, the problem , the problem could be caused , due the failure at the bin lock mechanism. There is a sensor that checks if the BIN is connected properly or not. This problem is best resolved by getting ... iRobot Roomba 560 Robotic Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

MY WIFE BOUGHT THIS FOR ME FOR FATHERS DAY GIFT ABOUT ALMOST 2 YEARS NOW OR SO,BUT I HAVE THIS PROBLEM THAT THE BRUSH DOS'NT SPIN ANYMORE EVERYTIME I PUT THE SWITCH ON FOR BRUSH ON,THE HOSES BRUSH SPIN IS WORKING BUT FOR THE FLOOR CARPET BRUSH SPIN IS NOT WORKING,AND THIS IS THE MODEL NUMBER OF MY HOOVER VACUUM CARPET SHAMPOO CLEANER IT'S F7411-900


This unit uses a turbine assy to turn the brushes. The brushes could have something jamming them. Remove the brush unit, it is held on 2 spring hooks 1 on each side. The brush unit is driven thru a 1/4" square post, only one brush is driven and it dr ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My Roomba only works correctly when I leave out the rubbery type brush (not the fiber filled brush)...... when I leave the rubber one in, it doesn't pick up & then finally stops & says REMOVED BRUSHES..... I have cleaned every nook & cranny of this thing... inside & out. I finally found that if this one brush is left off.... it works great & has for 2 weeks??? What could be the problem?


Hi,\015\012First let’s try one more time to clear out anything that might be caught inside. For this disassemble the green brush cage unit, partially, from the blue box. This would expose the cover of the gear box. On t ... iRobot Roomba 560 Robotic Vacuum

I have a miele S4210 vacuum. It has a SAB100 accu nova battery brush which will not work. After charging the battery, light comes on saying not charged and now the power head brush won't turn. I had problems with my first powerhead so I purchased another and it worked for a short time and now I have the same problem again. I have four batteries I use interchangeably but nothing seems to work. I spent a fortune on this vacuum and to tell you the truth I hate it! Contacted Miele after 1st year of


... Miele S300 Bagged Canister Vacuum

How do i get the brushes to work again on my steam vac it all works other than the brushes ....the brushes wont spin


The scrub brushes won't spin on my Hoover F5915-900. ... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

Hi, I have not owned my electrolux pronto 2 in 1 for very long but the roller brush has stopped turning. The handheld part works and the green light is on. I have done a thorough cleaning of the roller brush and all other removable parts. What might be causing the roller brush to not work? Thanks, Jen


Check the end cap bearings ... and replace the belt even though it may not be broken. Put a drop of sewing machine oil (no more) in each end cap bearing. ... Electrolux EL1000A2 Pronto Bagless Stick Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0563 seconds