Having problems with your Vacuums ?

Vaccum wont work

\015 I have a eureka boss 4d.\302\240 The suction works, but the motor that turns the belt is not working, any suggestions\015

Answers :

There is also a reset button on the side at the bottom. Good luck.
On mine, the motor wont turn on, but the belt turns. i found out that it is the power switch, but your best bet is to go to a vacuum repair business and order the part. (if it is under a year old it should be covered under warrenty).
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Vaccum wont work

There is also a reset button on the side at the bottom. Good luck. ... Vacuums

Roller brush bar wont turn after te machine made a popping noise then just only the vaccum is now working

I had this exact problem after moving the machine by car. after opening the machine there is some dampness so suspect popping was caused by liquid mixing with electricity. The machine does have drain holes so leave it upright for a week or two and t ... Bissell 9200 Upright Vacuum


Check the belt, and remove any objects clogged in the roller system ... Dyson Vacuums

My Brother XL4030 wont swtich from bobbin winding to sewing - bobbin winding works but when i switch to sewing just wont work

... Vacuums

Rainbow vaccum I have a rainbow vaccum and it stopped working. The on and off switch may not be working. I am not sure how to change that switch?

Make sure the bowl has the pin on it. The Vacuum has switch in the bottom that keeps the Vacuum from running if the bowl in not on or the little pin is broken off. \015\012\015\012 \015\012\015\012Ralph Wakeman\015\012\015\0 ... Rainbow 75th Anniversary Canister Vacuum

Pickup water wont pickup the water after putting it down very little comes up into the tank .it worked fine when we baught it but after not useing it for some time it worked now it wont **** water up at all can anybody help.

The clear shroud covering the front of "hood" has two sheet metal type screws at the bottom in front of the brushes, these two screws also hold the little straight brushes ( one on each side) in place. I found one of these screws had broken it's plas ... Hoover F6020-900 SteamVac Upright Vacuum

Hello, I have a Hoover 3200 Turbo Power vaccum. while the motor appears to be working fine the vaccum no longer picks up the dirt. I turned the vaccum upside down and the belt appears to be broken. would a broken belt stop the pick up, there appears to be no suction. This vaccum is approximately 10 years old. is it worth fixing? I live in Virginia Beach Va, where would I take the vaccum for repair? my zip code is 23456- Thanks Cleta Goode

... Hoover Vacuums

Vaccum problem I turn the vaccum on and it does not run but the light on the vaccum works. Bissell bagless vaccum cleaner

No sound at all? or the motor runs but no vaccuum?\015\012did it stop while using it? might have overheated due to dirty filters... strange that the light comes on but no motor at all... that would suggest to me that the motor is shot... ... Bissell 6594 PowerForce Bagless Upright Vacuum

DC07 brush wont spin on bottom, took all apart and wont work

Hithe belt is broken or stretched, replace it ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a kenmore vaccum i changed the power cord for the powermate and still not working the model # 11652512202 it work for a second then stop working

Could be your off/on switch ... Kenmore 28614 Canister Vacuum

Electrolux oxy 3 vaccum has stppoed working and all three blue lights flashing My electrolux oxy 3 ZO6330 stopped working suddenly and all lights are flashing. I've changed the bag and filter and its still not working. Any ideas??

... Electrolux Vacuums


Inside the clipers there is a spring switch,,its broken? or all the vibration in the clipers has shook a wire off inside,,,in short its time for a new set of clipers,, ... Vacuums

My bissell vacuum attachments wont work, as soon as i attach anything besides the crevice tool it wont ****,but sucks fine when its just the hose

Tern upside down remove plastic cuvier look wear the hose gos fillip skew driver ... Bissell 6594 PowerForce Bagless Upright Vacuum

Rotating bruch My vaccum brush will not turn. This happened after sucking up a cord that wrapped arou8nd the brush. I was able to pull the cord back out but now the brush will not turn. The vaccum does turn on an sounds like it is working with no soinning brush.

Take off the bottom cover where the roller brush is a few screws should be all it takes underneath cover should be roller and belt if belt is broke replace it lift up roller there is a slot for the belt to run in put other end should be the motor sid ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have a eureka altima bagless and it wont pick up dirt i clean it and everything it just wont work

The belt is probably worn, stretched or broken that is why it is not picking up. Here is\015\012a link to the owners manual which has instructions and a link to the\015\012belt you need. ... Eureka Capture Upright Vacuum Vacuum

Help!!!! i have an older model of the dirt devil bagless quick vac. and it has been working great, just last week i was vaccuming my bedroom and i accidentally sucked up a string belt that goes with one of my capris. and today i emtpied out the dirt cup but it seems the the string belt that was sucked up is not within my reach and whenever i start the vaccum i get this distinctive noise that i've never heard before. help.

It's likely wrapped around the brush\015\012pull out the roller and un tangle it ... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

When I was using my Bissell ProHeat 7901, I smelled something hot (almost burnt) and turned off the vaccum. When I turned it back on, everything seemed to be working, but the vaccum part was not making the same sound. The bristles are still turning, but it isn't picking up as much and is leaving quite a bit of lint on the carpet. Could the belts be worn? How do I tell? Thanks!

Ya that is probably the issue. Here is a link to the belts you need and to the manual which has instructions:Bissell ProHeat Belts and M ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My dyson works with the hose but wont work the normal way

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

WST 1600A I purchased this vaccum about four months ago from Heartland America. Up to this point it's worked fine. After cleaning it this time when I went to start vaccuming again it runa for about 10 seconds and cuts off. I've changed the battery, taken everything that can be removed out checked it and replaced it. THe motor sounds like it's straining. I have not taken the housing off the motor to see what's going on with that. I misplaced my manual.

It sounds like there is a clog. If there is no air flow it could be overheating. ... Westinghouse WST1600 Upright Vacuum

How do i get the brushes to work again on my steam vac it all works other than the brushes ....the brushes wont spin

The scrub brushes won't spin on my Hoover F5915-900. ... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

Hoover F7431-900 my carpet shampooer/steam vac was working fine until the brushes at the bottom of it just miraculously stopped working. they wont spin at all. Is this a motor problem? perhaps a water flow problem? please write back if you can be of any help. thanks

If the screen is not dirty, and the flapper valve to the turbine inlet is open, then the problem is mostly a stuck turbine impeller. The turbine impeller on my F7431-900 has seized TWICE!! The shaft for the turbine is not made of stainless steel, t ... Hoover F7431-900 SteamVac Vacuum

KARCHEN 5500 My vaccum has 6 years old and the problem is that it does not work properly (wet vaccuming process). From the model overview I need Carpet turbo nozzle and the water filter. My email is [email protected] Thank you very much Patricia Perdomo 786-2620411

... Karcher K DS 5500 Vacuum

Re UH70040W seriesZF12.0.I can't seem to get the brushroll agitater to work it just stays off and the brushroll does'nt work the belt that drives it wont grip the roll? It's brand new!

I followed the instructions,you have to release the handle as though you were vacuuming and it works automaticly you can't put it on ON when it's upright!! Duh ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My suction wont work. It works for about 2 swipes and then quits. When you stop and restart it does the same. It is only 2 months old!!!!!

Hopefully you don't have a bad impeller on the suction motor. Start with this though: Make sure that you check for obstructions in ALL of the tubes, from the brushes all the way to the bag/canister. I've found that in many cases, especially if you ha ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Scuncii Steamer wont work wont blow steam anymore

It is probably clogged with rust or limescale - can happen with steam cleaners. Sadly there's no way around this but to try a limescale remover in distilled water such as Calgon limescale remover. Fill the kettle as normal and give it time to boil up ... Scunci 52067 Handheld Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0711 seconds