Having problems with your Vacuums ?

Parts replacement We have a Hoover Steam Vac that has a broken part #10 in your picture or Part # 37271035. Does this part cover the whole top section of the Vac? Is it hard to replace? Where can you get the best prices on Hoover parts? I have been on Hoovers website and they don't even recognize this Steam Vac. which is hard to believe they don't even recognize their own unit? Thanks Ray


Answers :

This the hood or top cover. There some screws on the bottom as well as on the top, then it comes off.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Parts replacement We have a Hoover Steam Vac that has a broken part #10 in your picture or Part # 37271035. Does this part cover the whole top section of the Vac? Is it hard to replace? Where can you get the best prices on Hoover parts? I have been on Hoovers website and they don't even recognize this Steam Vac. which is hard to believe they don't even recognize their own unit? Thanks Ray


This the hood or top cover. There some screws on the bottom as well as on the top, then it comes off. ... Vacuums

Beater brushes not turning on the wife's Hoover Steam Vac model F5905-900. Found one prior ''solution'' stating that it sounded like the belt was bad. That was my original thought, but on checking schematics and trying to find part numbers at Sears Parts Direct and at Hoover, it does not appear the F5905-900 steam vac HAS any belts to begin with. What's next??


This one I can tell you about from personal experience with that generation Hoover Steam Vac. After using it about 7 or 8 times my brushes stopped turning also.I disassembled it (kind of like disassembling a Chinese puzzle box) and found ... Hoover F5905-900 Vacuum

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

I don't know how to use my hoover steam vac on carpets, hard wood floor, my (tile floor), my upholstery. I'm spraying and yet I don't see no suctions on neither of them. do you have a how to do step by step video that I can use in order to get the maximum result from my hoover steam vac.


Here is a link to the User Manual, in case that will hekp:\015\012\015\012http://www.hoover.com/pdfs/manuals/F5914900.pdf ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I am looking for a Hoover Steam Vac Bare Floor Attachment, Part #90001331. I found one in the US for $8.95 but by the time I paid shipping and handling it would cost $91.77, a little ridiculous. I am looking for one in Canada. Can you help. I have heard Hoover has been bought out and parts are very difficult to purchase. I bought this 1 month ago and I'm sorry I didn't know this prior to purchasing.


Hoover Bare Floor Attachment F5XXX from Usavacuum.comIt is $6.99 and shipping should cost you le ... Hoover F5906-900 Upright Steam Vacuum

I have a Hoover Steam Vac. Even though I don't


There in the trigger assembly is a release button that might be broken. ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

I own a Hoover Steam Vac V2 deep cleaner with Auto Rinse feature. The Model Number is not available ex: was on the bottom of the machine and the sticker is completely worn off the machine. I am having a problem with the bottle you fill with detergent ex: this bottle is seperate from the main clean water tank. THE PROBLEM: The little plastic part that goes in the bottom of the bottle has an "O" ring ex: cone shaped with a spring.....it keeps falling out. Can you supply a part number for this


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=641300\015\012Generic problem for all Vacuums\015\012I own a Hoover Steam\015\012Posted by w_brennan on ... Vacuums

I just purchased the hoover steam vac model F5853-900 from a garage sale and everything seems to be working well except i dont see any steam coming out from anywhere and the water in the vacuum stays cold. is there supposed to actually be a steamer inside this vacuum? if so, is there a button i need to turn on for the steamer to work? thank you so much for the help!


... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

We are putting our Hoover steam vac F7425-900 back together again after getting a new turbine assmbly part. However, we have a part ( #38454-013) that we are unsure where it fits. Can you assist us?


... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Hoover F5809 Hello, I seen a few of your post and was hoping you could help me. I just became a member today. My sister gave me her old Hoover Steam Vac-Model F5809. This thing is so dirty and clogged because my sister has pets. So far I've gotten it all taken apart to clean it. I'm not a newbie and taking apart and fixing things. I have fixed things like microwaves, washers, dryers, dishwashers (still learning about TV's-very hard, hehe). Anyway, I got what I believe to be the motor cover off.


That cover is the called the fan cover and is usually pressed on. Tapping on the edge with a flat blade, you may be able to get it off and hope you don't bend it up, you will to put it back on tight enough so it will stay in place. Another thing to ... Vacuums

I have a hoover f5861-900 steam vac. the trigger mechanism seem to not work anymore. Water dribbles out without using the trigger. Taking the water tank out I can see the rod very slightly moving on the diaphragm. I removed the top part of the vac to hopefully reset the rod connection. But, didn't make any difference. I appreciate any help you can give me. thanks


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hoover Steam Vac Dual Tank Bottom Valve Spring Assembly Part Needed


It appears that there is a problem with the o-ring design. The o-ring should maintain a certain OD dimension and keep the spring assembly from pulling throught the hole. I am trying to find the service manual to locate the o-ring part number but hav ... Hoover F7431-900 SteamVac Vacuum

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest


I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

I have a Hoover Steam Vac All Terran floor shampooer, I have taken apart the brushes and other parts to make sure there are no clogs, but it still is not spinning. What else can I do? the Motor is working fine. and the suction is fine too.


There may be some substances such as dust or sand stuck in the spinning parts of the wheel. The substances are restricting the mechanism to work properly and causing blockage in the rotating causing your problem. Cleaning every part of the motor's ro ... Vacuums

The Hoover steam vac dual v does not spin its brushes and I dont know how to dismantel it to view the belt .


There is no belt on the steam vac - it operates on air flow. Remove the brush and insert a flat screwdriver into the square hole. If it does not turn, the turbine has seized up and must be replaced. Remember that the brush will not turn unless the lo ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Hoover Steam vac has also stopped sucking... I have pulled it apart to clean it. Is there a way to take the bristles off to clean them as well as are there any other parts that could be the problem?


Based on your description, poor suction is related to only a few things\015\012\015\012Check filter inside lower tank\015\012Check the lower tank lid to be on properly\015\012 ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover steam vac model f5912-900 stoppped sucking.please dont tell me to check the hose, there isnt one,and the extraction tank IS empty.this machine is brand new with 10 minutes on it ?????


There is a hose under or behind the extractor tank which can come loose or tear. Lower the handle and remove the tank to look for it. See if it sucks when you use the upholstery attachment. If it does this would indicate that the part that lowers to ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Hoover STeam Vac Dual V. Replaced the water tank-no problem. but water still pours out through the bottom. when idle, when off, when running. dont need to press the lever. Help!


Te dual V models have an electric pump and 2 solenoids that control the soap and water to dispense. The problem you describe, sounds like the water solenoid is stuck open. and would need to be serviced by a repair shop. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My hoover steam vac is leaking. the water seems to come out where it should by the brushes but it all leaks out even when not depressing the button. seems to be suctioning fine.


The problem you describe is a bad resevoir. I have replaced a few in this model series. Take it to an authorized dealer for repair. ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

HOOVER STEAM VAC. I CAN ATTACH THE SOFA CLEANER ATTACHMENT AND THE SOAP WILL COME OUT BUT I CANNOT FIGURE WHERE TO ATTACH THE ROUND PART THAT WILL **** THE SOAP BACK UP


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

HOW DO YOU TAKE A PART AND REPLACE THE BRUSHES ON THE HOOVER STEAM VAC F5858-900


HI There,\015\012\015\012Here's a repair that I did that explains step by step on how you can remove and replace the brushes on your Hoover SteamVac, I hope this is helpful to you. If you have any questions, please feel free to use the c ... Hoover F5858-910 SteamVac Vacuum

Broken hose The hose on my Hoover F5837-900 Steam vac Supreme broke away from the coupler on the bottom of the unit - under/behind the recovery tank (solution tube is till attached). It might have gotten pinched in there a couple times. Problem - it was glued in the coupler really well, and I cannot get the whole thing out - hose will be too short anyway - is there a way to fix this or a part I can order instead??


You will have to replace the complete hose asm, part # 90001337 ... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

My 5 green brushes dont go around on my steam vac from hoover


Can you spin your brushes by hand? if not you have a bad turbine. if you can clean the lint trap under the small clear window in the front of your steamer. ... Hoover Vacuums

Brushes dont spin on Hoover Steam Vac Model F5919-900


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hoover steam vac won't suction water. It will with the hand tool, but not the main part. I feel hot air blowing out of the bottom.


... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0927 seconds