Having problems with your Vacuums ?

Nutone central vacuum shuts off after a few minutes running then will restart after motor cools down I cheked motor and vent ports blown out all clean


Answers :

Sounds like you have an overtemp switch that is tripping and shutting your motor off. Many motors use what they call a 'snap switch" ( looks like a small disk with two wires on it ) to sense motor temp and if that trips, then it will temporarily disable power to the motor until it cools down enough to allow power to be reapplied. If you are sure everything is clean and your motor can rotate freely ( if there is a restriction that limits motor rotation, more current is drawn to drive the motor thru that restriction ..which in turn will cause excessive heat build up and the temp switch to trip) ... Hope that helps!
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Nutone central vacuum shuts off after a few minutes running then will restart after motor cools down I cheked motor and vent ports blown out all clean


Sounds like you have an overtemp switch that is tripping and shutting your motor off. Many motors use what they call a 'snap switch" ( looks like a small disk with two wires on it ) to sense motor temp and if that trips, then it will temporarily disa ... Vacuums

I was vacuuming the vent in the bottom of the fridge. I must have picked something because the motor got wildly noisey. I cleaned out hoses, etc. There is no suction. I can see the blades of the motor and they are not turning around. Model U4269-930 Series B.72. Can I get at the motor to see if something is keeping the blades from turning? What would be your suggestion. Many thanks. Pat Sauerman


Hi Pat, my name is John I will do my best to assist you.\015\012\015\012You certainly can get at the motor, with simple hand tools. \015\012\015\012Referring to this ... Hoover Vacuums

Eurika Whirlwind vacuum cleaner. Nearly new. Suddenly lost succion.l I cleaned and dried the filter. It developed an odor, then stopped short. I believe the motor may be burned out. Motor is cool, but it won't start. Is there a fuse??t


Look around the nozzle it might have a reset switch ... Eureka WhirlWind Litespeed 5844 Upright Vacuum

My dyson animal just cuts out mid vacuming ,the motor gets quiet hot ,and wont start again for an hour or so when i expect the motor cools down .all filters cleaned no blockages etc.. any suggestions?????


This is a feature so that the motor does not burn up check all tubes ... Vacuums

Kenmore Progressive cannister electric motor will not operate. Is there a fuse blown or some other reason? All filters are clean. Power works to wand only.


Apparently there may be a fuse in the canister itself, I have no instructions for getting to it though. There's another post on here you might want to check, perhaps that person can tell you how to get to it\015\012\015\012 ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I was given a model 6591, plugged it in and it worked but didnt "****" and didnt sound right. I turned it off and removed the hose from the back found a badly plugged hose. Removed the hair plug cleaned filters and when I tried to turn it on again. Now the motor will not turn on or even make a noise. I hear there is a fuse that can be blown? How can I find the fuse if there is one? Thank You Ron


The User Guide for the bissell Clearview Power Trak\012\012http://canada.bissell.com/images/UserGuides/3590C.pdf\012 ... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum

My bissell aroma pro had a horrible burning smell then stoped sucking up water. the motor was still working and water was being feed out just not back up. the machine was hot as i had already cleaned 3 rooms in the house. i let it cool down but the burning prob returned as soon as i turned it back on. any help would be great thanks


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

I have a nearly 9 year old Electrolux Excellio Z5228 vacuum cleaner. It has recently started cutting out during operation. I cleaned the micro filter (between bag & motor) via brush & hitting against wall & seems / looks quite clean. I washed the gore filter (output from motor to clean the exhaust air) as per instructions, then let to dry. It was very clogged but now very clean. The vacuum clearner still cuts out often. Even after a long rest (say overnight) it still won't start, then ano


... Electrolux Vacuums

There is no power...seems like a motor problem. The bag is clean...the mouth is clean the plug us in...NOTHING! I took mouth off and manipulated/pushed in that power press area that engages the motor on the front (not the switch on the back) and NOTHING! Not sure if motor died and/or what to do now. Help. I have had this baby for 15 years.


The front safety switch must be pushed in by either the hose or head (or manually), before the on/off switch will operate. The most common reason for no power is a bad cord. Second most common is worn carbons in the motor, and third is a bad switch. ... Kirby G4 Bagged Upright Vacuum

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb


Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

DYson DC07 not sucking properly when in upright mode. I have tried cleaning out pipes etc and even tried an old motor section I had in garage (replaced once under warranty as kept cutting out and they left old motor section here). Even the old motor section had same prob so this suggests its something in the rest of the vacuum cleaner (whats left after you have lifted off the green motor section and dust collection area if you see what I mean? Any advice weclome please.


Blocked filters ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Bad Motor? I have an upright Electrolux Prolux Heavy Duty "Appareil Industriel" and the motor does not seem to be working and turning the brush. Is there a trip switch somewhere to try and reset the motor? I have taken the plastic cover off on the base of the unit and cleaned it well, but can't seem to get the motor to start again.


... Electrolux Vacuums

I was just using my Bosch 1450W bagged vacuum and all of a sudden, the motor just shut down. No warning, no problems. The light still turns on, but the motor is unresponsive. There is a clean bag and filter, and nothing caught in the front roller. The motor sounded fine - no shaking, or weird frequency variations. There were no weird smells, just a little bit of heat, but nothing beyond normal. I've had this thing for several years, and never had a bit of trouble with it. Any suggestions


Many vacuums have internal thermal switches that need to cool to allow the vac to operate. After 30 minutes, check all 3 air filters and try again.\012Gary ... Bosch BSG71310UC Bagged Canister Vacuum

Clarke Instructions helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? t


... Vacuums

I removed the filter from the motor in the ball. After I cleaned it and let it dry, I put it back in. From then on, it makes a moaning noise when I turn it off after I vacuum. I followed directions to clean it and put it back (it's pretty straight forward and fool proof). I've since cleaned the filter a second time, doing the same steps and it seems to have made it worse.


... Dyson DC25 All Floors Bagless Upright Vacuum

Clarke scrubbers helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? ther


... Clarke Vacuums

IRobot rumba 4000 seems to run ok and then starts making a kinda hi pitched growling noise and slows way down. it is very clean(blown clean with air compressor)sensors are clear ,newly installed well lubricated on ends of brush and beater bar, new battery. it seems like the wheel tracks may be dragging . i have cleaned and lubricated where i could on them but can't find a way to totally remove and inspect wheel tracks.


It sounds like your Roomba's brush gears are not working. Run the robot without the dust bin to see if the brushes are turning. If they are not, the robot will need to be replaced. Contact iRobot CS for support at (877) 855-8593. ... iRobot Roomba 4000 Bagless Robotic Vacuum

My 20" Patton electric fan has stopped working. I use it for animal cooling and it operates in dusty conditions. I suspect that the motor is shot. Is it worthwhile to replace the motor and are motors even available?


You could just try to clean the motor out by taking it apart, and shining the shaft up. then put some motor oil/engine oil on the shaft. That will work 99% of the time. ... Vacuums

Hoover Jet and Wash 1500w S6254 001. Used once with great difficulty as assembly and use instructions are hard to follow.Now will not work as carpet shampooer at all, although assembly is correct as far as I can see and both motor and pump appear to be working and I am using the recommended cleaning fluid.Hoover website is no use at all in solving the problem.No cleaning fluid is being drawn up from the tank in to the cleaning fluid hose.There is suction from the suction hose so the problem appe


I am having the same prob my uncle got me one i cant find the manual anywhere to set it up the prob i have is where does the handle to make the water go out connect tooo ??? on the main pipe that sucks it back up i have tried every which way but not ... Vacuums

I cleaned out my dyson ball as it smelt when i hoovered, cleaned filters, washed out canister and took the screws out of the front bar so i could clean near the brushes.. now its making a high pitched noise and when i switch it off it makes a noise like an engine shutting down! Have i disturbed the motor?


Hi its Darran at Dyson. The screws on the base of the cleaner head should not have to be removed to access the brush bar so it is possible that the brush bar has come out of alignment, hence the noise the machnie is making. Pl ... Dyson Ball DC24 Bagless Upright Vacuum

How do I access the motor to my eureka capture? It has no suction at all but turns on just fine..filters are cleaned and there are no clogs or leaks on the hose....im thinking there must be something stuck in the motor possibly but there are soo many screws that im having trouble removing them all....whats the best way to access the motor to check it??


... Eureka Capture Upright Vacuum Vacuum

Ok. i have a bissell proheat 2x model # 8920 06356c i'm trying to clean a large rug in my home .. i have the fluid in the tank and can't figure out why it's not cleaning as it should.. the motor's running but not spraying and cleaning as i expected to do..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

My Air Vac is 20-21 years old. Recently it stopped running. I found the fuse by the motor was blown and replaced it. It blew immedicately when I turned it on. I think I need to repace the motor. Do you agree and can I buy a motor from you.?


If the fuse does keep blowing yes you do need to replace the motor. I am sorry we do not sell parts though. Try the link below to get the motor.\015\012\015\012 ... M&S Systems Vacuums

I have a bissell 1698 powersteamer. i have already cleaned heater and completely cleaned all parts , checked the mix piston, checked belt. it will not shoot water or mix. the motor runs, it will **** water and the brush turns. is it the pump and does the pump just shoot the soap?


Pump is probably bad. When you put the lid back down, did you put the piston on the bottom of the smart mix knob? Also the smart mix knob should be in the water only selection when the top is pushed all of the way down. Also sometimes the flow ind ... Vacuums

Dust....dust....dust Hello, I recently bought a house with an older Electrolux Central Vac system. I'm unfamiliar with them, so I'm not sure how to deal with this: I cleaned up some mortar dust with it, and noticed not too long after that when I went into the garage, there was a fog of dust. The hose from the unit is venting into the garage. Is this normal? I have since used it for everyday household cleaning and each time I go back to the garage to a cloud of dust. Is there anything I can


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=113662&thid=662824\015\012Dust....dust....dust\015\012Posted by Kitkatman on Jun 11, 2008\015\012Hello,I re ... Electrolux Central Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0592 seconds