Having problems with your Vacuums ?

My brand new dyson d18 wand is clipped into the body of the machin but will not release. Help?


Answers :

I am sure you figured this out by now, but in case others out there are having the same problem. It is really simple. You have to pull the stick, the wand out of the handle all the way. THen it will just come off itself. The instructions are NOT clear, so don't feel dumb!
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My brand new dyson d18 wand is clipped into the body of the machin but will not release. Help?


I am sure you figured this out by now, but in case others out there are having the same problem. It is really simple. You have to pull the stick, the wand out of the handle all the way. THen it will just come off itself. The instructions are NOT clea ... Vacuums

The rotating brush on my Dyson DC25 wont go round - can you help - the machine is new but I don't have the manual?


... Dyson DC25 All Floors Bagless Upright Vacuum

The hand held dyson does not appear to charge. does the battery come away from the unit as I can't seem to release it? Would there be any point in buying a new battery as I don't know if this is the problem. The red light stays lit all the time it is on charge and when I take it off the machine does not respond at all.


The battery is located at the bottom of the handle. To release it, press and hold down the button on top of the battery case (it has 3 ridges on it). That releases a catch and you can then slide the battery out to the rear. This can be quite ha ... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

This is embarassing, but I have just looked at the Dyson DC07 manual and at my Dyson for about 20 minutes, and I can't for the life of me find the wand release button on my actual Dyson.....the manual pictures don't look like the parts on my Dyson....I don't have a hose with a wand release button....the hose just goes straight up inside the handle....Can someone help me? Thanks :)


Hi the wand release button is located directly above the the Cylinder release button. The wand release button looks like the picture below. In order to releease the wand you must firstly make sure the Electrical cable is not wrapped up for storage. S ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Dyson DC17 has lost suction on the wand and is not picking up dirt as it should. I have taken the small part at bottom of the machine off to see if there is a blockage--none that I can see. The flexible tube on wand is very tight and won't extend very much. Dyson sent me a new cyclonic part in April but the machine still doesn't seem to be working properly. My serial number is 260-us-d11545. Is there somewhere I can take my Dyson to get it fixed. I'm very frustrated with it. Thank you.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Top thread does not pick up bobbin thread, also clicking sound when needle is down under plate, as if it is hitting something. Please help I have a job to do! This machine is new it's a Singer Inspiration Model 4228. It worked just fine until I finished my first sewing job on this machine. I'm hoping you can help me! Thank you, CD


... Singer Vacuums

I just got a new machine (new to me anyway) new home hf106 model. i need to thread the bobbin on the new thead i am using and am not sure where to put the empty bobbin and how to thread it. help!


Janome New Home? Unfortunately, Janome doesn't put the manuals for older machines on their website. Your best bet is to contact your local Janome sewing machine dealer and ask for a "copy" of the manual from them. A photo copy should b ... Vacuums

I have a dyson alergy machine, I have emptied it, but I would like to clean the filter. I can't locate where the filter is or how to get to it to clean it. The manuel for this is not with the machine. This machine came with the house we live in. Could you help me please? Laurie


Greetings Irlawren3, \015\012\015\012It all depends on the model you currently have. The filters on some are above the motor and some are on the side housing. Its pretty clear looking at the unit where the filters are located. I would su ... Vacuums

I got my Mom's Kenmore sewing machine and I an trying to figure out how to get the scalloping and arrow head stitches to work. I have followed the manual and I can get all the other stiches but those two. It is a Model 1451 zig zag machine. I realize it is old, but the machine is just like new. HELP. Thank You.


... Vacuums

I have a dyson DC07. The hose has come away from the hose end and the end is stuck in the top end of the wand as it sits in the upright position on the machine. Any ideas as how to get it out? If I can get it out it might just be a new hose. If not, it's a new hose and wand.t


... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

My Ultralux 2000 vacuum power head does not work on my machine but does work on a different machine. What are the possilbe problems? I tried replacing the hose with a new one and that didn't help.


It's probably due to bad wiring connections between the wands, hose and wand, or power nozzle and wand. If it came with the Sidekick, try using it on the end of the hose. If not, simply try using the power nozzle on the end of the hose (no wands). ... Electrolux Eureka Easy Clean 2 in 1 Stick and Handheld Vacuum Model 108A 1 ea

Hi. We've got a Dyson DC17 "Animal". It's clogged, and we are unable to separate the purple cyclone cap from the main cyclone body to get to the problem. We've heard of 4 torx screws that take some interesting tactics to access. I've been through this thing with a flashlight, and torx tools for a protracted period, and even after removing the torx screws was unable to ultimately separate the two pieces (main body from purple cap assembly). Any help would be greatly appreciated. Thanx -


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hello! Help!! The brushbar on my dyson ball vaccuum will not spin. I took out the brushbar and cleaned it, then reset and cleaned out the filters too but still doesn't work. Do you think I need a new rectifier? Thanks for your help.


Sorry this is not a solution. But after reading your problem and other people with the same problem, i just wanted to say i have a Dyson DC24 ball and have only had it 1 year and the exact same thing has happend it is spotless inside and out includin ... Dyson Ball DC24 Bagless Upright Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work


It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

I have the Aerus Lux7000-My full bag light indicater is coming on even with a new bag. It gets worst-the machine will cut off when I insert the hose or put my hand over the hole where the hose goes. I changed the filter on the back and put in a new bag. Help please :)


Hi, you very likely have a defective control valve under the dial on top of\015\012the vac , or a kink or blockage in the tiny pressure hose that feeds\015\012the air from the throat of the vac or the back of the bag chamber\015\012against the two si ... Electrolux Guardian Bagged Canister Vacuum

I have the dyson dc07 all floors and have a new belt- I have removed the black cover but cannot see where to attach the new belt ! Hope you can help-Carole


Hi there Carole, VacuumGuru here. \015\012I have made a video on how to access the ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson dc17 hose will not come out/ handle wont release from machine. i've pulled the metal rod up all the way and the handle still won't come away from the machine so i can't use the hose and attachments. anyone know what the problem might be?


Hi there, it is possible that you have a blockage in the wand/hose assembly which is making this difficult to remove. If you are able to remove it to check for this, please contact our Helpline on 1866MYDYSON so that one of our advisors c ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Help hi there. i have a hoover savvy u8172-900 vaccum. the hose has great suction, but there is limited suction on the main unit and the brush does not spin when i try to use the product. we have cleared the brush of any debris and have also installed a new bag. a few days ago, we disconnected the hose to make sure there was not any foreign bodies stuck in the unit...nothing seems to help. any advise?


As the hose fits into the base (if i am correct) the power at the base should be fine, make sure the base is clean and free from blockage,\015\012you say the brush doesn't spin, has the belt broken, if so replace it, (very cheap) and only a couple of ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

I have taken delivery of a new Lloytron Halogen Oven E4701 WH.from a supplier in the UK (I live in Spain). On unpacking it I found that Part of the temperature control knob assembly had fallen down inside of the heater body. I dismantled the heater body to retrieve the part but I cannot now work out the order of re-assembling the fan parts so that the fan does not catch on other parts of the assembly. I cannot find a parts drawing on-line. Can you help ?


... Vacuums

I require to purchase secondhand or new - in New Zealand a part for Dyson DC01 Cleaner. Part needed Yellow bin catch! Can anyone help


Managed to get one locally and glued mine until it arrives\015\012Adie ... Vacuums

I have the electrolux guardian-My full bag light indicater is coming on even with a new bag. It gets worst-the machine will cut off when I insert the hose or put my hand over the hole where the hose goes. I changed the filter on the back and put in a new bag. Help please :)


Hi,\015\012Check your hose you have something stuck in the hose...stretch it out straight and run something through it to push out whatever is stuck in there...\015\012\015\012heatman101 ... Electrolux Guardian Bagged Canister Vacuum

The solution stick inside the handle needs replaced and I would like a new face plate. I have the model numbers (38458-031 & 37275-011), but can not locate the replacement parts. This machine is more than 10 years old and works like brand new. I can not see throwing it out and want to fix it. Please help me locate these parts. Thank you!


... Hoover Steamvac F5860-900 Vacuum

NO POWER My Dyson DCO4 Absolute (purple&lime) won't' switch on. I've checked the plug fuse, wall socket and also filters and hoses on machine all seem fine so think the problem is with the on/off button (maybe loose wire or something) but how do i get to it, is there a special way to remove the green on/off button in order to check the connection? Thankyou in advance for the help i am sure you will be able to provide.


The problem is almost certainly a fatigue break in the flex. These usually happen where the flex enters the handle through the rubber sleeve near the on off switch. You will need to cut about four inches off the wire and reconnect it to the switch. ... Vacuums

Not spraying The machin e is new and i use it a few days ago, we cleaned it inside and out, it is not spraying any cleaner or water. Can you help me?


• tanks are not sealed into receivers• faulty auto load receiver• pinched/clogged line• defective component allowing air into system• pump not mounted so it can move freely• defective bridge ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0975 seconds