Having problems with your Vacuums ?

How to change belt on kenmore progressive 37100

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I can't seem to get the belt cover off of my Kenmore Progressive 400. There are two buttons that say above "belt and bulb change" but the buttons do not move. Do you know how I can remove so I can put a new belt on? Thank you!

You have to take off the top of the power nozzel that has the light lense. There are two pressure locks,one on each side. Use a screw driver to release. You will see the screws.Take the two screws out and on some models, there are two pressure locks ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

My question earlier today referred to a Kenmore Progressive upright vacuum. Your answer suggested that I change a belt, if the reset button did not work. Does a direct drive really have a belt? Regards, Jim Buckley

Direct drive does not have a belt. It is a shaft with gears. What is wrong with your vaccum? Maby i can help. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

I've got a Kenmore canister vacuum, Progressive 236123, and there's a burning smell from the belt side of the head--smells a lot like hot rubber. I've cleaned the agitator and changed the belt, but I still get the smell. It's stronger when I'm using "carpet" mode than when I'm using "bare floor" mode. Any ideas what the problem is?

... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

How to change belt Kenmore Progressive 300?

... Oreck XL2200 Bagged Upright Vacuum

How do I change the belt on my Sears vacuum? - Kenmore 25512/ 25513 Progressive Canister Vacuum

Hello,Here's what you'll need to replace a belt on a Kenmore ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I need to change a belt on my kenmore progressive 360 canister vacuum.

... Kenmore Vacuums

My Kenmore Progressive keeps burning up belts even after I have changed the bag, cleaned the filters and checked to make sure the agitator was clean and free turning

On the left hand side, just above the handle release, is a lever to adjust if you are doing hard wood or carpet cleaning. When adjusted for hard wood, that lever releases the belt and just uses the "vacuum" function. When set for carpet it engages ... Kenmore Vacuums

How to change a belt on a kenmore progressive vacuum

... Kenmore Vacuums

How to change the belt on the kenmore progressive glide vacuum cleaner

... Kenmore Progressive Glide Upright Vacuum Cleaner

How to change belt on kenmore progressive 37100

Try this linkhttp://www.managemylife.com/mmh/owner_manuals/6827/KENMORE-Vacuum-Upright-L0403213 ... Vacuums

HOW TO CHANGE A BELT - Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Hi there...You will need a Phillips screwdriver to get the bottom cover off.Remove the screws and then remove the bottom cover.Clean out any excess dirt in the general area of the roller bar and motor assembly area.Place one end of the belt over the ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Dirt is coming out the bottom of my Kenmore Progressive Upright Vacuum. My husband found a large dust bunny in the drive belt and removed it. He also changed the bag. Why is dirt coming out the bottom? Thanks.

Its still clogged, you gotta dig deeper ... Vacuums

I just inherited a Kenmore Progressive vacuum cleaner with direct drive and HEPA filter. Can't figure out how to change the belt - don't have a manual. Thanks. Jo-Anne

Http://www.managemylife.com/mmh/owner_manuals/6826/KENMORE-Vacuum-Upright-L0403208 ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

How to change the belt for kenmore heavy duty plus extra wide sweep model no. is 1163966180 looking for manual how to change the belt

... Vacuums

Need to replace belt on my Kenmore Progressive Vacuum Model # 116

HiOn your products manual is the replacement procedure.www.managemylife.com/mmh/lis_pdf/OWNM/L0311026.pdf ... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t

The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

Lever & belt placement in Kenmore Progressive upright vacuum

You are correct. The belt is supposed to go around the peg that is connected to the lever so that when it is on the Floor /Tools setting the belt is not driven by the drive shaft. ... Kenmore Vacuums

How do i change my Kenmore upright vacuum belt?

... Kenmore 33721 Upright Vacuum

Kenmore progressive model 38812790 smelled like rubber burning then the brushes stopped turning. Does it have a belt, if so, how do I get to broken belt to replace?

... Kenmore Vacuums

How to change filter in kenmore vacuum - Kenmore Progressive Upright Vacuum with InteliClean System Slate Blue

... Kenmore Progressive Upright Vacuum with InteliClean System Slate Blue

Need tp replace belt on Kenmore CB-3 - Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

I have a kenmore vacuum cleaner that I bought a new belt for butcannot get the bottom off to change the belt. Model # 116 53312305

... Kenmore Vacuums

Belt repair how do i replace the belt on kenmore canister progressive

If im right on the top where you change the settings for your carpet there should be 2 screws take th e whole top cover off theres a plastic cover for the belt take that off and the rest should be self explanitory ... Kenmore 25812 / 25813 Progressive Bagged Canister Vacuum

This concerns Kenmore Progressive vacuum 21637115700 part 23 2CKG352000, the belt driven brush bar. I had to take it out for some serious cleaning and it expanded in length about a quarter inch as it is supossed to, I guess. How do I collapse it back so I can re-attach the belt and brush? Thank you

Hello. i can assist you. the bar will collapse back in one of two ways either direct pressure exerted on the ends or by a twisting motion applied to one end and or the other. use a pair of pliers or a wrench to get a grip on it if you need to. re ... Kenmore Vacuums

Change the belt in my kenmore power-mate 120 amps...how to open it to get to where the belt is???

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3468 seconds