Having problems with your Vacuums ?

I have a InStyler (the rotating iron) by Tre Milano. This device is for styling hair. This is not a flat iron, but a cylinder that warms up and rotate's against a brush. It has 3 heat settings which works fine. Problem is cylinder has stopped rotating. My husband disassembled and believes the motor for the rotation has worn out? This is the question he had and mine is can it be replaced ? I have model number. . IS-1001 120v 60hz 135w. Conforms to UL STD. 89 0927-037875. Also stamped on the small


Answers :

I'm repairing an Instyler right now.
\012Troubleshooting, I connected a multimeter and measure the voltage where the motor is connected. When I push the button that makes spin it, I measure 12Vdc which is a correct value for that motor. Then I connected the motor and it did not spin. Therefore I need to buy one motor here:
\012http://www.makepolo.com/products/Linear-Motor-with-4.5-to-24V-p39074920.html
\012
\012Same motor... yes you can repair it by installing a new motor.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a InStyler (the rotating iron) by Tre Milano. This device is for styling hair. This is not a flat iron, but a cylinder that warms up and rotate's against a brush. It has 3 heat settings which works fine. Problem is cylinder has stopped rotating. My husband disassembled and believes the motor for the rotation has worn out? This is the question he had and mine is can it be replaced ? I have model number. . IS-1001 120v 60hz 135w. Conforms to UL STD. 89 0927-037875. Also stamped on the small


I'm repairing an Instyler right now. \012Troubleshooting, I connected a multimeter and measure the voltage where the motor is connected. When I push the button that makes spin it, I measure 12Vdc which is a correct value for that motor. Then I co ... Vacuums

I havea Bissell ProHeat Model 7901. My problem is that the brush doesn't rotate. I have removed the access cover and both belts and found that the central cylinder for both belts is frozen and will not turn easily. Both belts are fine, except they are now burnt from this cylinder not being able to rotate. What I need is how do I remove the top cover to get at this cylinder to remove it and free it up?


... Bissell 8910 ProHeat Clear View Upright Vacuum

Conair does not sell the springs for their curling iron. Mine keep breaking and I do not want to keep buying a whole new curling iron just because the wire spring has broken. Instant Heat curling iron, model number CD8sWCS. Do you know where I can buy these springs or how I can improvise with something that will work almost as well?


Hi,\015\012\015\012The best thing I know of is to take a wire bread bag tie....take the paper off of it so that you just have the wire part... twist this around the two ends of the wires where it broke...this will contect the two wires an ... Conair Vacuums

I am a Philips pensioner and purchased a "AZUR EXCEL PLUS 555" steam iron from them many years ago.There is now a fraying of the cable as it leaves the iron with resulting in arcing. There is a detachable backplate on this model which allows corded or cordless use but which cannot be accessed to allow for cable repair by the user. My qustion is can this be repaired or if not can I still purchase a replacement backplate complete with new cable as I this is a great iron and a credit to philips


... Vacuums

Hello. I have an electrolux glider upright bagless vacuum cleaner (UK model) who's brushes do not rotate any more. I'm guessing that I need to replace the drive belt but I have no idea where to start. I would appreciate any tips. thanks


Hello! There are two solutions to this as the Glider model you speak of could be the more old fashioned type where screws on the bottom foot plate (ie where the spinning brush sits) have to be undone in order to get to the drive belt.\015\012 ... Electrolux Vacuums

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating


... Vacuums

Dyson18 bar will not rotate - Dyson Dc-18 "slim" Upright Model Replacement Motor Filter Part


... Dyson Dc-18 "slim" Upright Model Replacement Motor Filter Part

I HAVE MODEL FC8269-FC8250. I NEED REPLACE CYLINDER FILTER FC8028 AND MICRO FILTER 4322 000 38900. WHERE IN MAR DEL PLATA,ARGENTINA I CAN BUY THESE ITEMS?


... Philips Vacuums

We replace missing belt for roller brush on our bissell carpet cleaner, its loose and still doesn't rotate. Model # 8910 Looking for manual to fix this problem


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

Steam iron model 4488 schematic how to remove the thermostat button and replace it.


... Vacuums

Brush will not rotate. Have replaced both belts. Self propeled windtunnel model


You might need a new agitator (brush). if you caught something on it like : shoe laces, socks or anything that stops the brush. you should see on the brush were the v-belt goes burn marks or even gashes. this is a indication that you need a new brush ... Vacuums

Trying to replace cord on shark steam iron model gi500


I  don't konw but pandora charms ... Vacuums

I cannot find anywhere to buy replacement anti scale cartridges for my steam generator iron model DSG00001. Can you help?


If you can't find it ever, you can use bottled drinking water. Don't use purified water it is so pure that it can be a little aggressive on some metals. Just use RO or drinking water from your local store. ... Domotec Vacuums

Where can I get a replacement glass lid for Rival crock pot model #3100/2? The one listed below is out of stock, but, even if it were, it will not fit my model. Any suggestions? "Buy-it-now-store.com" lists: CURRENTLY OUT OF STOCK, NO ETA. # Rival Crock Pot Lid Replacement Glass for 3.5 Quart Rival Slow Cookers - $5.99 Rival Crock Pot Slow Cooker Replacement Round Glass Lid Cover # Works with Rival Crock Pot Models: 3100, 3101, 3102, 3103, 3130, 3133, 3120, 3250 # Approximate total


... Vacuums

My iron is dripping water my model number is dz6080 focus do i need a new one? It is coming out of the bottom when it is sitting upright. my ironing board is all stained and actually my floor is rusted from when I fold up my board and put it away it drips from the ironing board. I paid alot for this model.


... Rowenta Vacuums

I need to replace the plug in cord on my rowenta iron. I would replace but I paid $130 for iron and my cats have chewed on the cord so I thought it "might" be a simple replacement.


This is the second cat-chewed-a-wire question tonight.\015\012\015\012The only thing to do is to replace the entire cord. You could cut out the chewed section and splice it with **** connectors and electrical tape, but you have a nice iro ... Vacuums

Hello, I have a Hoover quadraflex Powermatic central vacuum system Model # s8099-031 that requires a new replacement 35 ft hose...I have contacted Hoover and they do not know where to buy a replacement hose for this model. I live in Canada. Any idea where I can get a replacement hose for this system? Thanks kindly, Tammy


Tammy, no info re your location, so I''l try this.Your Hoover hose is shot because it was made of rubber.There are new swivel handled, tangle proof lighter hoses made of vinyl which will last much longer and can be adapted to the old Hoover hea ... Vacuums

I have a Euro Pro Compact Performer model # EP 171 which I love. It is the best iron I have found for my quilting class. When I went to use it, I found my cats had chewed the cord to the point that it is unsafe. I took it to a repair shop to have a new cord put on it and they told me it had to go back to the factory. I do not want to purchase another iron because it is my understanding this model is no longer made and because I love it. May I send this iron back to the factory to have a new


Hi, you may already have found a solution, but I recently saw this same model iron on ebay! ... Euro-Pro Vacuums

Have eureka 9734 replaced belt, put back together,brush rotates well but vacuum is not picking up anything, no suction.


It sounds like the machine is clogged. Check the port behind the belt and any and all hoses for obstructions and remove. ... Vacuums

Hoover Elite II Model # u4689-910 Impeller replacement


I have had to use a dremmel tool to cut the plastic around the shaft, you can also something sharp and a hammer to break away the remainer of the fan. There are no threads on the fan so to keep truning it may or may not get it off. Just have to wat ... Vacuums

Question mark light has come on my vacuum and it wont run. I replaced the bag, but it wont start. I don't have a new filter is that the problem?


... Electrolux Vacuums

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

We are unable to find a replacement part that the filter attaches to in the dirt cup on our Eureka Boss Pro Model 411. This part seals the top of the dirt cup and holds the filter in place. What is the part name or model number for the replacement?


I just called Eureka (1-800-282-2886) and asked for the dust cover lid. It was part number 61538-1. They said they could ship it to me or I could call one of the authorized service centers nearby to see if they had one. I wasn't in a hurry and the ... Eureka 411A Upright Vacuum

I Have two questions concerning my AIRVAC AV2500 Red Series Vacuum System. How do you replace the light in the floor power head sweeper and can you replace the permanent fabric filter? We had the system installed in 2004 and the light in the sweeper head just went out and can not find any manual on line on how to replace it. The filter if not torn but avter 6 years it probably needs some kine of cleaning or replaced even though it says permanent. Any help would be appreciated. Jim McCluskey


... Vacuums

I need to purchase new blades for our 52" Jericho IV ceiling fan, Model 166315. I went to home depot in Harrisville, UT and they said that we would have to contact you and they didn't have ANY replacement fan blades in stock. HOW COULD THAT BE WHEN THEY HAVE HAMPTON BAY FANS ALL OVER THEIR LIGHTING SECTION? What kind of a business are you running when one can't get replacement parts? Our fan is making noise and I want to replace the blades. How hard can that be? By-the- way; I hope you no


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1027 seconds