Having problems with your Vacuums ?

Need a handle for a craftsman 16 gal wet/dry shop vac Model 758 17860 (circa 1978)


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need a handle for a craftsman 16 gal wet/dry shop vac Model 758 17860 (circa 1978)


... Vacuums

I cleaned my 2 gal Craftsman shop vac and replaced the filter with a new one. When I use it now it vacuums fine but blows dust out the exhaust. I never had this problem before. What could it be? How can I fix it. Should I return It?


... Shop Vac 584-06-00 Canister Wet/Dry Vacuum

Where to order replacement parts 6'x 2 1/2" hose, crevice tools 1 1/4" also 2 1/2" and 2 1/2" to 1 1/4" conversion unit.I own a 16 gal 10 gal and 5 gal shop-vak I live in wisconsin.


Go to Lowes or other such stores and they have a section with all of that stuff. ... Shop Vac Vacuums

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

Model 52726-82 Gal Craftsman's Wet/Dry vac smells


... Craftsman 17026 Wet/Dry Vacuum

Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.


Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem. ... Vacuums

I own a hoover steam vac model f5915-900 and i currently have two problems. 1. the brushes are spinning at a much slower speed. 2. the steam vac is not picking up the water it leaves on the carpet. Please help Josie


The reason the brushes are not spinning is because the belt is slipping, the belt is the bad that connects to the brush to a shaft that makes it spin. Next problam is it is probobly clogged. so water is not going through all the way ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My Oregon Scientific BAR888 has 5 windows, 1. temperature, 2. humidity, 3. mb/hPa or inHg (switch at the back), 4. bars showing pressure changes over 24 hours, and 5. time/date. Window 3 gives an option to set something between 0 and 2500. Oregon say they only have one set of instructions for the BAR888 but they do not match my instrument as there is nothing included for my window 3. Trouble is I don't know what the 0 to 2500 relates to and therefore don't know what to set it at.(My model does n


... Vacuums

I have a craftsman wet/dry vac - 16 gal 5.0 hp peak motor. Serial 98065V 8058, model113. 177790. When I try to use the vacuum function, the blower works too. Debris is blowing out of the shop vac instead of staying in.


... Vacuums

Electrolux Genesis 1572F: 1) One of the two spring/clips/whatever that hold the upright upright for storage has busted. What is the part called? Where might I find a spare? Or should I go to a machine shop? 2) The power cord retainer thingy on the back of the handle grip has broken; any idea about part#, name of part, where to look? (I can't find a manual or whatever, exploded parts diagram, etc., online. I guess this is the planned obsolescence thing--after all, the machine is hardly even 2


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Eureka Model C2094-Type GW Vacuum 1 Bags-Belt- Beater Roller or bristles that go on roller-light bulb Vacuum 2 Bags-Belt-Beater Roller-Bulb-Plastic frame the motor bolts on-Metal holder the handle go in that lets the handle move up and down


... Eureka Vacuums

Craftsman 16 gal wet dry vac model 113 178081 manual


... Vacuums

I have a Craftsman brand shop vac [model # 113.77420]. It is still picking items when I sweep with it, but it has developed a very high pitched squealing sound whenever I turn it on. The sound makes it almost impossible to use. Any thoughts? Thanks, Bruce


I have the same problem with a CTC Shop Vac. It's he bearings ... they're worn out and dry ... no lubrication. I've trid taking the motor apart and lubricating the bearings, then it runs super for a few uses but then the squealing starts again. Oi ... Shop Vac 925-09-62 QSP Plus Wet/Dry Vacuum

Hi there ive just purchased a bissell 1623e but cant get the 1 of the 2 screws to line up and tighten in handle any tips? ive tried holding it at all angles pushing down pulling up still it wont tighten should i take it back to shop? as faulty?


Take it back as faulty no question about it should line up easy and screw in stright away ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

When trying to use my Hayden Model 3600 central vac when trying to turn on the unit runs for 1 or 2 seconds and shuts off and continues to do so while switched on. I have thoroughly cleaned the filter and dirk canister but the intermittent running still occurs. Any suggestions?


... Hayden Industries SuperVac 3600 Central System Vacuum

Need filter for craftsman6hp. 16 gal shop vac model 113.177060


They're availabe at Sears and Kmart. Lowes and Home Depot also have filters that will work. ... Craftsman 17765 Canister Wet/Dry Vacuum

I have a Kenmore central vacuum cleaner model number c107 34601. We have emptied the bucket and shaken the filter out to clean it. There is a filter that is filthy so we shook it out into a bag but the cleaner still seems to not have great suction. I notice there is a similar cap to the outlets I plug the central vac hose into on the unit itself that doesn't power the nozzle when used. 1 - what is this for? 2 - Should I somehow remove the entire filter and if so - can you tell me step by step ho


... Electrolux Vacuums

I have a Shop Vac Model#92P550A - Ultra Pro 14 Gal. 5.5 H.P. My employee tells me it would go on and off while being used and now it does not turn on at all. I am suspecting the switch could be bad but honestly have no idea whether it is the switch or the motor. Cord and plug are fine.


... Shop Vac (464-38-10) Canister Wet/Dry Vacuum

How to install dry filter to model 5275 10 gal shop vac


... Shop Vac 925-09-62 QSP Plus Wet/Dry Vacuum

Need a manual for the shop vac model # 2E200 - Shop Vac Shop-Vac& Mini Hang Up Wet/Dry Vac Vacuum


... Shop Vac Shop-Vac& Mini Hang Up Wet/Dry Vac Vacuum

Geni 2 speed 25 Gallon wet/dry shop vac.


... Genie Company Vacuums

Craftsman shop vac no power when turn on


I just picked up a similar model someone was throwing away. turns out there is a thermal fuse inside the motor housing that blew. I just need to find the values of the fuse and repalce with appropriate size. motor runs when fuse is bypassed. ... Shop Vac 925-09-62 QSP Plus Wet/Dry Vacuum

Switch for Shop-Vac model QPL650 - Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum


... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu


This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

Shop vac model 3331.5 H owner manual - Shop Vac 333-32-08 Blower Vac Wet/Dry Vacuum


... Shop Vac 333-32-08 Blower Vac Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0699 seconds