Having problems with your Vacuums ?

Hoover nano rubber gasket

\015 Took apart hoover nano canister to clean. Can not put back gasket\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover nano rubber gasket


... Vacuums

Replace rubber gasket on Hoover Nano Cyclonic Compact Bagless Upright Vacuum


... Vacuums

I am trying to find out a part number for a rubber gasket that goes on the inside of a Hoover Windtunnel Cyclonic Platinum BAgless upright. It is a very thin, light-weight gasket made of rubber that helps seal the filtering tubes. If you know where I can find a parts break down, please advise,,, JON [email protected]


Hi There,\015\012\015\012I'm not sure exactly which part you are asking about, so I went ahead and uploaded the parts schematic of your vacuum cleaner, that will diagram all the parts, and part numbers.\015\012\015\012If you n ... Hoover UH70015 Bagless Upright Cyclonic Vacuum

Dust collects on outside of canister on Hoover twin chamber bagless cleaner . I have replaced the filter & rubber gasket at bottom of the canister ,checked for blockage.


... Hoover Vacuums

Mice seriously chewed/ate the rubber gasket on the lid. Is it possible to just replace the gasket, or do I need a whole new lid for this Hamilton Beach "stay or go slow cooker"? Can you give me a price on a replacement gasket or lid too please? Thank you.


Contact the manufacturer here\012\012http://www.hamiltonbeach.com/contact-us/contact-us.phpregardsI hope I have been of help but please do not hesitate to ask if you have any further questions. ... Vacuums

Hoover F6025900 Steam Vac Widepath LS, I own this steam vac and I found bits of rubber under the machine when I turned it on, smelled like burned rubber from a belt? Can you please tell me if there is a belt on this carpet cleaner and if so, how to access the belt? I have taken out some screws and still cant get to the belt? Thanks


Well there is no belt, and not sure what the rubber would be from, everything is plastic or metal. Unless it is really an electrical smell, which means the motor is going bad.\015\012\015\012 ... Hoover Vacuums

Hoover nano vacuum no suction - Hoover Vacuums


... Hoover Vacuums

Nano is no longer sucking up dirt... - Hoover Nano Cyclonic Compact Bagless Upright Vacuum, UH20020/W


... Hoover Nano Cyclonic Compact Bagless Upright Vacuum, UH20020/W

Rubber smell, Hoover


Its your belt burning up. You have to take the bottom of the unit off to check the belt to see if it was rubbing against something or if it is broken. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover nano smells like its burning


... Vacuums

Proper way to attach belt on a Hoover Nano Cyclonic


... Hoover Vacuums

How do I replace the belt on a Hoover Nano Vaccum?


... Hoover Vacuums

Hoover F5914900 recovery tank gasket


Go to this link for all your spare parts and diagram..http://www.ereplacementparts.com/hoover-f5914900-steamvac-wit ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover spinscrub 50 smells like rubber burning


... Hoover Vacuums

Hoover nano cyclonic will not pick up how do you unclog


... Vacuums

Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught  on the metal pole?


Check the Idler Pulley part Number 43241004 (Item 13 in the IPB)http://64.49.205.183/v/u6451900.pdf ... Vacuums

Vacuum smell I have a new bagless Hoover Empower Widepath. When I start to vacuum, after only about 2 minutes, it starts to smell really bad, like rubber I would say. Is it band slipping, and how do I check that out to make sure??


Your belt is slipping, it is probably stretched and slips trying to drive the brush roll. Take the bottom plate off, check the brush also, make sure the ends turn freely. The belt runs from the brush roll to the motor shaft. If you can't get to th ... Vacuums

Solution for "the unit is making smoke rubber belt smell how do i change the belt...hoover steam vac f7225-900


There is no belt on this model. From your description, it is definitely electrical, possibly the motor. I would have it looked at a repair shop. ... Hoover F7225-900 SteamVac V2 Upright Vacuum

HI, my motorized brush barely turns.It makes a hot rubber smell. I took apart and noticed the spindle the belt turns on discolored from heat. Cleaned it, but still no turning of the brush.The vac is a hoover wind tunnel. As it moved accidentally touched the belt/ spindle and burned my hand a little. Very hot in area. Bright spark from motor noted. Was careful not to touch that part!


That means that the belt is stretched and it is slipping on the motor shaft, that is why it is hot and smells like burning rubber. You need to replace the belt. Here is the correct belt you need: ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I need a cap with a rubber gasket for a scunci portable handheld steamer model SS-1000 - where can I find it?


... Scunci SS1000 Handheld Steam Cleaner

Model #DYB350, need to buy a few rubber gaskets.


Google make & model on internet, that should get you info, pete ... Vacuums

I have a very old Soundesign Ultrasonic Humidifier. Model 1866. I need a water tank cap. This cap has a plastic pin in the middle of it as well as a rubber gasket type thing, this helps control the flow of the water. Can anyone recommend a substitute? Thanks Abbey


Just realize its an old post. just throwing mine out i would have sent u the cap. mine stopped shooting mist out cap is good oh well. linda c ... Vacuums

Hoover Windtunnel smells like burnt rubber replaced belts brush doesn't spin when placed on carpet height adjustments won't move


Sounds like you have a bad brush roll(48414115), take it out and see the the ends turn freely or not, if not, then replace it. Also check the the slots that the brush roll sits in to make sure they haven't melted. I am assuming that the ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I have a DC14 Animal Dyson. The wand was sticking, so I figured out the rubber gasket had stretched out. When I trimmed that it worked a lot better, but now the wand is locking up again.


Hi there, its Darran at Dyson.It would be worth contact us so that we can discuss the options available to you. you may need an engineer to visit to replace part of your machine to resolve this, however it may be a part we can send in th ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My Hoover Whisper Cyclonic is collecting the dirt but not taking it into the cylinder. The brushes were at one point starting and stoping due to the belt periodically turning,now the brushes are turning and the dirt just collects and I'm starting to smell a an oder like rubber burning.I've taken it apart and tried to make sure the is no clog. The one hose that I can't check is in the back right base, above and left of the right back wheel.


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0545 seconds