Having problems with your Vacuums ?

How do I change roller brushes on vorwerk ET340 cleaner


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I change roller brushes on vorwerk ET340 cleaner


... Vacuums

I have a VAX V12 vacuum cleaner which suddenly stopped. The smell indicated Carbon Brush Problems. I contacted a service agent who told me that it was not possible to change the Carbon Brushes brushes on this model and they would need to change the Motor Unit.. To me this sounds very unlikely. Two questions please. Is it possible to change the Carbon Brushes and how do I get the cabinet apart which looks very difficult. I am well qualified electrically to do this job. Regards James Beech


... Vacuums

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems


Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

Hello can you help me please? I have a Kirby G4 vacuum cleaner, It did work ok until it started to give off burning smell and lots of sparks from the brushes. I have changed these brushes, the motor still rotates but it still gives off sparks and burning smell. Do i have to change the motor as well? Can you help please? Thankyou Martin


Some debris, even sand or dirt, probably got into the motor, causing damage to the armature. If this is the case, you will need to replace the motor. The burning smell from the motor is generally a sure sign of a bad motor. ... Kirby G4 Bagged Upright Vacuum

I have an Oreck XL Platnium. It smells like burning rubber and the brush roller binds and stops as you pull it back and forth, even on a hard floor. I have changed the belt 2 times. I have taken the brush roller out and checked it. It seems to be spinning freely. What could be wrong??


... Oreck XL Ultra Bagged Upright Vacuum

Non working roller brush on dyson dc25 vacuum cleaner


... Dyson DC25 All Floors Bagless Upright Vacuum

I have an eureka power plus vacuum floor cleaner and i have no way of opening the botton to the brush to change my belt for the brush since the brush will not turn.


Look for two screws at the edge of the brush housing. You may see these ones on top. They will be black and recessed ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I accidently ran over a sock while vacuuming underneath my bed and the belt broke (brush does not rotate now). I've always changed the belts in my vacuum cleaners, but the Healthy Home manual states that I need to bring it into a shop so that a professional repairman can change it. I find this ridiculous and now wish that I never bought it. How do I change the belt myself? PS I have already bought a replacement belt.


... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

I got a Dirt Devil Versatile 3 in 1 design hand vaccum for a birthday present This has a suction type of cleaning. I would like a hand held lightweight vaccum cleaner with a roller type brush and cervice tool. I would like to clean carpeted steps. I want to return the above cleaner and get a voucher for another cleaner.


... Dirt Devil Vacuums

How do you change the roller brush on Dyson DC 33


... Vacuums

Change the roller brush on Dyson DC33


Click this link below for the manual for instructionshttp://support.dyson.co.uk/medialibrary/Files/Dys ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I just purchased a Dirt Devil machine on Monday, I finally got it put together today and the brushes are not moving, dust is swirling around but no brush movement, I have changed all the nap settings, nothing, I am having company tomorrow and I threw my other vacuum cleaner away, HELP ME. Thank you.


Sounds like you may not have the belt attached or it is broke. ... Dirt Devil Vacuums

When we changed the belt the new belt broke right away and the brush roller wouldn't spin. My husband cleaned off the roller and got it moving slowly again, but when we went to re-attach everythin


The thing you call wheels are actually called roller bearings that fit at both ends of the brush-roll there probably seized up you can get a new brush-roll with bearings from the link below. ... Dirt Devil Breeze Bagged Upright

Dc25 dyson upright vaccum cleaner. Brush inoperative. have changed on-off switch and the reset switch. the belt is intact and iam left with possible bad brush rotator motor???


... Dyson DC25 Vacuum

How can I change the belt on the kirby vacuum shampooer brush roller. There is no way to snap the roller out and it seems that trying to unscrew the end isn't doing anything either.Model 5584 renovation group is what is written on the shampooer attachment. The kirby is a heritage model 2HD - purchased in the late 1980's.


... Kirby G6 Bagged Upright Vacuum

Changed the motor carbon brushes on my Beam central vacuum cleaner equiped with an IntelliWatch system. This system includes the Alutron DB100 module. This Alutron module needs to be reset so that the vacuum cleaner can operate properly. I believe that this module keeps log of running time and disables operation after a predetermined time. Can you help me with providing a reset procedure that will reset this module. Thanks


... Sunbeam Vacuums

We have the pet steam cleaner bissell 12 amp, we tried cleaning off the brush, because the cleaner wasnt sucking up the water sufficently. a screw came out along with the belt roller, and we have no idea how to put the screw or the belt back on.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Kenmore InteliClean 116.35923502 Two, I believe unrelated, problems. 1) The InteliClean sensor lights stay amber and red even when the machine is in the upright position and the suction line is disconnected from the cleaner head. 2) There is a lot of vibration and noise in the agitator roller housing. I picked a little hair out of the roller brushes but other than that they were clean. Thank you for any suggestion you might offer.


I had the same problem with the amber inteliclean light continually on. I found the problem to be in the plastic housing that connects the suction hose to the back of the upright section. You have to remove three screws and gently pull ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

How do I remove the roller from the hoover c1429 vacuum cleaner in order to change the belt. Thanks.


That is an elite style upright. You will need to remove the hood by releasing for tabs around the outside of the hood/base. The brush will simply lift up. You may need to pry on the base with a flat blade GENTLY to get tabs on the ends of the roller ... Hoover Vacuums

Vacuum cleaner (true hepa 360 progressive) brush roller stuck by wound cord


... Vacuums

Lg luv3008 vacuum cleaner when I move the machine, the brush roller does not rotate


... LG Vacuums

Can't get it from Roller Brush Off to Roller Brush On


On some model there is also a plastic tab to unlock the roller brush, check it out. You must also have the right tool installed. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How do i change carbon brushes on kirby legend 2 cleaner


... Kirby Vacuums

How do I change the Brush Belt? - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


It depends on the type of ProHeat cleaner you have. But you can go to www.bissell.com and download the manual for your model and you can get the belt you need at ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

How do you attach the belt for the roller-brush on a Kirby Generation 3, up-right vacuum-cleaner?


Greetings,\015\012\015\012Please see the attached video on how to replace the belt on a Kirby Generation Vacuum Cleaner. This is an easy to follow step by step direction on the proper way to replace the belt, as well as do basic mainten ... Kirby Generation 3 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0907 seconds