Having problems with your Vacuums ?

Shark navigator, roller brush turning but dirt not going to canister.

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Shark navigator, roller brush turning but dirt not going to canister.

... Vacuums

Brush roller won.t turn. It turns for a sec. then shuts off. I have cleaned all clogs. This is a shark navigator. Can I remove bottom of vac to access the roller? The manual doesn,t mention this as a solution.

... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won't turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can't get it to budge. This is exactly what is keep brush roller from turning.

Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

When I turn the carpet switch on for Shark Navigator, it will grab the carpet when I push forward, but will not when I pull back. Any ideas what the p? I cleaned the brush roller of all hair/fuzz and no change.

... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula

There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums

Shark navigator brush won't turn on - Shark Navigator Bagless Upright Vacuum

... Shark Navigator Bagless Upright Vacuum

My Dirt Devil Vibe bagless vacuum started giving off a burning smell. The brush roller was jammed with hair. I immediately shut it off and cut the hair out of the rollers with scissors until it turned freely. When I turned it back on, the smell was gone but there's no suction now. Did I ruin the belt or something else?

It's more likely there's a clog in the hose somewhere, possibly where it connects to the power nozzle. Detach hose and check the PN. \015\012If there's no clog in the PN, detach hose completely from machine and try to drop a marble or coin th ... Windsor SR12 Sensor Bagged Upright Vacuum

Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?

I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Shark navigator lift away brush not turning - Shark Professional Navigator Lift-Away Upright Vacuum

... Shark Professional Navigator Lift-Away Upright Vacuum

Hoover WindTunnel Canister: Roller brush motor not turning

These motors have a fuse incorporated in the field winding and it sounds like that blew. These motors sometimes overheat at the front bearing and the bearing will melt into the plastic housing. This will cause the fuse to blow. It sounds like that's ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Dirt Devil Breeze bagless vacuum roller brush won't turn

... Dirt Devil Breeze Bagless VacuumVacuum

Hoover upright bagless vacum.motor runs, brush turns, no suction through hole behind brush roller. however there is suction going out of dust cannister filter flap to motor. what could possible problems be?

Sorry to read about your problem, I hope this helps you out.you have a clog between the brush and bagI tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Runs but doesn't vacuum/****. Sidebrush works fine. Cleaned the roller brushes, and that seemed to confuse the robot and now it keeps going backward a few inches, turning, and then starts going backward again.

Sounds like a sensor problem. pull and clean the front black/white caster assembly and the revealed movement sensor and the 4 cliff sensors along the bottom of the front. Make sure the front caster wheel turns freely. You may have to remove the rolle ... iRobot Roomba 560 Robotic Vacuum

Shark navigator roller will not turn

... Euro-Pro EuroPro Shark Navigator Vacuum

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.

... Hoover Tempo Widepath Upright Vacuum - Blue

Shark Navigator The brush roll light is green but it isn't turning

... Shark Helmet NV22L Shark Navigator Upright Bagless Vacuum

Loud rotating carpet brush noise: Just got my new Shark Navigator, but it makes a really loud noise when I turn it in the position to clean carpets. Is this normal?

... Shark Navigator Bagless Upright Vacuum

Kenmore canister. Brush is turning but spitting all dirt under and out the back of the head. I guess the suction is very weak or non at all. What is reseting overload protector doesn't work. Haven't tried yet but just in case. THANKS!

I would look to see if there is a clog. that would be the only reason that the power head would be spitting dirt in back of the power head. check the hose. ... Kenmore Vacuums

The brushed roller on my Hoover Upright Canister has quit turning. Is this a broken belt? A friend recommended a "reset" button--is there such a thing?? Everything else works fine; power, suction, headlight. That belt just doesn't work anymore since we accidentally caugght the edge of a throw rug.

Belt. There is no reset on this model. ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

My brush isn't turning - Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

This link is the manual go to troublshooting pagehttp://www.totalvac.com/manuals/Shark_Navigator_Infinity_Owners_Guide.pdf ... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

My Shark Navigator. The brush roller run intermittently in the run position.

... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

Roller not Turning for shark navigator model uv30026

This link is the manualhttp://www.sharkclean.com/manual/UV300_26_IB_ENG_SPA_110831_5.pdf ... Euro-Pro Uv300 26 Shark Navigator Lightweight Pet Hair

The roller brush at the bottom of the vacuum is not spinning, hence it isn't picking up the dirt. I am unable to find a way to access it so that I can see what is stopping it from turning. Can you help me?

Hello. uUsually when the roller brush stops spinning the belt is broken. TIp the machine upside down and look for several screws which hold the bottom together. Mark the location of each screw when you remove it as different lengths are common and ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Vacuum brush roller wont turn - Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

You dont say if you checked if the belt is still whole so my guess is the belt broke(it could've fallen off and not be there at all but you definately need a belt) check that and let us know ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1222 seconds