Having problems with your Vacuums ?

C120 nilfisk wont give enough pressure cuts out

\015 Works OK untill I adjust nozzle for more pressure then cuts out\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

C120 nilfisk wont give enough pressure cuts out


... Vacuums

Nilfisk C120 6-6 PCAD X-Tra Big Accessory Pressure Washer manual


... Nilfisk Vacuums

Nilfisk 125.3 losing pressure


... Nilfisk Vacuums

Nilfisk compact c120 vacuum - no power


... Vacuums

Nilfisk c120 vacuum - no power


The fuse is part of the motor so is not something that can be changed. Make sure that there isn't a break in your power lead at the plug. ... Vacuums

Fault Nilfisk Alto pressure washer


See the diagram and repair swtich: ... Vacuums

I have a karcher 350 water blaster that has suddenly lost water pressure. the motor still works but no pressure. If i give it 10 or more seconds it builds up a bit of pressure but when i pull the trigger the high pressure only lasts for a 1/2 second blast then just normal tap pressure. Can anyone offer advice . thanks


... Vacuums

Clarke scrubbers helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? ther


... Clarke Vacuums

Clarke Instructions helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? t


... Vacuums

Simplicity vacuum My vacuum just cut off and now it wont start. I pressed there restart button but nothing happens I have 2 fairly old Industrial hitachi dry vacuum in my workshop both 110v and both wont start. Both i was told were manufactured in Italy and both have a manual and auto switch. It has a black top, takes an orange paper filter inside and its bin is dark blue. Sorry i've forgotton the model number. I've inspected the wiring but it's fine, could it be the motor and how do i gain acc


Just take it in to your vacuum store. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Alto force 5000 pressure washer Q:- The motor cuts out and will not start again, I try changing fuses etc. Eventually it starts again? but for a short while before it cuts out again.


... Alto Vacuums

Wont steam wont give off steam


Hi,Using bottled spring water may help...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

My new domestic Pentax cam 50 water pump is sometimes going to 0 bar and not cutting in I would like to adjust the lower pressure from 1.5 bar (22 psi) to 2 bar (30).I have a diaphram type pressure tank.


... Vacuums

Bought a shop vac about 3-4 mos ago and while i was using it, it cut off and wont cut back on. This is the second shop vac that done this and I took the first one back and got this one and it did the same thing. It is a 12 gal. 4.5 peak hp.


... Shop Vac 401-12-00 Wet/Dry Vacuum

I have purchased a bellini pressure cooker and the beeping wont stop and it wont start cooking


... Vacuums

My new domestic Pentax cam 50 water pump is sometimes going to 0 bar and not cutting in I would like to adjust the lower pressure from 1.5 bar (22 psi) to 2 bar (30).I have a diaphram type pressure tank.


... Vacuums

The hand-held wand wont slide back into the tube. It wont go down far enough to click in and become the handle again. It was working fine but all of the sudden won't fit back in.


Sounds like the tube has something inside of it that is obstructing the path. veriffy the the "female" end of the tube isnt obstructed, and also, make sure that nothing is bent ( which can happen easily). use a flashlight to shine down into the tubes ... Dyson Ball DC24 Bagless Upright Vacuum

Nilfisk C120 vacuum cleaner - Fuse?


... Vacuums

My carpet cleaner will not spray. Maybe a little thru the tool but not enough pressure to SPRAY


Thanks to many others who have posted on similar problems -- water\015\012and/or solution sprays through the handheld tools, but not through the\015\012main machine.As others have suggested, I removed the water\015\012reservoir, which exp ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Adapter for hoselock to nilfisk pressure washer


... Vacuums

Cuts on and of then wont come back on at all for a


I had to slightly widen power plugs on hose by inserting knife blade between their segments so that they make better contact. ... Vacuums

The lid on my sc-306 steam cleaner wont come off, is it pressurized


Press down and turn antyclockwise ... Vacuums

My dyson animal just cuts out mid vacuming ,the motor gets quiet hot ,and wont start again for an hour or so when i expect the motor cools down .all filters cleaned no blockages etc.. any suggestions?????


This is a feature so that the motor does not burn up check all tubes ... Vacuums

Lux legacy my vacuem wont run but 1second after i push the on switch. the full bag light comes on when it shuts off.i turn it on again and it runs for asecond and cuts off. it has abrand new bag in it.i tried adjusting the suction knob on top to no avail.


Actually the problem is inside of the canister itself. You need to change a part called the control valve. Occaisonally when fine particles get inside of the valve it damages the inside of the valve, sending a false reading to the main motor, causi ... Electrolux Lux 7000 Bagged Canister Vacuum

My honda gx390 pressure washer is not starting. It is backfireing through the carb. Will run if I pull enough sputters them might kick in and run then will die. I have cleaned the carb & float bowl and changed the oit so it is up to leavel and seem to have spark but could be better spark. It was running (allthough not well ran out of gas and then I filled it up and this is what I have. Thanks for any help.


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0381 seconds