Having problems with your Vacuums ?

Hoover uh70015 motor noise, how to put oil or lube the motor

\015 I have a Hoover Platinum upright bagless that I really love. Through all the cleaning of hoses, HEPA filters and such now there is a screatching awful sound coming from the motor. I can disassemble it, but where would I put lubrication for this motor?\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover uh70015 motor noise, how to put oil or lube the motor


... Vacuums

I have a new Hoover BH50015 hand vac. The noise is terrible. It sounds like the bearing are bad. When you take off the cup and the filter and listen to the motor as it slows down after turning it off it definitely sounds like bad motor bearings. Hoover tells me the loud noise is normal. Can you help?


Yes the bearing is full of dust and dirt\015\012unscrew the housing and clean the bearing area and shaft\015\012then add a dap of Vaseline to the shaft and reassemble\015\012The shaft rides on a nylon bushing which acts like a beari ... Hoover BH50015 Bagless Handheld Cyclonic Vacuum

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga


I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums

Hoover motor replace.Has hoover put a better more reliable motor into their model SH80015 built in vacumes that were sold in 2010 and had a very high failure rate


... Vacuums

I have a Model U57809RM Hoover Cyclonic which started making a very loud noise. Changed both belts on it but the noise persists. It seems to happen when I put the handle in the 'engage to vacuum' mode. The minute I start to lower it the noise begins. Help!


Hello,You could have a broken fan in the motor and need to replace the fan. If the noise is coming from the brush area of the vacuum, you probably have a broken bearing in your brush roller and would need to replace the brush itself. ... Hoover Vacuums

Was hoovering when my DC04 made a funny high pitched noise then a whirring noise, this was accompanied by a smell of burning and a puff of smoke! Almost sounds like it might be a clutch slipping, is this possible or is it more likely to be a motor burn out?


OK... the DC04 doesn't have a clutch. My best guess is that the belt that drives the brush roll has broken. The smell of burning and smoke puff were probably caused by the motor suddenly speeding up when freed of its burden of driving the brush roll. ... Vacuums

I have a Hoover model F5876-900 SteamVac Plus 1200. The motor is making loud noises and it seem to come from the bottom of the motor itself, what can I do to fix it myself.


... Vacuums

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?


As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Where would OIL come from by the right side back wheel?I have a hoover wind tunnle model # u6425-920. Does the drive moter have oil in it if so and it is leaking should we replace the motor?


The motor does not have oil in it. The onnly thing I can think of is that if soemone had tried to free up something by using a spray lubricant, and not it is running out. I've never seen this issue. You would have to let a repair shop look at it. ... Vacuums

No motor when switched on two red lights flash,cleaned hoover, put back together motor started,then cut out after a few seconds


I would double check your wiring, Make sure all wiring is tight. No cracks, no pinched wires. If needed, bypass the switch and see if it will stay running. If so, switch would be bad. If it's the same, then you have a wiring problem or a worn motor a ... Sebo Automatic X1 Bagged Upright Vacuum

Hi, I have a Dyson DC04, (silver/lime) making ear popping screams! Does not happen all the time, and more noticeable when it is pulled back.The suctions not a problem and no funny smells or strange noises from the motor. Ive taken the base plate off and the belt and brush bar seem fine, but when I turn the belt, it seems to be the motor spindle thats squeaking, almost as if it need oiling, any help please


... Vacuums

I removed the filter from the motor in the ball. After I cleaned it and let it dry, I put it back in. From then on, it makes a moaning noise when I turn it off after I vacuum. I followed directions to clean it and put it back (it's pretty straight forward and fool proof). I've since cleaned the filter a second time, doing the same steps and it seems to have made it worse.


... Dyson DC25 All Floors Bagless Upright Vacuum

I cleaned out my dyson ball as it smelt when i hoovered, cleaned filters, washed out canister and took the screws out of the front bar so i could clean near the brushes.. now its making a high pitched noise and when i switch it off it makes a noise like an engine shutting down! Have i disturbed the motor?


Hi its Darran at Dyson. The screws on the base of the cleaner head should not have to be removed to access the brush bar so it is possible that the brush bar has come out of alignment, hence the noise the machnie is making. Pl ... Dyson Ball DC24 Bagless Upright Vacuum

We have a hoover porta vac. that at first it would sometimes come on and sometimes not. It did completely stop coming on, so I have changed the switch and the cord but with no luck. Could you offer any suggestions or is this a motor situation. To my knowledge the motor was not making any noise. Your help would be greatly appreciated. Thank You, Molly Maid of NW Fla.


If this has had heavy use, the carbons in the motor may be worn. ... Hoover CH30000 Bagged Canister Vacuum

Loud noise coming from motor on hoover elite rewind vacuum


... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

Hoover linx motor makes a lot of noise when running


... Hoover Platinum LiNX Cordless Stick Vacuum

Hoover UH70210 Windtunnel PAWS motor high pitch noise


... Hoover UH70210 Bagless Upright Vacuum

Is the motor shaft that you put the belt on the dirt devil bagless upright that silver bar. My vacumm now makes a screaming noise and doesn't pick up. the directions are very poor


... Dirt Devil M086700 Vision Bagless Upright Vacuum

The Hoover Steamvac 1600 Delux. How do you access the motor. It is making a loud noise and I want to open it to check if there may be something stuck within.


... Hoover STEAMVAC VACUUM Vacuum

Hoover SteamVac Model F6056-900 SteamVac/SpinScrub. Indicator light and high pitch suction noise indicates that dirty water tank is full. However, water level indicator (yellow bobbing plastic thing) is at the bottom of the tank and there is no water in the tank. Have check all the hoses for clogs, none found. Checked water port from motor area to receptacle tank for clogs, none found. Fixed broken hose to upholstery wand with duck tape, (wire not broken, just cracked plastic hose). The onl


There are 2 filters, make sure they are clean, one is on the tank lid, the other is from the bottom, it is red, pull it out and clean it. If yours has a foam filter on the tank lid covering the yellow ball, make sure there is at least a 1/4 in. gap ... Hoover Vacuums

When my dyson dc14 hoover is on it has a strange burning smell, and a noise like air popping, there seems to be suction from beater and it spins. and definitley suction from extension. Filters are clear and no blockages. Is it the belt I don't think it is. or motor ? Grateful for any advice.


It could be the belt. However, the popping sound does have me puzzled. The popping could be coming from a partially broken belt slapping against plastic.Jim ... Vacuums

I have a 1937 Johnson 4.2 HP Outboard Motor LT-37 Serial # 273761. The engine is seized and I am looking for info on the best way to free it. I've started by putting marvel mystery oil down the spark plug cylinders. Any hints and help would be appreciated. Thank you. Ron massauto


Do you think it is the engine or the lower unit? If the engine has set up for a long time it may be the lower unit or the prop gearing. Pull the bottom loose at the flange be-careful of any parts you take off and try and turn the engine then. If it s ... Vacuums

Machine makes a motor noise, but brushes won't turn. Can't see a belt anywhere & can't open it up. Hoover SpinSteam Model #F7431-900


Hello,\015\012\015\012This unfortunately is a very notorious problem for the Hoover SteamVac's. I have written a pretty detailed step by step guide on how to diagnosis, and fix this problem though. \015\012\015\012Here's a ... Vacuums

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi


Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums

Hoover h3030 Brushes do not spin,I have put in a new brush motor drive.


In thi picture, did you replace #20? It is what drives the brushes.\015\012\015\012 ... Hoover H3030 FloorMate SpinScrub 500 Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0681 seconds