Having problems with your Vacuums ?

I cannot turn my Fuller Brush canister sweeper on.

\015 The canister has on on button and the extension has an on button. What is the way to turn it on?\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I cannot turn my Fuller Brush canister sweeper on.

... Vacuums

Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won't turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can't get it to budge. This is exactly what is keep brush roller from turning.

Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula

There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

Bought a new sweeper and brush ( beater bar ) does not turn. The large belt is fine and turns. The small thin belt is also fine but does not turn the brush. It is either the wrong belt or is there something that could be missing to put tension on it ?? Thank You [email protected]

Jim, To put tension on the brush, tilt machine forward when upright, move carpet selector knob to carpet. then turn vac on. Brush will only spin when vac is tilted back to operate. brush stops when upright and on to use hand tools so the er is no dan ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Fuller brush canister vac won't start

... Fuller Brush FBPTCAN Bagged Canister Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help

The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

We have a kenmore canister vacuum and it runs but when turn on the rug clener brush the brush will not run we then put on small brush head and that will work

If the power head motor runs, but the brush doesn't turn, then the belt is broken. Replace the belt and it should work. ... Kenmore Vacuums

Hoover WindTunnel Canister: Roller brush motor not turning

These motors have a fuse incorporated in the field winding and it sounds like that blew. These motors sometimes overheat at the front bearing and the bearing will melt into the plastic housing. This will cause the fuse to blow. It sounds like that's ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

3760-4 Eureka Sweeper where brush does not turn

The belt broke or came off ... Vacuums

Older electrolux canister brush will not turn used reset button

Change the belt ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Older electrolux canister brush will not turn used reset button

How to disasseble the electrolux canister \015\012This procedure works on almost all Electrolux plastic body canister vacuums. Caution: Always be sure that your machine is unplugged from the electrical outlet before servicing ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Sweeper Brush doesn't turn.

Could be that too much hair, string, or long fibers have been collecting around the roller. Remove it and clean it off. Also check the duct behind roller that goes up into the connection hose. Ther most likely is some sort of blockage. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My Kenmore canister model (116) 26212601 works in hard-surface mode (basic suction), but the brush won't spin for carpets, and when I try to turn it on, it makes a whiny sound and then turns off as it does when I need to press the overload button. I looked inside a bit, and the belt isn't broken--it seems fine. So not sure what the problem is. Thanks for any help.

... Kenmore 27815 Bagged Canister Vacuum

Hoover Model U6425-920, Series Q 12.0. runs 3-5 minutes, shuts down on thermal reset. motor shaft and brush both turn freely. cannot detect any roughniss at all in shaft turning.

... Hoover Vacuums

I have a Kenmore canister vacuum - model 25614506. Some time ago, I was not able to turn the vacuum off with the on/off switch, but could still use the vacuum. Turned if off/on by pulling the plug. The other day when I went to plug it in, I heard a pop. Now the sweeper runs but the vacuum cleaner does not **** - no air flow. What could be the problem. The cleaner is only 4 years old.

The motor has an inline fuse ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

I have a Kenmore canister model 116.25812 that makes a very loud beating noise when the powermate is turned on. I replaced the belt, but still has the sound. Also replaced the bag and both filters. Suction is great, but is very loud when the brushes turn.

... Vacuums

I had to empty the canister and when I put it back on and turned on the vacuum, the suction does not turn on. The brushes are rolling and the attachment suction works fine. Any suggestions?

... Eureka 431A Optima Bagless Upright Vacuum

I have a cannister vacume, Fuller Brush red model # FB-DCC when I turn it on it will shut itself off in about 30 seconds this will happen several times then it will not turn on. I do not have the owners manuel

First, the word is "VACUUM." Second, it's obvoius that your motor is overheating. When's the last time you CLEANED THE FILTERS, per the operating instructions? ... Fuller Brush Vacuums

I have a Electrolux , EL6988 Canister Vacum, howeveer the brushes and motor will not run when turned on. I have take the plates and cleaned around the brushes, but it will not come one. The vacum comes on but the motorized bushes do not activate. Thanks I have lost my owners manual, and have looked for the reset button and can't find or know where it is located. Any suggestions.

I need the molded wire harness inside the plastic wand ( one of the prongs is broke off) What is the part # or where can I buy it? Model EL6988 ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Brush will not turn around, it runs but not the second speed with the roller brush. i cannot figure out how to rmove bottom

Ya you need to replace the belt. You can get replacement belts here:Replacement Vacuum Belts ... Vacuums

When I turned on the sweeper it would not start. I put a different power cord on it and it worked fine. now it won't start but the light on the brush and the bag full will flash when i turn it on and off but it wont start. i have 2 of these doing the same thing. do you have any idea what could be wrong. I have checked for clogs but have found none. Bob

Its sounds to me like the computer board inside the machine has gone bad. Keep in mind that the filters in these machine do need to be replaced regularly to keep the vacuum working correctly. Any good vacuum shop should be able to fix your problem. R ... Windsor SR12 Sensor Bagged Upright Vacuum

I have an Ambassador canister model Electrolux. The powerhead shut off and the brush doesn't turn. There is nothing wrapped around the brush and the connection from the handle to the power head is fine. Any suggestions? Thanks AG

CHECK TUBE-SUMO ACTIVE ( PART NO: 1131402-02 ) CONNECTION AND NOZZLE-SUMO ACTIVE OR REPLACED (PART NO: 1131400-02) ... Electrolux Lux 7000 Bagged Canister Vacuum

How to Replace Rotor Brush for Fuller Brush Electrostatic Sweeper

... Fuller Brush Repl. Brush for Electrostatic Carpet Sweeper - -

I cannot get the brushes to turn, now here is a dumb question does it take a belt as I am not seeing one on the brushes

Yes it does take a belt. This belt needs to be replaced every 6 to 12 months. Here is the belt you need and a manual with instructions:Bissell P ... Bissell 6594 PowerForce Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0856 seconds