Having problems with your Vacuums ?
How to take off handle of oreck axis vacuum
\015 How to take off handle\015
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
How to take handle off of oreck axis vacuum
... Oreck Vacuums
How to take off handle of oreck axis vacuum
Sears 116.31913 Lower units, vacuum motor and agitator power head do not have power/115v to them and won't run. I'm trying to take the handle apart to access the on off switch. I've taken all observable screws out and cannot separate the handle and section immediatly below the handle to access the on/off switch, to trouble shoot. Any tips for separating the plactic pieces enclosing the on/off switch?
... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
I have just purchased two (2) Electrolux Nimble vacuum cleaners. Not one, but both, straight out of the box, the beater bars will not run. It turns on, select carpet, and lower the handle, the red light to check beater bar/or filter lights up. You can reset the light by unplugging the unit, then plugging it back in, but with same results. Now the kicker, if you take out the handle, select carpet, lower the body by the carry handle, it will run and operate correctly, however, as soon as you r
I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.
... Windsor VS14 Versamatic Bagged Upright Vacuum
Handle broke and had to call in the duct tape. hate to trash the vac just for this reason (although i'd take almost any excuse to buy an oreck). is there any way to get a new "ergonomic handle"??? thanks
This site will probably help you:http://www.fixya.com/websearch.aspx?cx=partner-pub-8183356113384228%3A3nccpq-il5y&ie=UTF-8&cof=FORID%3A11&q=ergonomic+vacuum+handle&sa=Search#1392Jim ... Euro-Pro NV31 Infinity Vacuum
I have a hoover windtunnel upright vacuum, It will not shut off and I have to unplug it to do so. If I take apart the upper handle and manually flip the internal switch it works just fine, only when using the external switch on the handle, wont shut off.
This is a common problem with this machine. The switch has too much resistance to be turned on and off with the switch button and rod. If you put in a new switch, ( # 28161075 ), your problem should be fixed. ... Vacuums
I have an Electrolux Renaissance Vacuum C104H. How do I get take the hose off of the handle to install a new hose but keep the handle I have?
Oreck xl21 loose handle - Oreck XL21 Bagged Upright Vacuum
... Oreck XL21 Bagged Upright Vacuum
Oreck XL My Oreck just turned off in the middle of vacuuming and I smelled a burning smell. I am thinking that if I can take it apart and remove whatever turned it off, it will run again.
Your roller brush is probably bound with hair and is not able to move ... Oreck XL2600 Vacuum
Hi, I vacuumed a small rubber bouncy ball up into the vacuum by mistake. The suction is not as strong now, and I'm not sure what to do. Where I can easily take the hose apart (eg. at the handle places) I cannot find the ball. What do you suggeest?
How do I take oreck apart? - Oreck XL Ultra Bagged Upright Vacuum
5 screws on bottom plate. Then couple to hold fan housing and motor. Not a bad job just takes a little juggling finesse. ... Oreck XL Ultra Bagged Upright Vacuum
Take fly wheel off of a oreck orbiter - Oreck Orbiter Floor Machines ORB-500, ORB-550, ORB-600 Vacuum
... Oreck Orbiter Floor Machines ORB-500, ORB-550, ORB-600 Vacuum
Take handle apart sebo vacuum - Sebo Automatic X1 Bagged Upright Vacuum
... Sebo Automatic X1 Bagged Upright Vacuum
My Kenmore progressive canistor vacuum has a loose electrical conection in the hose handle. How do you take the handle apart?
There are 3 visible screws there in the handle and one not so visible. start by removing the 3 visible screws.Take a flat screwdriver and pry off the colored portion of the handle that would contain the switch. There is one mo ... Kenmore 25512/ 25513 Progressive Canister Vacuum
Need to take off handle of vacuum
The bottom section is a pain, doesnt seem to wanna release even with the screww out. I work around it. ... Oreck Vacuums
My dyson slim vacuum doesn't switch from hose to floor mode. I thought the foot lever was broken. I realigned it but it doesn't switch now from floor mode to hose mode. I take out the hose and I can see the white part. I thought it should move as you go from upright to recline position of the handle.
The changeover valve is not activating - call the Dyson helpline - they'll set you up for a repair with a repair dealer in your area. ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow
Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it
The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum
The model is U5720950, there is no suction at all when I lower the handle to vacuum. But when I use the parts, they work properly. I cleared the roller and put everything back in place. Did I misplace something? Can I fix it myself without taking it to service?
... Hoover U5720-900 WindTunnel Upright Vacuum
My Oreck XL was working fine, then when I vacuumed a shag rug is started smoking and smelled like something is burning. (I changed the bag, checked for clogs--none found, and roller brush is turning. It has a metal handle.) Now I am afraid to use it.
Even though the brush is spinning, the belt is probably worn out and stretched. when you vacuum the shag carpet, it puts more drag on the brush. try running it on a shorter carpet or hard floor for a few minutes. if it doesn't smoke, then you know i ... Oreck XL2000 Bagged Upright Vacuum
How do i take apart an Oreck srteram iron - Vacuums
Mount it in the cord base and move the switch to the "wireless" setting to remove the cord assembly from the iron.- There are 2 small while nubs on the bottom of the blue plate in back. These are plugs. Pull them out to expose 2 screws.- ... Vacuums
Cannister model#11627915701. connector terminals in extensionwand ,and wlre harness in hose handle get hot,,,look a bit singed.. can order and do ourselves. but would like a "tune up " ,cleaning of vacuum as well. purchased in 2008. have long haired dog,,,can't afford to be without it for very long. have sears store in clay ,ny. lady I spoke w/ says it would get sent out and take at least 2 weeks.!
... Kenmore Vacuums
Orek website diagram for wiring orek handle - Oreck XL Ultra Bagged Upright Vacuum
... Oreck XL Ultra Bagged Upright Vacuum
Oreck XL21 just will not work at all any more. Beater is clean - belt is fine. Fresh bag - inflates. Took the thing apart - checked for blockages at intake, bag entry, and the tube. It just doesn't vacuum anything. No suction at all for anything stronger than air. I'd say it doesn't ****, but that would be ironic. Are these known for just "quitting" after a while? We take it in for maintenance as recommended to replace filters, etc. Is there some miracle trick to make it work or sho
Did you make sure the brush turns freely? Even though it is clean, if it does not turn freely with the belt, it will not beat the carpet and pull debris up into the unit.\015\012\015\012Another (drastic?) thing to try would be to take the unit ... Vacuums
Wire is loose in the handle of my oreck xl clasic i have to hold it to make the vacuum work what can i do
... Oreck XL2000 Bagged Upright Vacuum