Having problems with your Vacuums ?

Vax mach 5 assembly

\015 I can not see how to refit the rubber seal to the plastic tube.\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Vax mach 5 assembly


... Vacuums

Rotating brush will not turn om Vax Mach Air - VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Vax mach 3 allergy new belt how to fit - VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Hissing noise on my Vax mach air - VAX Appliances Vacuums


... VAX Appliances Vacuums

Vax mach air reach vacuum cleaner user manual


... Vacuums

How to replace belt on vax mach air


... Vacuums

Vax mach 7 upright overheating and no suction


... Vacuums

Vax mach 5 burning smell and revving loud


My mach 5 has lost suction and the brushed are spinning ... Vacuums

I have a vax mach air u91-ma-b where's the drive


Click on the link below and you can dowload the manual witch will give you instructions how to change the belthttp://support.vax.co.uk/power-2-upright ... Vacuums

Need to down load instruction manual for Vax U89-MA-PF mach air bagless upright cleaner


... VAX Appliances Vacuums

Vax Mach 7 - the brush bar won't rotate but the belts are fine


... Vacuums

Vax 121 assembly diagram


... Vacuums

Vax c91 m3-g-a mach 3 complete allergy - Vacuums


... Vacuums

Vax mach 7 brushbar


It is either the brush that is worn where the belt fits or it is the drive pulley (the other end of the belt). Check both closely for signs of wear but probably a worn drive pulley is favorite. They cost about 12 quid and are held on with four scre ... VAX Appliances VZL-6017 Bagless Upright Vacuum

Vax mach xp reach seems clogged and light is on


Clean the filters as per the user guide AND remove the silver, where the clear plastic handle is. On te back by the purple catch to release the dirt container is a screw - remove that and then remove the 3 screws on the purple lid with holes in it, r ... Vacuums

How to fix vax mach zen


... Vacuums

Roller brush not working on vax air mach 6


Hi I have a vax mach air light.the brushes wont turn but the green light is on. I have checked eveything .The little button on side tube no blocks .Checked all filters. ... VAX Appliances Vax X3 Bagless Upright Vacuum

Vax mach 7 cuts out then restarts after a few minutes


... VAX Appliances Vacuums

Vax mach 6 brush bar does not spin properly. does not spin at all on lower carpet settings and also when it is being pushed forward


... Vacuums

Vax mach 7 cable rewind spring has detached - Vacuums


... Vacuums

Instruction manual for a vax v11 vacuum cleaner [ use & assembly ]


There is no specific manual available for this model, but you can get the Vax V series manual and technical reference guide.\015\012\015\012\015\012 ... Vacuums

Brushes not working on vax mach air


... VAX Appliances Vacuums

Red light on vax mach air - Vacuums


... Vacuums

I have a vax mach 6. There is very little suction when using the tools and it will switch itself after a few minutes. I have had it to bits and cleaned it. I can not find any blockages. The belts also seem fine.


Http://www.vax.co.uk/downloads/pdf/u90-m5_u90-m6_series_user_guide.pdf ... VAX Appliances Vacuums

I need to change the motor in a vax 6131 but i don't know how to get into it to get the change it? I also need to get into the motor assembly housing to change a part but can't see how it comes apart!!


On the handle there is one small pozidrive screw, remove and orange panel comes away revealing powercable securing bar. Remove 2 screws and this reveals a 10mm headed bolt. Under label on top of handle there is another small pozzi screw, undo t ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0303 seconds