Having problems with your Vacuums ?
Kenmore cannister vaccuum Model #116.34924401 roller broke
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Kenmore cannister vaccuum Model #116.34924401 roller broke
I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?
First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums
Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.
Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? Thanks
Hi\015\012\015\012To remove the broken part from the latch use a small screwdriver to release the tabs on the latch on the connector. When latches are released the latch assembly and the plate will slide out of the connector. When the pla ... Kenmore Vacuums
Roller brush on Kenmore model: 116.31199100 won't turn
Refer to Larryclare1's solution at http://www.fixya.com/support/t1095798-kenmore_model_116_powermate_jr_stopped It worked great for me. Replace the belt, which you can get at Sears Parts store/online and clean out the hair as per Larryclare's in ... Kenmore Vacuums
Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won't turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can't get it to budge. This is exactly what is keep brush roller from turning.
Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn. ... Kenmore 25512/ 25513 Progressive Canister Vacuum
I need a new roller brush for Kenmore model 31075 vacuum. Is it interchangable with other models
No is NOT interchangable, you must buy from Kenmore.God bless you ... Vacuums
I have a 31200 model kenmore intuition vacuum cleaner the roller isn't turning
... Kenmore Vacuums
I need an owners manual for the Kenmore Evo Vaccuum. The model number is 114.85925500. Thanks
Http://www.managemylife.com/mmh/owner_manuals/20868/KENMORE-Power-Steamer-L0601245 ... Kenmore EVO All Surface Floor Cleaner Vacuum
I have the Kenmore Model 116.36722600 Vacuum; while cleaning the carpets the vacuum all of the sudden stop working; I didn't smell anything burning; it was almost like someone unplugged it. I checked the rollers and I can move it forward and backwards with no problem. Do you think the motor just burned out? Does this vacuum have a fuse that I can reuse? I love this vacuum and would hate to toss it. thank you
Kenmore upright vacuum model 116 32612200 roller brush
I have a Kenmore canister vacuum model #11625614500. I can't find the brush roller part to order online anywhere. Do you know where I can get one?
... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum
Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.
Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums
I broke the part that vacuums the carpet on my Electrolux cannister model EL 7020. Can it be replaced?
Yes, you can fix you power nozzle. Just look at the parts diagram at the following link: http://evacuumstore.com/s-90-el7020a.aspx\015\012This should help ... Vacuums
Kenmore cannister vacume model # 26312690 how do i change the belt ???/
My kenmore cannister vac (model 116.27514) has a slight burning odor after operating for a few minutes. We have removed the hepa filter and it looks like there is a strip of foam curled up behind the hepa filter compartment. Could that be the problem? How do we access that area? Thank you.
... Kenmore 22822 Canister Vacuum
Sears progression kenmore canister va. Model 11623612300 on the wand, the plastic piece broke off, there is one long wand with two piece to it well the plastic piece, not on the bottom, where it hooks into the beater bar thing, but the other plastic in the middle. Can this be replaces?
Hi.The part is probably available as replacement.Please click here ... Kenmore Vacuums
Kenmore cannister vacuum model 116.2411290 has begun exhausting a 'burned' smell. Suspect bad blower bearing. How to access?(Can't find manual online.)
Hi,how are you so sure the problem is from the blower bearing and not the belt,well to know if the problem is from the blower bearing or the belt you have to know how to access your vacuum first,so from all angle you need the manual You can download ... Kenmore Vacuums
I have a kenmore cannister vac - model 27514. Do I have to use hepa bags in it, or can I substitute another type, and which would that be?
You know, any bag made for the unit should give similar results. You can buy a cheaper bag and that number is 50558. You can get them at your local vac shop or you can let me know, I will send you some. The price per 3 pack is only 4.95. The cani ... Vacuums
Kenmore Cannister Vacuum Model 26312
Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=109396&thid=552260\015\012Kenmore Canister Vacuum Model 26312\015\012Posted by Alecia Rojas on Apr 28, 2008 ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum
Kenmore evo cannister vacuum model 116. Problem: low suction. I dropped it. How do i open it to fix it.
My kenmore vacuum model 116.36933502. It has no suction. I have cleaned out every spot,taken off the back and still nothing. The motor runs but doesnt seem to be at full power. The agitator brush works. When it broke i seemed to smell something and since it has no belt. Does this possibly have to motors?
... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum
After replacing the flat bet and v belt on my Hoover model U6433-900; serial No. 12300043057, purchased June 23, 2004, the brush roller still does not turn when I release the foot lever to vaccuum.
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=725351\015\012Generic problem for all Vacuums\015\012After replacing the flat bet\015\012Posted by maha ... Vacuums
Hoover Vacuum My Hoover cannister model s3614 "runabout powermax" suddenly lost power to the agitator roller in the rug brush. Where the wire cord enters the power brush, the covering has rubbed off exposing the wires which are not bare but still have their own covering. For a while the power came and went as I manipulated the wires but finally died. Is this something I can fix myself or is it going to be an expensive professional repair? (Warrantee has elapsed.) Thanks.
Our Hoover upright vacuum cleaner makes a very loud noise when it is running. What causes this? ... Hoover S3614 Vacuum
Kenmore Model no.116.29319800 Cannister Vacuum Cleaner manual