Having problems with your Vacuums ?
Frontier bush hog
\015 Problem changing the belt\015
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Frontier bush hog
1957 Sunbeam Twin-Blade electric lawn mower shaft bushing
Mower Man,Have you fixed your problem yet? I recently acquired the twin blade/twin chute mower with the same problem. You have to tap the roll pin out with a hammer & punch. A bit of a problem since you have to remove the motor fir ... Vacuums
Need replacement bushing part number for Kenmore, or motor?
... Kenmore Vacuums
Bottom roller bush does not spin
Sounds as if the v-belt came off the idler arm or you broke the v-belt. Either way, take the 4 screws out of the plate around the roller brush and make certain the belt is there and that it sits on the idler wheel. If you remove the roller brush yo ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Need a bushing for motor shaft and new brush
... Bissell 2050 QuickSteamer Upright Vacuum
Bush hoover blockage
My hoover Model F5858-920 bushes stop turning how can i fix it?
1. Check to be sure recovery tank is on right. This is the problem 99% of the time the brushes use a turbine powered by the suction. 2. Check to be sure the brushes are set to "on" if it has that option. And that the screen filter on the front of ... Hoover Steam Vac Carpet Cleaner Spinscrub F59149RM
Bush sc155h manual lost
How do you chane the belt on a bush 1700w hepa filter hoover
Had to take my black and decker leaf hog apart and am not sure how it goes back together. Is there such a thing as a diagram of the inside layoutg?
... Euro-Pro PT205 Leaf Blower Powerful 12 AMP Leaf Blower, provides 205MPH air speed, Detachable Vaccum... Vacuum
Impeller installation i took the whole vacuum cleaner apart to replace the impeller . i did not take note of the way the bushings need to be put on the shaft . do you know of a diagram out there that shows how to do this.
Here is my online guide to changing the fan. Hope it helps...\015\012\015\012http://reviews.e ... Kirby G4 Bagged Upright Vacuum
Why does the bush not work I already checked the belt is not broken
DC07s have two belts - one connects the output of the motor to the clutch, the other connects the clutch to the brush bar.I suspect the belt you ar ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I bought a new Bush MP2200BUK 2GB MP3 Player today and havent a clue how to download music from my laptop to my mp3 player and donw know if i have installed it right nothing is happening and dont know if i can download music from my frostwire (music download)
Does anybody know where i can get a new front cover for my 8gb bush mp3 player ... Vacuums
Bush sewing machine manual I have misplaced my manual for this machine and need to download a copy of same. Can you please assist?
HOOVER STEAMVAC Model# F5842-9RM 120v 12 amp Carpet Cleanerworks well. Hooked up upholstrey attachment, used it. Reassembled to standard operation, the aggitator brushes do not work. I dis assembled brush insert verything good. ran cleaner and the square hole that the bushes insert into did not rotate with cleaner on. turned off lightly tried to turn mechinism in machine no luck. Reassembled aganin, reinserted cleaning tool, then disconnected it. agitator still doesn't work. toggled switch
... Hoover Vacuums
There is a shaft that comes out of the pump of my Bissell 1623-1 Power Steamer with gears on it. The belt to the brush attaches to it. When I went to change the belt, the belt was fine but the gear itself with the small shaft on it was no longer attached and just dropped out. It looks like there might have been a bushing there, but no more. Any ideas?
... Bissell Vacuums
I have a bush 1700w hepa filter vacuum and need to replace the belt but I don,t know how to get into it ?
... Windsor SR12 Sensor Bagged Upright Vacuum
Trying to find a manual to replace power bush belt
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
My steam scrubber is not sucking up the water from the carpet into the discard container, and bushes not spinning.
The 2 most common problem is that the round filter inside of the lid for the dirty water bucket is up too high. There needs to be a 1/4 inch gap or so. The other is that the lid is not locked on the the bucket. ... Hoover F5906-900 Upright Steam Vacuum
Bush vacuum cleaner model no HR878B
The spinner bush turns really slowly. It doesn't
U need to get a new belt. a local hardware store or walmart carries it. also u need to take the vacum apart further so u can clean out where the motor spins u will get much bettter results ... Eureka Vacuums
I have a Electrolux , EL6988 Canister Vacum, howeveer the brushes and motor will not run when turned on. I have take the plates and cleaned around the brushes, but it will not come one. The vacum comes on but the motorized bushes do not activate. Thanks I have lost my owners manual, and have looked for the reset button and can't find or know where it is located. Any suggestions.
I need the molded wire harness inside the plastic wand ( one of the prongs is broke off) What is the part # or where can I buy it? Model EL6988 ... Electrolux UltraLux 2000 Bagged Canister Vacuum
What is the size of the drive belt and where can I source one from for the Bush Cyclonic Hoover DD9504B? Thanks steve
Bissell Pro Heat 2x carpet cleaner water tank valve is messed up. All the parts are there, spring, metal ring, rubber bushing and pin. How are they supposed to go back together?
Here is a picture, maybe it will help, part #2036675, which is #7.\015\012\015\012 ... Vacuums
Bad beater bar end bushing for eureka 5860--part number??
... Eureka 5860A Bagless Upright Cyclonic Vacuum