Having problems with your Vacuums ?

Vax turbo tool not working

\015 My turbo brush tool Has stopped working. I have cleaned it and removed any hair and debris but it still won't spin.\015\012Please help.\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Vax turbo tool not working

... Vacuums

My vax turbo boost 1700 cuts out it is not the filter i think it is the cable because if you hold it in a certain position it will work as long as you dont move the wire what do you suggest

... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Fein Turbo II vacuum will not turn on. No power to power tool outlet for auto on and will not work with manual off/on. Is their internal fuse or reset ? If so how do I get to it.

Check that theres voltage getting through cable ... or just change it :) if ok check motor brushes . ... Fein 9-55-13 Turbo II Bagged Canister Vacuum

Hoover turbo cyclonic only 12 weeks old stopped working while cleaning. I was using the hand tool and after about 3 minutes it just stopped and will not turn back on.

Try changing the fuse in your plug ( uk ) if this fails to fix it , have it repaired under warranty \015\012 \015\012\015\012 \015\012 ... Vacuums

Tools don't work - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Hi Nick. Sorry to hear you're experiencing difficulty with the tools. I understand how frustrating this must be. Here's a quick link to the troubleshooting steps to assist you: ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a Bissell Proheat Turbo 2x model 9300. It has stopped spraying at the floor. The hand tools will work so I assume this means the problem is at the base somewhere. I cleaned the nozzles but don't know what to try next. It has always had a problem with dumping too much cleaning solution as well, don't know if this is a contributing factor

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Hoover Max Extract LS F6056900 Hand Tool not working / Cleaning Solution I need to know what I need to get in order to have the hand tool work on this model. Also, what cleaning solution is best for pet stains? Tried cleaning, pre-treating with Spot Shot and towel and/or scrub brush, then cleaning, still doesn't work. PLEASE HELP!!

... Vacuums

I have a Bissell 9500 proheat 2X cleanshot w/dry Aire it works great on cleaning carpets. When I try to use the tools it will spray but will not suction. How can I get the suction to work when using the tools?

Ensure the handle is in the upright position and the selector is on tools,Please take the time to give this solution a fix ya ratingclarkco ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have the Bissell Proheat (7901) It will pick up water and the hand tool works fine. I noticed that the red indicator stopped spinning. Then I noticed no water was coming out. If I put down water using the hand tool, the vacunme will pick it up. When I called Bissell they had me do something with the indicator. When it didn't work they said take it in for repair.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Can the belt be changed on a hoover mini turbo pet removal tool

... Vacuums

Water and cleaner not coming out, The machine is only 6m old and was working fine, I have cleaned every where I can to see if there was a blockage but nothing is working. The heater is working, there is a suction but the water and soap will not realease when triger is pulled. it will not work on on the tool spay.

Check the complede length of the hose. You may find a crimp in the most inconvenient place. You say you cleaned everything ... can you blow through the hose where the cleaner comes out? (don't drink anything!) ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The tool attachment for the hose on my Bissell ProHeat 2X CleanShot won't spray soap or water. The bristles on the tool rotate without a problem and the suction is working fine, it just won't spray water when I pull the little gray trigger on the tool.

Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Vacuum will not run on manual or tool setting, but if the tools plugged into the outlet on the vac the tool will work, but not the vac itself

... Festool CT22e Vacuum

Rug doctor hand tool will not spray ...but it will vaccum....what can I do to get the hand tool to spray again ....tried another hand tool and that didn't work either ....help

... Vacuums

Base suction and tool suction both have stopped working

On the top of the water reservoir (under the handle that you use to lift it off) is a large dial. The top says "hose" and the bottom says "floor". Turn it to where it says floor. If your brush is not working than you going to have to tak ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have the Hoover upright windtunnel and have used it only once. It worked wonderfully the first time but now only the hand tool has suction. I can't find the book that came with it though. How do I get the main vacuum to work?

Seems like you must have suction at th hose. The either a belt came off or it is plugged up at the dirt inlet by the brush roll. Some Hoovers have a spring loaded door that opens and closes depending on whether the handle is down or in its upright ... Hoover Vacuums

Numatic Henry Hound Turbo Head stopped working. Checked wires and contacts and cleaned. lOOKED AT THE MOTOR IN THE HEAD BUT DONT know how to check it is working

... Henry Numatic "" Canister Vacuum

Hi the turbo brush with my new hoover whirlwind has stopped working. the suction on the appliance is fine and there are no blockages. have tried cleaning the head but it is still not working. any ideas//

... Vacuums

The tool doesn't work. No sucking power. However the vacuum works.

Hi,\015\012Check the hose...they plug up and then everything stops...\015\012Here is a tip that I wrote after having the same issues with my Bissell... ... Vacuums

The motor on my carpet tool (beater brush) stopped running yesterday. The main vacuum still works, but the switch for the carpet tool just clicks and doesn't turn it on.

You have to take it apart. Unscrew screws on bottom, short screw is at the front. turn over with top up. take plastic covering off first, then turn over again. unscrew retaining screws which keep beater brush in. take out beater brush. get seam rippe ... Electrolux Vacuums

Hoover SteamVac Plus 1200 upright hot water extractor Water/carpet cleaner applying o.k. Suction on the "floor" does not work. Suction on the hand tool works somewhat, but water is not collecting in the bucket. There is suction coming from the floor but water is not going into the bucket. It does not appear to be clogged because I can feel with my hand that air is flowing from the floor. The water is not being sucked into the bucket.

... Hoover Vacuums

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.

Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

Loose wire ive got a loose wire inside my vax cyclonic 1700w and ive stripped it down but cant see anything and its still not working but it was working when i moved the wire from side to side. Please help

Sounds to me like you have a open wire. There is a break in the wire inside to the insulation and as you move it, it gains and loses connection. You can test it with a continuity tester as you move the wire or just replace it to see if that solves th ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My Bissell 9500's base suction stopped working, however the hand tool suction works.

I can tell you how, but I think if you look at this manual it will show you how to fix your problems...go here to download: http://www.bissell.com/images/UserGuides/9500_908.pdf ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

VAX vacuum stops working after about five minuits use then I have to wait an hour before it will work again

The symptoms you describe are those of a machine that is overheating. Almost certainly there is a blockage somewhere, or one or more filters are clogged, thus impairing air flow. Clear the blockage and the problem should be solved.\015\012If this doe ... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0657 seconds