Having problems with your Vacuums ?

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga


Answers :

I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its supposed to. it just clogs up the filter. I put sellotape to seal the lid and it works fine.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga


I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums

Simplicity vacuum My vacuum just cut off and now it wont start. I pressed there restart button but nothing happens I have 2 fairly old Industrial hitachi dry vacuum in my workshop both 110v and both wont start. Both i was told were manufactured in Italy and both have a manual and auto switch. It has a black top, takes an orange paper filter inside and its bin is dark blue. Sorry i've forgotton the model number. I've inspected the wiring but it's fine, could it be the motor and how do i gain acc


Just take it in to your vacuum store. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Mine does the same thing. There is no suction. I found that there is a door that opens when you tilt the handle in the down possition. I think there should be a spring in place so it can open. Until I find a replacement spring I have to open the door ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Either the hose has a clog, or the inlet down by the belt is clogged. Is there suction at the end of the hose, if not then it is clogged. If there is suction, then it has to be clogged down below by the brush roll, check that inlet. There also is ... Vacuums

Hi. DC14 not running. Repeated pressing of the switch occasionally produces a split second whirr from the motor. I had been picking up plaster dust for some time but stopping regularly to clear out filters and 'the little tubes.' The switch is fine. I cannot see how to get at the motor. Thanks , Chris


Hi again. I finally figured out access to the motor. One of the brushes was burnt and broken. I have ordered a replacement set and cleaned up the comutator ( spelling ?). Thanks, Chris ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a hoover windtunnel upright vacuum, It will not shut off and I have to unplug it to do so. If I take apart the upper handle and manually flip the internal switch it works just fine, only when using the external switch on the handle, wont shut off.


This is a common problem with this machine. The switch has too much resistance to be turned on and off with the switch button and rod. If you put in a new switch, ( # 28161075 ), your problem should be fixed. ... Vacuums

Removed and reinstalled motor on Eureka model 6426a. Now power switch position 1 is dead. Power Switch position 2 works fine,


... Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.


Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

Hoover F7431-900 my carpet shampooer/steam vac was working fine until the brushes at the bottom of it just miraculously stopped working. they wont spin at all. Is this a motor problem? perhaps a water flow problem? please write back if you can be of any help. thanks


If the screen is not dirty, and the flapper valve to the turbine inlet is open, then the problem is mostly a stuck turbine impeller. The turbine impeller on my F7431-900 has seized TWICE!! The shaft for the turbine is not made of stainless steel, t ... Hoover F7431-900 SteamVac Vacuum

I cleaned out my dyson ball as it smelt when i hoovered, cleaned filters, washed out canister and took the screws out of the front bar so i could clean near the brushes.. now its making a high pitched noise and when i switch it off it makes a noise like an engine shutting down! Have i disturbed the motor?


Hi its Darran at Dyson. The screws on the base of the cleaner head should not have to be removed to access the brush bar so it is possible that the brush bar has come out of alignment, hence the noise the machnie is making. Pl ... Dyson Ball DC24 Bagless Upright Vacuum

When i turn on my yellow Eureka upright everything works but when i flip the switch on the handal to do the carpet the brushed do not work. The belt looks fine. Is the motor dead?


The brush is worn out most likely ... Vacuums

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall


That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

I have a Z345 Electrolux cylinder vacuum cleaner, from the 1970s probably, but not used much. I have lost the guide. I forgot to change the bag before it was full. Smoke started to come out - smelling of burnt paper, not rubber. So switched off. It did not blow the fuse, and may be OK. I wish to inspect it. How do I open it up? Alos I have an air filter and a motor filter for it. I have often changed the air filter on the top. How do I get at the motor filter, if there is one? Than


Good day! OK you have to is replaced the bag and that's it.And don't forget to change the bag again to avoid that problem.Thank you ... Electrolux Guardian Bagged Canister Vacuum

When i switch my henry hoover on it works fine for exactly 50 seconds then switches of for approx same time then comes alive again for 50 secs and so on...driving me nuts.


... Vacuums

I have a new Hoover BH50015 hand vac. The noise is terrible. It sounds like the bearing are bad. When you take off the cup and the filter and listen to the motor as it slows down after turning it off it definitely sounds like bad motor bearings. Hoover tells me the loud noise is normal. Can you help?


Yes the bearing is full of dust and dirt\015\012unscrew the housing and clean the bearing area and shaft\015\012then add a dap of Vaseline to the shaft and reassemble\015\012The shaft rides on a nylon bushing which acts like a beari ... Hoover BH50015 Bagless Handheld Cyclonic Vacuum

Switch Problem The red switch to put on wont stay on the motor runs but as soon as you release your finger from it the motor cuts out. what do I need to do to make it work as it should?


It sound like the switch is loose if you are able take the handle apart and plug the leads back into the switch. be sure to unplugit ffirst ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC17 beater bar motor works intermittedly. I have to almost whack it on the floor to turn it on and then shuts off again. I have checked the belt and it is fine, also have checked for blockages. The switch to turn the beater bar on or off will not work when the beater bar motor is off. the suction is fine though.


Buy a Kenmore for less money ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa


... Electrolux Vacuums

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work


It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

I was just using my Bosch 1450W bagged vacuum and all of a sudden, the motor just shut down. No warning, no problems. The light still turns on, but the motor is unresponsive. There is a clean bag and filter, and nothing caught in the front roller. The motor sounded fine - no shaking, or weird frequency variations. There were no weird smells, just a little bit of heat, but nothing beyond normal. I've had this thing for several years, and never had a bit of trouble with it. Any suggestions


Many vacuums have internal thermal switches that need to cool to allow the vac to operate. After 30 minutes, check all 3 air filters and try again.\012Gary ... Bosch BSG71310UC Bagged Canister Vacuum

Dead motor? My 8 year old Miele S251i has worked fine, until I was recently vacuuming and moved the plug from one outlet to another. When I restarted the vacuum, it made rrrrr.....rrrrrr....rrrrr noises and smelled like something was burning. I turned it off, and it's shown no signs of life since. Sound like a motor problem? I've taken the cover off and looked at the cord and seen the motor, nothing looks obviously wrong, but I'm also not mechanical.


... Miele S251 Flamenco II Bagged Canister Vacuum

Does the hoover runabout u427-930 have a filter? I replaced the belt and next to the light bulb was a square gray mat that looked like a filter covering a screen full of holes that looked like the motor was behind. I think it was a mat of cat hair so I took it off and threw it away; I just want to make sure that it wasn't a filter that I need to replace.


From doing a search on the internet and hoovers website it looks as if this unit does not have a filter. Such as a hepa that needs to be replaced or that is washable. So i think you are safe and dont need to worry about it. ... Hoover Elite U5061-900 Bagged Upright Vacuum

My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t


... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1136 seconds