Having problems with your Vacuums ?

Dyson dc41 hard to push on floor even with brush bar off, ok on carpet


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson dc41 hard to push on floor even with brush bar off, ok on carpet


... Vacuums

I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?


Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My Dyson DC07 has recently been service and was making a clattering noise and very hard to push. We have taken it back and he has changed the clutch mechanism under the base which has solved the clattering, but it is still really hard to push because of the suction. It is even lifting the carpet in one room. Can you tell me what the possible reasons for this could be? One thought we had was that the little rubber wheels on the bottom cover could have worn so the hoover is closer to the floor


On the sole plate you should have 5 little wheels, these are prone to jamming after a while. You should make sure these are not jammed in anyway.\012\012You can release these with a screwdriver, but be careful not to prize too hard as you ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The suction is good, but it can't pick up most of the stuff on the floor. The hand held hose works very well, but it doesn't even pick up little fuzzies reliably when I push it along. And, the suction is too hard I think because it used to push easily and now I have to push really hard, even on flat carpet.


Check entire length of hose, including the piece in the power head, for clogs. Simply drop a marble in one end and allow it to roll out the other. If it doesn't, then the hose is clogged somewhere. ... Dyson DCO7 Animal Bagless Upright Cyclonic Vacuum

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.


... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

Dyson dc41 hard to push on hardware floor


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My dyson animal is hard to push on carpet - the beater bar is still operational. When I turn off the beater bar and run the vacuum on hardwood the beater bar stops moving, but it still ''rolls'' on the hardwood - it doesn't pull up like it used to. It also seems to not be picking up as well as it used to, although no blockages are present and the filter is clean.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The vacuum is very hard to push on carpeting even when on hard floor level.


... Hoover Tempo Widepath Upright Vacuum - Blue

I have a dyson dc14. the brush bar will not rotate when the vacuum is running. the belt is attached and it will rotate by hand. when you switch from bare floors to carpet-the bar will not kick in and rotate.


\015\012Hi,\015\012Check that when you pull back handle to vacuum the clutch control knob which is located front lower left side of machine moves to drive position & is not stuck in off or park po ... Dyson Vacuums

Brush won't engage on my hoover windtunnel vacuum. I see the problem is that the "carpet / hard floor" slide bar is broken / jammed. How do I access the slide bars from below to unjam them?


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My dyson dc17 is very hard to push on a hardwood or carpet floor. When I take the canister off and push it while on it works great, so I figure the canister is giving me the issue. What o I fix? Thanks


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a brand new DC 24 (orange ball) Dyson. The brush is not turning and it is extremely hard to push on carpet. Something must not be engaged. What should I do?


... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a fantom wildcat vacuum, and the filter is clean, and I see no other clogs. The vac sucks fine on hard floors, but the roller brush does not move. I can't even manually push it around. S


... Fantom Vacums Fantom Wildcat 2100 Upright Vacuum

Dyson suddenly hard to push on carpet


I know this sounds silly, but it works. Turn it over and wipe all the black residue off the bottom of it (off the plastic on the bottom that rubs on the carpet as you push and pull it). I thought my husband was out of his mind when he told me that ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson DC18 brush beater bar intermittent failure problem.


Take it in to be serviced. It could be a dead motor to bad connection. 5yr warranty will leave you paying nothing. Best Buy or local authorized service center can do it. ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.


The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Just got my dc33... one issue... the dial switch to control btn bare floor / carpet mode doesn't seem holding in it's position when I set to the bare floor mode... it keeps coming back to carpet mode with brush-bar activated... the dial doesn't really click to the floor mode. Any advice on this?


Hi there,I'm sorry to hear you're having difficulties with your DC33. If you're concerned that the brush control doesn't seem to be staying in position, it's probably best if you get in touch with us directly. One of our experts will be h ... Dyson DC33 Bagged Upright Vacuum

When i set it on carpet instead of bare floor it is hard to push when i vacume (when i turn nob it only has two settings floor and carpet no high pile or low pile)


Hi there,Sorry to hear you're having difficulties using your DC14 on this particular carpet. You may want to contact your carpet manufacturer to check it's suitable for cleaning with a vacuum cleaner equipped with a revolving brush. Manuf ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?


Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums

My dyson C07 ANIMAL is making a loud clatter noise when I push the head down. I have removed the sole plate and the brush bar is cracked so I removed it, but I understand the clutch maybe a problem also from reading other people's comments..how can I tell if it's a clutch problem also? Or... could it be just the brush bar being cracked that's causing the loud noise?


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a


The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Older dyson dc 14 control knob for swithing from carpet to floor


Most likely you need to replace the clutch assembly. This video will show you how to replace it. \012\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Brush bar on Dyson DC19 doesn't work properly on carpet setting


... Vacuums

My dyson vacumn is hard to push on carpeting. How do i fix it?


This happens when the bristles in the brush roll get worn down too short. Put in a new brush roll and the machine will pull itself over the carpet, so you hardly have to push at all. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I just bought a Z1750 twin tech vacuum. I am wondering if I can buy a power brush attachment for this. It only comes with the floor and "carpet" brush but does not have the beater bar (power brush).


... Electrolux Centralux Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1136 seconds