Having problems with your Vacuums ?
Vax 6131t Burning smell coming from Vax 6131t
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Vax 6131t Burning smell coming from Vax 6131t
I have a vax swift Hoover burning smell coming out of the bottom
Vax hoover bagless, there is a burning smell coming from it
Most common burning smell is the belt in the power nozzle. check & replace. ... Hoover S3639 WindTunnel Bagged Canister Vacuum
Burning smell There is a burning smell when I run my Kirby Ultimate G. The smell seems to be coming from the belt. I looked at the brushes and they are spinning so the belt is working. the Post on the vacuum is getting very hot not sure if that is normal. What is causing this?
Unlock the sweeper brushes and take them out. on each end is a cup bearing and should be free of debris.then check around and under the belt and likely there is debris wrapped around it.the post is getting hot as your pulling too much of ... Kirby Ultimate G Bagged Upright Vacuum
Burning Smell coming from the moter
This could be a motor problem. There is always a slight blue arcing that occurs when an electrical motor runs and can be visible through the exhaust vent, but any excessive arcing indicates a problem. If the carbon brushes are sticking, this will cau ... Hoover U5262-900 / U5260-900 / U5266-900 / U5268-900 EmPower Bagless Upright Vacuum
Sewing machine Guru needed ;) Elna Grasshopper (new to me) circa 1950 The light works, but there was no hummm when knee pedal engaged. I have the motor out, and it is very stiff to turn. I'm at a total loss when it comes to motors and electricity. It doesn't smell burned, doesn't smell at all beyond normal machine smells. (Yes, I made detailed notes and diagrams as I took said motor out!) One other note. The long thing which my husband said might be a capacitor -- it looks like
I just purchased a fairly tidy Elna 'Grasshopper' sewing machine (1951) with the same leaking capacitor problem. I carefully removed the capacitor for examination. It is actually three capacitors in one - no chance of a direct modern replacement, but ... Vacuums
I heard that a class action lawsuit against Oreck Vacuum is being started because of all the problems customers are having with their vacuums. Does anyone know about this? My Oreck is only a couple of years old and keeps burning up belts. I took it in after only one week of usage when I started to notice white smoke coming out of it and the smell of burning rubber. I feel like I got the old run-around, when the service tech told me he couldn't find anything wrong (but replaced the burned up belt
You are correct about the fact that legal action has been taken. Go to this link to read more\015\012\015\012 ... Oreck XL2200 Bagged Upright Vacuum
My hoover 2000w pets cyclonic stopped working, there is a burn smell coming out off it
... Hoover Vacuums
Dyson DC25 makes a squealing noise and there is a burning smell coming from it.
... Dyson DC25 All Floors Bagless Upright Vacuum
Vax 2300 vax v-2300 brush is not turning so changed belt snapped as soon as i put hoover on and getting burning smell put another belt on same again and brushes still not moving only 4 months old
If the roller brush cannot be rotated easily by hand, it is likely that debris is jammed inside the end caps.Make note of the direction arrows on the end caps as you remove the roller brush. You will need to know this for reinstallation. The end caps ... Vacuums
The belt burnt out and it seems as though the red arrown does not release the belt. Like it is backwards from the green arrow. It had a burning smell and the belt broke. Then the second belt started to burn out when the brush roller wasn't spinning. Not sure what might be wrong. Green light will not come on either.
It sounds as if there may be a piece of the broken belt in there. Look carefully with a flash light and remove any remnants you find, using a pair of pliers if you have to.\015\012\015\012Also, remove the entire brush roller assembly and ... Kirby Ultimate G Bagged Upright Vacuum
My vacuum smells like it is burning - VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum
... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum
I shut my vacume off to change its bag out. Now it won't come on. Oreck xl2. There were no noises before turning it off or any smells of rubber burning. Just won't come back on. Is there a reset button. What can I do?
An access panel mounted atop a vacuum nozzle base via finger operated latches. When the latches are undone the access panel is removed from the top surface of the nozzle base allowing access to the parts of the brush assembly. The panel also has a ... Oreck XL Ultra Bagged Upright Vacuum
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum
I can smell a burning rubber type smell coming from my dc07 i. i've switched it off but what can the problem be and can I fix it myself?
More than likely it's coming from the belt in the power head. Due to some difficulty in taking the power head apart and reassembling, I do recommend taking it in to a shop. Getting the tension of the belt correctly is very important. Too tight and ... Dyson DC07i Bagless Upright Vacuum
I have an Edison dehumidifier DHE 40W G-1 and it does a good job of taking water out of the air, but it smells really bad. It is a pungent odor that comes out when it is running, not a burning smell. What is this from? Have you seen this before? Please, please help me if you can....
... Edison Vacuums
Burning smell coming out while using a Hoover's upright vaccum cleaner (model U6434900). Replaced both flat and v-belt. The problem appears to be coming from near the motor area. The manual does not provide any information on how to reach that area. Any help will be appreciated.
Took it to a manufacturer's repair center. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Burning smell coming from vacuum
Use a penny to turn the 2 screws on top a quater turn then fold down the vacuum and lift up the cover and you will have access to the belt. Clean the small hepa filter with soapy water. their may be 2 of them. The cannnister filters need to be shaken ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Burning smell using vax classic rapide
Vax dual v 124a has a burning smell
Vax mach 5 burning smell and revving loud
My mach 5 has lost suction and the brushed are spinning ... Vacuums
Burning smell coming from hoover canister windtunnel vac
... Hoover S3639 WindTunnel Bagged Canister Vacuum
Drive went out on my Hoover Steam Vac Shampooer and brushes won't turn plus there's a burning smell coming from it. Only used it 6 times - bought it in March - 2008.
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=761326\015\012Generic problem for all Vacuums\015\012Drive went out on my\015\012Posted by buster_lls o ... Vacuums
It was making a funny noise, then a burning smell, and smoke coming from under the cylinder which collects the dirt, then switched itself off. I have checked for blockages and can't see any
Your motor is burned up. stop using the vacuum immediately due to possibility of fire. this is usually caused by the inner seal on the bottom of the cyclone lifts up or gets pinched and doesnt seal with the bottom lid. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Self propel wheels not moving and smell like burning rubber coming from the back of the vacuum. How do you get to the belt to replace it?
Hello,\015\012\015\012I believe that you're asking about the Hoover Windtunnel Self-Propelled upright, but I can't be sure. I've posted a video below that we recorded showing how to replace the belts on your Hoover WT. If you have a d ... Vacuums