Having problems with your Vacuums ?

I have a Kenmore quick clean model 116.36724500 and the belt popped off so we took the bottom off and put the belt back on, but now cannot get the bottom floor plate back on! Please help! :( I have no

\015 Bottom floor plate doesn't line up right and will not go back on!\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kenmore quick clean model 116.36724500 and the belt popped off so we took the bottom off and put the belt back on, but now cannot get the bottom floor plate back on! Please help! :( I have no

... Vacuums

I have a Bissell Powersteamer Pro Deluxe, Model 8804 shampooer. I got this bright idea to take the brush off as it was full of hair and debree. Upon putting it back on it appears I'm not getting the brush on properly. Does the belt go around the end with the grooves? Also do the grooves go on the right or left side? From my view point I am looking at the machine with it lying on it's back and I am sitting on the floor looking at the bottom of machine. Sure hope I haven't confused you too m

... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help

The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Wont re-assemble I took the bottom plate off to clean out the rotary bush and can not get the plate back on! I think it is the position of the roller but no matter which way I place it when i turn it , it flicks back into the place that means i cant put the plate back on!

Assuming you did not remove the brush roller to clean it and consequently did not reseat it, I am guessing that the bottom plate is not reinstalling as it should. On some uprights, the bottom plate hooks in at the front and is latched in place with c ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Floor Attachment I took off my floor attachment, but now the belt seems to be off and I can't seem to get it back on right. I can't use the attachment and I don't know why it's so hard to figure this out. They say, just turn it to belt off, but when i turn it it lift's it up and can't line up with the belt off label. Then, when I turn it the other way, it's off. So I've been trying to pull it off so when it lines up with belt off, it's off. But the I turn it the other way and it's still off a

Try this,\015\012\015\012With the floor nozzle off the machine spin the belt lifter around until the red arrows match. If you look at the side that attaches to the vacuum you should be able to see the belt up on the hook. If is not on t ... Kirby Generation 3 Bagged Upright Vacuum

I have an old upright hoover vacuum. I need to change the belt but can't figure out how to get to it. The bottom plate over the roller brush comes off but I can't get anything else off to get to the other end of the belt.

Model no. req ... Hoover Vacuums

The belt wont turn...i cant get in to the inside to check to see if the belt isnt on the roller...how do i get up in there..i took the bottom plate off and you still cant get inside... thx Peggy

The following site has some great info on your machine:\015\012\015\012www.dysonmedic.com ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi

Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums

Belt How do you remove the bottom plate to replace the belt. I have the brush off but can't figure out how to get to the other end to loop the belt

You need to take the top cover off to get to motor shaft. Some had a couple of screws from the bottom, others had tabs, use a flat blade screwdriver to fit into the slots at the bottom edge of the top, pry out and up to pop the cover off. ... Hoover Commercial C1403 Bagged Upright Vacuum

I cannot find how to get bottm plate off to replace sweeper belt. where do you change the belt?

There are 3 screws on the top housing, one on the front Right, Front Left and behind the hose in the back ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.

Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums

We had to take the bottom of the vacuum apart to remove dirt that had plugged the hose. We cannot put it back together so that the smaller round belt stays tight. I need a diagram of how this belt is supposed to fit.

Most vacuum manufacturers avoid putting their shop manual in the public domain. There are various reasons for this, some good ones.\015\012But I did find this. Maybe it'll help.\015\012 ... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

The TechDrive Pedal on my Kirby G6 fell out of the back of my vacuum cleaner. I removed the screws from the metal plate one the bottom to try to see if something had come a loose. Can you send me a diagram so I can put it back together or tell me where I can get a service manual. The only part I am having trouble with is the metal piece inside that engages the power drive. Thank you.

The pedal drive fell out . Do you have a manual telling me how to get it together again.. Thanks, Dianne ... Kirby G6 Bagged Upright Vacuum

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems

Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

My Little Green Machine has stopped sucking (second one with this problem!) I have removed the bottom plate and cannot find how to get to the hose to determine if there is a blockage. How do I do this? There is a screw that seems to hold a piece in place but it does not come out to get access to the hose.

Remanufacturing is a big problem since we don't know what was changed and how. ... Bissell Vacuums

Hoover 2000W dust manager cyclone- Have had this for about 2 months and the brushes stopped turning thinking that the belt had acme off turned it over to try to get in to look at belt now the bottom wheels have came off and will not go back on have not lost any bits literally just undid one screw! Please help!

... Hoover Vacuums

Hoover self-propelled windtunnel U6430-900 flat belt gets hot & becomes hard to push. It has a filter bag. Purchased 8/2/01. Took one plate off bottom. Used a compressor to blow out dirt & dust. Put new thin belt on.

Belts get hot when fibers from carpet get wound arounf the belts mounting shaft. Best to take a razor and cut off any fibers so the belt doesn't get hot again ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Cant get the bottom plate back onto my dyson upright DCO7i

You need to press hard and turn till they lock inhttp://www.youtube.com/watch?v=fN8k--LbuCs ... Vacuums

I have a Dirt Devil Vision and when I put a clean canister back in place the suction at the bottom of the filter clogs up and very rarely go into the canister. Also where the air blows out of the motor, I will get particals that will blow out. I have checked where the belt is and also the suction tube. Do you have any ideas how to fix this problem?

Yes your intake hose is clogged thats the clear hose you can see it on the bottom from the back.disconnect the upper hose from your intake hose and try to push a coat hanger through with the end of the coat hangers end bent till its rounded so you do ... Dirt Devil M086700 Vision Bagless Upright Vacuum

Kenmore canister model numer 26212690 12.0 amps with powermate. How do you remove the bottom part to check the belt. The blade won't turn and the switich is on rug not wood floor. There are two arrows that say to seperate use screwdriver at arrow. Have seperated at the arrows but the back will not come apart.

Hi There,\015\012\015\012There are actually two screws that need to be removed before you can separate the bottom from the top housing. The screws are actually located either underneath of the headlight cover, or on the bottom of the ma ... Kenmore Vacuums

After replacing the belt on the powerhead we cannot get it back together any help would be appreciated

Http://www.manualshark.com/s/%22electrolux+guardian%22/page:6 ... Electrolux Guardian Bagged Canister Vacuum

I have a proheat carpet cleaner model 3 7901. the problem is the brush on the bottom of the machine plus the two end parts and the belt came out. i put everything back but they popped out, they are not staying in place. what am i doing wrong or what do i have to take out to get everything in place correctly?

Hi\015\012\015\0121. You’ll need to follow this procedure to assemble your unit back together.\015\0122. Make sure the foot pedal is in the proper position.\015\0123. The SmartMix should be properly loaded into the main ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I replaced a torn belt and now cannot get brush back in place

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=555430\015\012Generic problem for all Vacuums\015\012I replaced a torn belt\015\012Posted by brendais on Apr 29, ... Vacuums

I have a Bissell 1694. I purchased a new pump and belt. The machine came apart very easy, but I cannot get it back together. The hoses don't all have a place to go or something

Don't know if this will help you out or not. it is for a different model, but the hose layout is about the same.\015\012\015\012 ... Bissell Vacuums

I cannot get the belt back onto my G4 Kirby vacuum

Remove the brush assembly and it will go on easy.clips on side ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0749 seconds