Having problems with your Vacuums ?

Need to replace cord on a EL8807 Can't get it apart


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need to replace cord on a EL8807 Can't get it apart


... Vacuums

I need to replace the cord on an older Hoover upright, model S660, about 1986 vintage. The cord broke where it enters handle. Handle comes apart easily. Just not sure how to pop the switch out without breaking it. Was looking for a manual online to see parts diagram and/or instruction on disassembly and cant seem to find one for that old of vacuum.


Check ebay. those vacuums are worth fixing. I loved them. they would **** the carpet off of the floor! those cords aren't hard to replace.just remember the way you got the old one out. ... Vacuums

Cord replacement I need to replace a damaged cord (the reel works). How do I get the top off so I can remove the back end? Once I get it off, will I be able to change the cord, or do I need to buy the whole reel assembly? (and thanks for the help - I love this site!)


You will probably have to replace the whole reel cord. Depending on your model, on each side, there is a bar in the middle that will slide off, then the 2 halfs will come apart. They will only slide in one direction. If an older model, there are s ... Electrolux Lux 5500 Canister Vacuum

Need to replace electrical cord on a dirt devil breeze. i cant get the whels off to seperate the 2 sides??


... Dirt Devil Vacuums

I need to replace the cord on the beater brush attachement for s3614 hoover powermax.. can't find parts. I was able to pull apart the brusher, but I cannot release the wire to resplice and reconne


... Hoover S3614 Vacuum

I need to replace electrical cord on hoover windtunnel UH70120. How do i get the cord reel off? Can i open the cord reel to replace the cord?


... Hoover Company Wind Tunnel U53019 Upright Vacuum

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.


Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.


Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums

The power cord on a flat iron broke/got chewed through and needs to be replaced. how can I open it to get at the cord or fix the cord?


... Vacuums

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating


... Vacuums

Need parts diagram for euro-Pro ep601. I need to replace the power cord, but cannot get the motor gasket guard off.


Hi!You need to release a "clip" under the handle(this is on top of the dust cup) and then look for a hidden screw right under the thermostat label. ... Vacuums

Dead motor I purchased a new motor for my Dyson Animal but I cannot figure out how to get the thing apart to replace it. There are weird star shaped screws but I can't even see how removing those would get me where i need to be. HELP!!!


Ace Hardware or Home Depot should have your star screws ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

How do you get it apart to replace the power cord


How to wire the new power cord into motor ... Hoover U5399-900 WindTunnel Lite Upright Vacuum

Need to replace power cord


Here are the Sears links to purchase both the part and the manual.\015\012\015\012http://www.searspartsdirect.com/partsdirect/searchByPartDescAction!searchByPartDescription.pd?brandId=0582&productCategoryId=0645000&modelNumber=116339223 ... Kenmore 22612 Bagged Canister Vacuum

Need to replace cord on hoover u5720


Un do all screws on back of vac replace cord screw back together ... Hoover U5720-900 WindTunnel Upright Vacuum

I have a Dirt Devil Upright Vacuum Model 088525B. I need to replace the power cord. How do I take the vacuum apart?


... Dirt Devil Vacuums

Took canister apart to replace power cord. some grid fell out before i could see where it was. need to know where it goes


... Oreck BB2000 XL Little Hero Canister Vacuum

Where can I get a parts list for the miele s514? I need to replace the power cord assembly.


... Miele Vacuums

Can i fix a chewed apart cor on a vaccum cleaner or do i need to replace cord


Fix it!! with it unplugged, strip both ends of the chewed area to bare wire and then splice them back together. Wrap the splice with electrical tape! ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I need to replace the power cord on my Eureka 2271, and would like know how to get into the connections?


... Eureka 2271 Bagged Upright Vacuum

Need to replace cord rewinder on electrolux tank vacuum cleaner. How does the canister come apart?


If it's the older style open front and the two rubber strips on each side slide out. this should help you along. ... Vacuums

I bought new belts to replace the old ones (one had broken and the water would not feed) My cousin took it apart and now I need to put the new belts on and get it back together - do you have instructions or a diagram?


There are different variations with Bissell. They have the ProHeat series and a Power Turbo series. Below is a link with instructions and diagrams for the Belt Access Door. If this doesn't solve your problem or isn't the correct model, please post ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I am trying to replace the power cord for my 82 year old father-in-law's Oreck XL 2600HH. He already took it apart. I need to know where the semi U shaped spring steel piece is supposed to go inside the Helping Hand Handle? Any drawings or schematics available? Thank you for your time. Arthur


That justs lies on the inner handle whenb you put the spring back. There should be two holds where each end of the spring sits in. ... Oreck XL Ultra Bagged Upright Vacuum

I have a shark vacum cleaner model sv736k 15.6v handheld and the charger cord shorted and corroded the contact. I need a replacement charger ka12d240015033u where / how can i get one?


... Vacuums

Need to replace powerhead belt in sears canister vac - cannot get head apart - plz advise


If you press on either side of the raised top light cover it will come off. Then you will be able to see the light bulb and two screw heads. Remove the two screws and the top cover of the\015\012power brush will lift off and you will be able to acces ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0761 seconds