Having problems with your Vacuums ?

Argos VU-01 bagless vacuum set up - Vacuums


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Argos VU-01 bagless vacuum set up - Vacuums


... Vacuums

My Kenmore bagless intelliclean vacuum is making a loud noise mainly when it is vacuuming on the highest setting (when the light is red). We have taken it apart and cannot find a clog. It has also lost suction.


This might help, it was posted on a previous problem but is the same issue you are having it seems: "Here is a possible solution. If the v ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Vacuum shut off with power cord in an active wall outlet. It was loaded with dust/dirt in the bagless cup. Is their a re-set proceedure?


There is a thermal overload switch in the motor. It should reset itself. Let it cool down for a while. And it should start again. ... GE 106585 Upright Vacuum

How do I change the setting on the capture bagless vacuum from hose to floor?


-Pull out your hose from the hose port, and it should be ready to go. If it is not sucking, then perhaps you have an obstruction in you hose. On the back of the cleaner where the hose attaches, you can squeeze the two tabs and the hose will release ... Eureka 12 Amp Capture Vacuum Upright Vacuum

I recently purchased this vacuum after reading consumer reports article on it and from recommendations from family. However, since I've had this vacuum it's been nothing but problems! I have a frieze carpet and I have the vacuum set on the highest setting. Each time I use it, the vacuum clogs with carpet fibers before I even finish a room! Any suggestions?


Is that a shag carpet? the power head is raised up all the way can you lower the suction on it is the carpet old the vacuum may not be able to handle the carpet,go to a vacuum store and see if you can try somthing else out some stores well let you re ... Hoover Tempo Widepath Upright Vacuum - Blue

Levels/Settings I am having trouble changing the setting on my vacuum from 1 or "Low, Hard Surface" to any other setting. Without changing it, I am unable to vacuum on my carpet, since the setting is too low.


These height adjustments are designed so that they will not adjust when the handle is in the "back" position. This is so they will stay where they are set and not self-adjust while you are vacuuming. To change the setting, you need to return the hand ... Hoover Elite Rewind Bagless Upright VacuumVacuum

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?


This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

On/Off switch. When the switch is set to "Floor" setting the vacuum will not turn on. When the switch is moved to "carpet" setting the vacuum starts.


Because floor means for lanolium it may have a sensor that detects carpet or linolium ... Kenmore 35821 Vacuum

When I sart to run my bagless vacuum, it runs for a second and then shuts off. I replaced the belt and the filter. The repairman told me that on bagless vaccuums, the motor and bearings get clogged w


Take the brush roller off and on the ends are the bearing caps.try to take those off and clean the bearings ,carpet strands and hair will cause that.after you do that make sure the roller turns freely if not then the bearings might be bad and if that ... Vacuums

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

DIRT DEVIL VACUUM 4 MONTH OLD AND HOSE SPLIT TOOK BACK TO ARGOS TRIED TO INFER IT WAS MY FAULT ENYONE HAD THIS PROBLEM ? THE STRETCH HOSE SPLIT AND I HAVE NOT HAD THIS HAPPEN WITH ENY OTHER CLEANER THE SALES GIRL IN ARGOS SAYS THIS WAS MY FAULT . DIRT DEVIL VACUUM DDCYLBG5 BAGGED CYLINDER G TABERN.


From the Argos website... they must repair or replace or refund, up to 1 year. The squeaky wheel gets the grease, go over her head.\015\012 \015\012If there's a fault with the product...\015\012We've made it easier!\015\012 ... Vacuums

Pelacing hoover bagless nano vacuum belt - Bissell 3576 CleanView II Bagless Upright Vacuum


... Bissell 3576 CleanView II Bagless Upright Vacuum

I have a Dyson bagless Animal vacuum and I can't get it to go in the position needed to vacuum. I was vacuuming, then took the attachment out to do the edges and when I replaced it, the unit would


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

AEG T7 Vacuum Bagless Vacuum Cleaner Manual - Vacuums


... Vacuums

Bissell 37604 Bagless Upright Vacuum. Hose keeps clogging every time I vacuum. Is there a way to prevent this? I am ready to buy a new vacuum, but it does do a great job picking up hair...until it clogs. It clogs at top of hose. Could the hose be kinked? It does not look like it.


That is a defect in the design of that style of vacuum. I went back to my old vac because I got so tired of having to unstop it. The sharp turns in the hose and the molded plastic causes it. Find one without the turns. ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

Every time I try to vacuum my apartment with my Dirt Devil Featherlite bagless vacuum, it shuts off before I have finished one or two rooms. I then have to wait 30 minutes before continuing. I had the vacuum for 2 months before exchanging it and it is doing the same thing with my new one. It seems to happen after the first time I empty the cannister. Any ideas?


Your motor in the vacum is getting hot.Thats why it shuts off.Its fitted with a shut off switch to stop you doing any damage to it.1 The reason for getting to hot is that you are filling the cannister to full.Try emptying it half.good luck. ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

Dyson vacuum turned off while vacuuming - Dyson DC07 Bagless Upright Cyclonic Vacuum


Hi There, Assuming if you leave it for an hour and come back to it that it works again you have an airflow issue. This machine will cut out if the motor gets too hot. The likely causes are 1. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hello! I have a Kenmore Progressive bagless vacuum with the Easy Clean extended life filter. The model number on my vacuum is 34728401. I was vacuuming the carpet when it just stopped running. The dirt sensor light will come on, but nothing else. The belt looks fine, and I don't see anything keeping the beaters from rotating. Help Please!!!


You can have power to the dirt light sensor, but it seems like the motor itself is not using the power supplied. ... Vacuums

Vacuum getting hot in filter area - Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum


That's not abnormal, unless it's getting very hot. Have you changed the filter recently? If the filter is blocked it will get hotter than normal. the filter should be changed every 4 to six weeks of normal usage. ... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

My kenmore premalite vacuums wheels pop off - LG Electronics Premalite Vacuum Bagless Cyclonic Vacuum


... LG Electronics Premalite Vacuum Bagless Cyclonic Vacuum

My DC07 Animal Bagless Upright Cyclonic Vacuum has a small attachment for vacuuming carpeted stairs. This attachment is currently not spinning its internal brush necessary to pickup the dirt on the stairs. The rest of the vaccum is working fine. The suction cap on this attachment is pulled out, as it should be. I have checked the vacuum over thoroguhly and there are no bloackages anywhere.


Make sure to extend the wand straight up and completely out of the handle and watch that you don't kink the hose. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Eureka 2961 avz bagless vacuum with no sucktion


I would recommend either replacing the main suction motor or replacing the vacuum cleaner all together. Eureka makes a cheap vacuum. You should consider upgrading to a better brand such as electrolux or hoover. ... Eureka 2961AVZ Bagless Upright Vacuum

Hoove Cyclonic Bagless vacuum shuts off after only a few minutes


The motor has a protective overload cutout device to stop it from over heating - this can be caused by a blockage of some sort in the hose or brushroll compartment or blocked filters.\015\012After checking the above and it still cuts out, tak ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Cut off while vacuuming - Eureka 4700A Maxima Bagless Upright Vacuum


If it went dead, and restarted after it cooled off, then check for a clog in the hose or the dirt inlet by the brush roll. If it won't turn on, you could have a bad switch, cord, motor or a bad electrical connection. ... Eureka 4700A Maxima Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0650 seconds