Having problems with your Vacuums ?

I lost all suction on my vax 6131 and took the VAX Combination Floor Tool to bits, trouble is i cant put it back , is there instructions or can anyone help me


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I lost all suction on my vax 6131 and took the VAX Combination Floor Tool to bits, trouble is i cant put it back , is there instructions or can anyone help me


... Vacuums

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.


Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums

It's been awhile since I have used my shampoo system on my Ultimate G series Kirby. Well, as instructed I took it apart and cleaned it. Now I can?t figure out where to put the ?screen cap? and ?sponge filter?. I have my manual in front of me and the only place it shows the filter and sponge (page 35 in the manual) is when it?s been taken apart to clean. It doesn?t show where to put it back. I don?t know what I would do without all the pictures in the Kirby manual. HELP! Thanx. Visual Kirby Vacuu


Hello,\015\012The littlew round screen goes in the hole where the hose attaches to the tank. The round foam filter goes up in the hole underneath the on/off valve for the foam. Here is a guide if you need any more help...\015\012\01 ... Kirby G6 Bagged Upright Vacuum

I have a Diablo wall switch timer that was manufactured in 1982. It has 926Z on the back. If that is not the model number, I am in trouble. I have lost the operating instructions. Can you help?


Guess we'll just have to give up and throw this away....I've been holding on to one for 30 years, and I remember it being difficult to program anyway.... ... Vacuums

Belts I have recently bought new belts and when I installed the green light only comes on sometimes and I can smell rubber burning. The last belt broke very quickly so I am assuming that when I put the vacuum back together I am doing something incorrectly. Can you help instruct me?


Recently received a kirby from mother in law and don't how to change the belts ... Kirby Ultimate G Bagged Upright Vacuum

I have a Swan Petmaster 1800w Hepa Filtration hoover s/r no SU3021 and cant find my instruction manuel. Problem is when on hoover it doesnt seem to be sucking anything up?? I have cleaned the cylinder and filters. Is it something to do with the bit that you can use to clear stairs/car etc and not converting back to an upright hoover again? Please help Julie


... Vacuums

Neighbor took apart his nv22 and cant put it back together im trying to help


... Shark Helmet NV22L Shark Navigator Upright Bagless Vacuum

The back wheel came off and i went to put it back on and the other wheel that connects to the mechinism/gear height ajustment that goes up/down with a spring in it came off as well. i have been looking for a schematic to put it back together but cant find any.


You do not need schematics, it is fairly easy. Clean and lubricate the teeth on the inside of the front wheel shaft assembly. Insert the spring into small pedal and place the pedal designated opening on the Kirby front fan casing with teeth facing ou ... Kirby G6 Bagged Upright Vacuum

Cant put the roller back on right!


The user manual has a diagram and instructions and is available online.\015\012I could try to walk you through but their diagrams and instructions are pretty good.\015\012A couple tips....the small red plate screws in laying flat and the ... Bissell 8910 ProHeat Clear View Upright Vacuum

Hi I have an electrolux "The Boss" hand held vaccum cleaner. I cannot find the instructions and am having problems changing the belt. It is model number Z57A. Product Number 900-250-006. It is the first time I have had a problem. I only use it occasionally for my caravan. So cant find the instructions and cant remember how to change the belt. Please help


You need top lace belt on brush roller and re[-assemble by putting plastic cover on which is retained by 2 recessed philips screws.. Prize off triangular coverat fornt.behing that you should see the belt lying loose.You need to get a blunt object to ... Electrolux Vacuums

I HAVE A BISSELL PROHEAT CARPET CLEANER I DISSEMBLY IT TO CLEAN IT. I DON'T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT'S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON'T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT'S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have a kirby sentria. vacuumed up my son's headphones and immediately shut if off. took brush off, unwound headphones, put it back together. when i turned it back on, the belt snapped. so i went to vacuum place, got new belt, but when i put it on, with the green arrows lined up, it doesn't have much suction. with the red arrows lined up, it just smells like its burning and i don't want to break another belt! HELP!!


Take the front off the vacuum and check inside both the front portion and the canister for additonal clogs. Sometimes something will get caught in the impellor, causing the motor to overheat. Since there's little suction and the smell, I'd guess th ... Kirby Generation 3 Bagged Upright Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.


... Windsor VS14 Versamatic Bagged Upright Vacuum

I HAVE A BISSELL PROHEAT CARPET CLEANER 7920 I DISSEMBLY IT TO CLEAN IT. I DON'T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT'S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON'T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT'S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I had to take apart hand tool for steam vac and now I cant get it back together. Please help.


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Need help putting my bissell carpet shampooer back together


The side that is dragging needs the roller that the brushes are on ,to be precisly pushed back up in it's place,it will take a few minutes and it will not slide back in place easily just use a little force as for the hose diagram, bissell.com,enter m ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Need help putting my bissell carpet shampooer back together


I don't know how to advise you on this. The Bissell is pretty complicated when you take the hood off. Under there is a number of things that must be in place correctly to replace the hood. There is a small plastic "rod" with an "o" ring on it that co ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Wont re-assemble I took the bottom plate off to clean out the rotary bush and can not get the plate back on! I think it is the position of the roller but no matter which way I place it when i turn it , it flicks back into the place that means i cant put the plate back on!


Assuming you did not remove the brush roller to clean it and consequently did not reseat it, I am guessing that the bottom plate is not reinstalling as it should. On some uprights, the bottom plate hooks in at the front and is latched in place with c ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Noise Hi... I was doing normal house work and had been using it on carpet... I put it on floor for my hardwood floors and picked up loose clean cat litter and went to put it back on carpet and it made a horrible noise like it was rubbing. cleaned the filter... cleaned the roller thingi ...checked the belt and it is still making that horrible noise. It does not make the noise when I have it on floor but as soon as I put it on carpet it screams at me. Help! Please and thanks Linda


Hi Linda,\015\012Sounds like clutch problems, try to move the lever for carpet/floor back and forth a few times maybe it will free up. If it still makes the grinding noise, the clutch assembly will have to be replaced. Let me know, i can even ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have bagless samsung air track 2000w tein cleaner vaccume cleaner..it has only one switch for on and off...cant find a switch to put the cord back????? .


... Vacuums

I have a Kenmore quick clean model 116.36724500 and the belt popped off so we took the bottom off and put the belt back on, but now cannot get the bottom floor plate back on! Please help! :( I have no


... Vacuums

How do I put it back together I took it apart to clean it. Can't get it back togather,, HELP!!!


Here is some videos that should help you ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hoover steam vac- lost instructions. Where do you put the water and cleaner and how do you put back together?


Go to www.hoover.com for the instructions/owners manual ... Vacuums

Good day, I took off the cover on a proheat upright, to install the suction diverter flap. Guy at the shop told me I had to do this but I don't think it was really necessary. Anyway, I am having a real job getting the cover back on. The shampoo mix piston seems to be causing the problem seating the two halves correctly. I see no obvious "right: way to put the piston back in. can anybody help me. Thanks Richard


Hey Richard. Turn the shampoo mix dial so the spiral is all the way at the top when you are looking at it from underneath. then, you want the piston to seat in the top groove of the knob. You want the piston's end that jets out to fit in the space ... Vacuums

I have a morphy richards upright hoover model 7333 and i cant get to the belt to see if it is either broken or just come off the runners, i have lost my instructions and cant get the things apart to have a look, does anyone know anything about these hoovers? many thanks, Carina.


... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1097 seconds