Having problems with your Vacuums ?

What's an easy way to remove per hair from car


Answers :


You can get them off ebay
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

What's an easy way to remove per hair from car


... Vacuums

I have a Panasonic MCV7515 UPRIGHT VACUUM and need to remove the cowling that covers the brushes to clean the hair out of the bearings, but it isn't clear how that can be done without a crowbar or sledgehammer. Removing all the visible screws makes the hindmost part loose, but not the front half. Also, is there an easy way to replace the belt?


... Panasonic MC-V7515 Bagged Upright Vacuum

We have a Eureka Chinese p.o.s, model 6831. The brush roller won't turn, appears to be plugged with cat hair dang long hair cat. I cannot figure out how to remove the cover without breaking it after removing the screws, there is a u shaped collar on the tube in the way. Can anybody help?


There are a couple of tabs on both sides of the top housing that need to be unlocked by using a flat screw driver, then the top will come off. The u shaped collar on the tube will then give way to take the roller brush out to clean. ... Vacuums

My dyson has started to give off an acrid smell when I use it. I have checked all areas for blockages, cleaned the removable filter and removed all hair from the brush but this has not helped. I am worried the motor is getting hot in use. Whats the best thing to do next? Thanks


... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My DC 17 is plugged. I can see through the small hole in the top blue "flower shaped" that the holes at the top of the canister are plugged with hair & dirt. I cannot see anyway to get to these small round holes. Is there a way to remove the top blue "flower shaped" piece? I have removed the inner cone from the clear canister but still cannot get up underneath.


Please kindly follow the steps below to clean your vaccum cleaner,1.) Remove the clear plastic handle. You\015\012will have to take out two screws and then unclip from the from the\015\012front. It's stiff, I gently used a flat head screw drive ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

We ran our 9 gallon Ridgid without a filter (Silly boy) Now I need clean the exhaust. The entry to which is clogged. Any easy way - without breaking it, to removed the plastic mount the filter fits on to.. ? Please.


This video may help you ... Ridgid 9 Gallon Wet/Dry Shop Vac 96882 Canister Vacuum

I was in the midst of vacuuming with my Dyson Animal when it stopped working. It smelled as though part of the motor burned up (there was hair and string wrapped around the brush so I stopped to remove it). Any ideas on an easy, quick, and inexpensive fix? Thank you!


Hi there,For guidance on clearing any remaining threads or hair from around the brushbar and resetting the machine, please follow the steps shown in the video below. Please note, the brushbar will never rotate when your machine is upright, so ... Vacuums

My floor brush stopped spinning, I cleaned everything out as per your directions in other posts and following the instructions in the manual. Now the floor brush wobbles and has a hard time spinning when upright. Looking at the end of the brush, opposite the drive belt, the bearing-type end that the brush spins on appears to be off-centered. Is there an easy way to fix this???


... Bissell 3130 Bagless Upright Vacuum

Hi, So glad I've found this site! I've attempted to remove the filter as per this post: http://www.fixya.com/support/t2784981-remove_filter_beam_model_2775 The result is that I've pulled off the finger loop because the filter was in so tightly. Please can you tell me what the best way forward from here is? Thanks, Duncan


So did the filter itself come with it, or just the finger loop broke off and the filter is stuck in there? :(Tim ... Beam Industries 2775 Serenity Plus Central System Vacuum

Kirby Heritage II. Beater bar does not turn. One end rotates freely, but the other sticks, preventing the bar from rotating. No obvious means to disassemble the end of the bar. Is there a way to repair this, or does this require replacement of the beater bar? Did clean the front end assembly, and removed all hair, threads and similar obstructions.


The bearing is bad on the end that turns hard. You will need to purchase a new brush roll assembly. If the roller is older that 4 or 5 years, it should be changed anyway. The brush strips that scrub the carpet loose their strength after many years of ... Vacuums

I have a Royal 7910 extractor and even though I vacuum before cleaning the carpet, by black cocker spaniel's hair gets pulled into the plastic pick-up attachment and I cannot find an easy way to clean it out. I have tried taking the screws out to separate the halves, but it seems as though they might be glues together. I have run water from a sink sprayer though the openings with some degree of success, but it still is pretty cruddy. I have tried snaking pipe smokers pipe cleaners up the pick


One person wrote this in a review:\015\012Most home carpet extractors are very difficult to take apart for cleaning and maintenance. The Royal 7910 is the exception. No tools are needed to take the front housing off to clean out all the pet hai ... Royal CE7910 Wet/Dry Vacuum

Is there a way to remove the brush filled with dog hair to make it easier to clean instead of just pulling out by turning upside down?


It's best to simply use a knife or razor blade to cut through the hair and clean it out that way. Taking the power head apart can easily result in more serious problems. ... Hoover Vacuums

How do I access the motor to my eureka capture? It has no suction at all but turns on just fine..filters are cleaned and there are no clogs or leaks on the hose....im thinking there must be something stuck in the motor possibly but there are soo many screws that im having trouble removing them all....whats the best way to access the motor to check it??


... Eureka Capture Upright Vacuum Vacuum

My Electrolux Aerus auto rewind chord mechanism is broken. Is there an easy way to remove the back of the canister to replace or fix the spring there?


Take out the bag and keep the door open. \015\012While the bag door is still open, turn the machine upside down so you are looking at the serial number.\015\012Pull the cord out one foot.\015\012Use a puddy knife and put it between ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Hoover hu 4207/1 pet hair removal turbo brush wont revolve


Try Larryclare1's solution for a Kenmore and see if it helps. Worked wonders for both my turbo brush attachments. http://www.fixya.com/support/t1095798-kenmore_model_116_powermate_jr_stopped ... Vacuums

Same problem removing the easy empty cup..


The dark gray plastic slide is separate from the Easy Empty Cup. Just slide the release tab all the way to open position, and then pull the Easy Empty Cup straight up.\012With a little effort, the cup will dislodge from the dark gray plastic platter. ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Oreck XL How to remove rear wheel. Removed all viewable hair, thread, etc., but one wheel is still hard to turn. I think there's hair stuck inside the wheel core. Can I remove the wheel & take it off the metal post?


You can take a medium size flathead screwdriver and slide it in beside the wheel and under the pin. Then pry carefully on one side and then the other it will start to come out but work both sides alternately so you won't put too much pressure on the ... Oreck XL2000 Bagged Upright Vacuum

My wind tunnel had a lot of dog hair at the intake hole from my renter that used it. I was able to remove it, but is it possible there is hair up inside beyond the hole & how would I remove it? it is not picking up dog hair .


I have an upright Dyson Cyclonic.  Because I have dogs, I also have a Miele Pull-along.  I use the cyclonic for fine dust after picking up the hairs with the Miele.  Much quicker in the long run.  Otherwise ... Hoover U5453-900 WindTunnel Supreme Bagged Upright Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom


Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Hoover U5111-900 that, every time I attempt to use it, shoots everything it should be sucking up, back out toward my feet. I have replaced the bag, pulled out lots of animal hair and such from the area behind the bag, and taken off all parts able to be removed without a screwdriver and pulled out all chunks of hair, dirt, etc. It still keeps shooting everything it should **** up out the back. Is there something I can remove to get the clog out if that's the problem? I'm scared I wil


Hello,\015\012\015\012Although I could not locate info on a U5111900, the link below shows a similiar upright and things to check for clogs. See page 12 and refer to the pages noted.\015\012\015\012 ... Vacuums

After removing the filter, I cannot get to battery on the Dirt Devil Kone M0213, there are two horizontal screws. Removing them does not help getting to the battery, no way to remove the insert where the battery is located.We have two of these, however they did not come with a manual for dis-assembly. Please help or proved a diagram on how to remove the battery. Many thanks, Wesley Lennon


Sheesh, did anyone actually read the person's question? It's about the battery, not the filter.\015\012\015\012You have to get the outer cover off and it's not easy. There are four tabs which need to be released. I have to use a very sha ... Dirt Devil KONE Hand Vacuum MO213BLU Vacuum

I have a Dyson DC-17 and the top of the cyclone has hair and other debris jammed in the ports. It has 6 six screws holding the parts together and I can only get access to 4 of the screws. The bottom piece appears to be removable, but I can't figure out how to remove it without damaging it. If I can get this piece off, then I have access to the other 2 screws. Can you tell me how to remove the bottom piece? Thanks in advance.


The instructions on how to dis-assemble your DC-17 are somewhat lengthy and it is quite helpful to have pictures and videos handy while you are doing it. Normally I would give the instructions here, but due to the amount of info that is necessary to ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth


When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums

I need to find a way to replace the attachment hose on this unit. the tube to spray the detergent snakes into the base next to the wheel and i'm unsure of how to take it apart without breaking it. is there a simple way to remove the wheel? do i need to do something special to replace that tube?


The best thing for that situation is to look on the side of the road and you will find a Bissel, I see one or two a week. Take one home and experiment on that one not yours. I have brought many and never have I bought one. I never see a Hoover by ... Bissell 9200 Upright Vacuum

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?


Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0423 seconds