Having problems with your Vacuums ?

Flexsteel leather recliner does not go into an upright position

\015 The recliner will not go into an upright position.\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Flexsteel leather recliner does not go into an upright position

... Vacuums

My Oreck vacuum cleaner will only stay on in the upright position. If I try to recline it to vacuum, it shuts off...put it back up and it turns back on. Of course I can't vacuum in the upright position...what do I do?

It sound as if you have a short in the cord or it has come loose from the motor you can take it part by removing the four screws in the buttom of the base plate to see if any of the wires are loose. ... Oreck Vacuums

My dyson slim vacuum doesn't switch from hose to floor mode. I thought the foot lever was broken. I realigned it but it doesn't switch now from floor mode to hose mode. I take out the hose and I can see the white part. I thought it should move as you go from upright to recline position of the handle.

The changeover valve is not activating - call the Dyson helpline - they'll set you up for a repair with a repair dealer in your area. ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

Won't recline to vacuum. Its stuck in the upright position. Is there a release somewhere?

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The suction only works when upright, when in the recline position there is no suction and it starts to smoke

You probably have suction just no aggitation. those units use a clutch assy with two belts unfortunately when the belts fail you have to replace the whole assy just like everything else on the dysons. check your brushroll for rotation and for hair wr ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

On my dyson dc 28 the carpet cleaning bar turns easily by hand, but does not turn on when the cleaner is reclined from the upright position. The white light illuminates when preseed, but the red light does not illuminate even though the motor is running. Thanks

... Dyson DC28 Animal Bagless Upright Vacuum

My Dyson DC07 will not stand upright. It just lays in the recline position.

- Stand behind the vacuum cleaner and look at the right-hand side wheel\015\012- Remove the AI PIPE (it has two purple buttons that you push together to lift it up and out - it looks like a Tuba)\015\012- Lay the handle down and look for ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC14 Animal Vacuum - Loses suction in the reclined position. Works fine upright with the wand. Any idea what the problem is? Thanks

Check the brush bar is turned on, read this article: DC14 clutch and brushbar\015\012\015\012Then check the small h ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?

Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Vacuum won't **** in upright position, but there is suction from the hose in the upright position

Theres a knob that switches it from floors to carpet turn the to floors.please leave feedback ... Vacuums

My 9 year old Sebo X4 will not stay in the upright position. The foot pedal no longer springs back to hold the machine in the upright position. Has a spring broken? Which part needs replacing?

... Sebo X4 Bagged Upright Vacuum

Miele s7000 I clicked my upright into sitting position and accidently bumped the foot release knob. The body fell back and now I can not get it to click back into upright sitting position. Something is now in the way of it locking into place. This happened last year and it was under warranty. it no longer is and I would like to be able to fix it myself in the future. Can you help me? Thank you. Kacee in Oregon

... Vacuums

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old

Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My Dyson upright suddenly won't stay in the upright position. It appears that a little rubber piece has fallen out of position.

- Stand behind the vacuum cleaner and look at the right-hand side wheel\015\012- Remove the AI PIPE (it has two purple buttons that you push together to lift it up and out - it looks like a Tuba)\015\012- Lay the handle down and look for ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Hoover Z 400 collapsible vacuum won't lock in the upright position. I pull the pin to change from a cannister to an upright, but the unit won't lock into position

This just happened to me. i took the vacuum completely apart and found that there is a locking plastic "tooth". this had snapped off but still it the track. the damage was bad but i was able to wash of all the lube off it and used a 2 part epoxy glue ... Hoover F5858-910 SteamVac Vacuum

Loss of suction when using upright. Suction remains for samll tools no suction when in upright position makes funny noise but ok when not used in that position kindest regards louis

U can remove the flexi pipe by pressing the inset button,it may be bit stiff if it had not being removed before.may be something is stuck at the bottom,also remove u bend where most of the stuff get stuck. i just posted how i fixed the suction and ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

The kick stand that lowers the vacuum when in use got in a position where the red foot pedal would not come back up to bring the wheels down and the vacuum rest in the upright position. We took it apart and corrected the position, but the side with the small circular spring came out and we are not sure how to attach it back, exactly where it hooks onto. Can you help show us where it goes?

... Dyson DC25 Animal Bagless Upright Vacuum

Brush roller does not turn off in upright position

Make sure there is not a lever to move in order to stop the brushes/agitator...\015\012if the belt makes contact with the end of the shaft the brushes will rotate...\015\012tighten all of course/and take the panel of to check behind the b ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Eureka 4870 brush won't stop turning in upright position

There will be a linkage that as come loose and not operating the limit switch to turn it off, try looking at 23. Idler Clamp Assembly on the link below. ... Eureka Smartvac 4870 Bagged Upright Vacuum

Dyson DC28 Air Muscle Vacuum that is stuck in upright position

This turns out to be an easy fix.\015\012\015\012First, get some graphite lube. \015\012\015\012Lay the vac on it's 'face'. \015\012\015\0121) On the underside of the vacuum, there is a 1/2" wide 'groove" in the ... Vacuums

Dyson won't go back into upright position to engage suction

The dyson.com website had a solution for this particular problem. Just press in a button in the area around the right wheel while lifting the rear of the vacuum up. This allows the base to roll forward enough to go back into the upright position. I ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Yellow Dyson handle stuck in down position will not click upright

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson Ball Vac won't return to upright position

... Dyson Ball DC24 Bagless Upright Vacuum

Dc07 model, cannot get it to stand fully vertical upright. It is as if something is not sliding back into position right. Don't want to force it in case something breaks. The upright of the cleaner has been dropped from time to time. Any thoughts on sorting it out?. Thanks a lot. M

Hi, Try this quick repair and see if this fixes your Dyson in terms of not going in the upright position: This is a frequent problem that we see come in on Dysons. If this doesn't fix it, please feel free to just use the clarification req ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a DC 17. In the middle of vacuuming the vacuum stopped working when it was in the upright position. It only works when the head is down and i am using the bar. I can not use the extension bar, becasue when I put the vacuum upright it shuts off. Where is the problem?

Hi there, it's Jack at Dyson.\012 \012 Like most Dyson vacuums, DC17's main suction motor is protected by a thermostat which shuts the machine down if it starts to overheat. This could be due to a blockage, and the filter may also need a wash ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0505 seconds