Having problems with your Vacuums ?

My jenome 4119 will not sew after I took out thread twisted around the inside of the thread takeup mechanism. It but will not pick up bobbin thread and if it does the stitches r inches apart or none a

\015 Thread tanghled around inside of takeup mechanism. I had to remove face plate andpull out the intangled thread. I set all dials back to original setting for straight sewing but it will not sew. will not pick up bobbin thread and when it does stiches are all over the place and skipped all together. Suggestions\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My jenome 4119 will not sew after I took out thread twisted around the inside of the thread takeup mechanism. It but will not pick up bobbin thread and if it does the stitches r inches apart or none a


... Vacuums

We have a vogue stitch janome model 539 115v sewing machine. we were trying to sew but, the thread is not picking up from the bobbin. the thread keeps breaking and we are unsure what tension setting should be used for cotton cloting. please help. thanks! tom staron


... Vacuums

Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st


Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums

I have a Singer 144w304 that I cannot get the needle thread to pick up the bobbin thread. I don't know if I am not threading the bobbin correctly out what but I had not had this problem in the past. Everything seems to be in time and set correctly but it just will not pick the bobbin thread up. What can I do?


... Singer Vacuums

While using the pin stitch , the machine has started skipping stitches, knocking loudly, the top thread is breaking, sometimes thread knots up on the underneath side. I have cleaned bobbin area, changed needle and bobbin, using quality thread, the last time I used machine worked fine, yesterday when I started sewing I had this mess HELP!


Hi,Please go through the link given bellow to have the resolution to your problem...\015\012http://sewing.about. ... Vacuums

I have a Kenmore 385.19110 model machine, and the straight and zig zag stitches work just fine, but when I follow the directions in the manual to do a satin stitch (which is use the lowest stitch length) it creates a line that isn't perfect, or uniform, and after an inch or two stops catching the bobbin underneath. Have already tried reinserting the bobbin, rethreading the machine, refilling the bobbin, changing the bobbin, cleaning the needle, changing the tension. Wondering if I just got a mac


... Vacuums

I have a Brother Nouvelle 1500S and it keeps looping the bottom stitch. I have re-threaded, re-inserted the bobbin, am using the recommended thread and changed the needle? It is still looping the bobbin side stitch?


... Vacuums

Singer 327 lower bobbin thread is wild and loopy after I sew...top stitch fine. Just changed to a large thread spool with the heavy remote base and crook to carry thread to machine and wonder if this changed tension (set at 4 and correctly threaded)? It had been working fine in zigzag but I also went back to reg foot and set stitch width at 0, center needle set. Thanks for your input and help. Deanna


... Singer Vacuums

My Kenmore sewing machine timing has gotten off. I am sewing a big upholstery project and it starting bunching thread from the bobbin. The thread is so heavy that I had to put some pressure just to get it undone. This happen a few times and then I found it wasn't sewing at all. When I evaluated without the materials in place I could see the needle would catch on the white plastic piece under the bobbin and the thread would not catch on the metal arm. It appears to be off by 1/4 - 3/8 inch.


HelloDisassemble your bobbin case which is realy quite easy, clean\015\012thoroughly with a brush and air, paying particular attention to any\015\012rust that may have formed, and any thread that may have weazeled it's\015\012way into sma ... Kenmore Vacuums

I have an expression 2038 and the stitching has suddenly changed so that the top stitching is quite good but the underneath is loose. I have the tension on 4 and have a new straight needle and good quality thread. the underneath or bobbin thread is almost not catching.


If the bobbin thread is too loose, remove the bobbin spool AND carrier.Thread the thread through the tension clip on the holder in the normal way. Hold the thread and lift it. If the bobbin slides down, tighten the small screw 1/8 turn clockwise, u ... Vacuums

I bought this machine about 3 years ago but hadn't used it due to illness. Now when I tried to sew with the Tuff Sew ,the threads continually break. If I can make about a 3 inch line of staight stitches without the top thread breaking,I consider myself fortunate The direction in the manual are extremely poor. I had to finish my project with my very old Bernina. I regret buying the Tuff Sew straight stitch. JLWebb


I do not have one but these machines require heavy duty thread...\015\012\015\012The manufacture recommends using only "#69 Bonded Nylon Thread"\015\012\015\012You should have a 18 to 20 gauge needle for that size threa ... Vacuums

Elna Corina Sewing Machine: the bobbin thread does not pick up. Someone took out the booin case from the machine, and it was never re-installed correctly. Now the thread will not pick up.


... Vacuums

My kenmore sewing machine (Model #385.11803) isn't picking up the bobbin thread. Bobbin thread case isn't turning. HELP!


... Vacuums

I have the brother Ls-2000 sewing machine i threaded the top as well as the bobbin but when i try to sew the thread gets stuck and it bunches up and tangles in the bobbin. also the little bit that did sew was tight stitches on one side of the fabric but very loose on the other side I followed the instruction and it keeps happening i need help i dont know how to fix it please help me


Adjust your tension.You probably did not wind your bobbin properly as well.Make sure you oil your machine every month or so and make sure your bobbin is seated properly before you sew.\012\012Go slower with the pressure foot speed and use the r ... Vacuums

Sewing machine won't pick up bobbin thread


Open the bobbin case and see if the hook is turning, if it is it is just a timing problem with the hook and needle, if it isn't tuning you may have a broken gear or timing belt.....It eill need to be looked at or adj by someone who repairs them....Da ... Vacuums

I have the Janome 6600 P. Beginning a seam the thread knotted and the machine made noise and needle would not move either up or down. I manually moved the needle using the handwheel and cut away the knotted thread. I began sewing again but instead of starting at the edge began about a half inch down, forward stitched, reversed to lock threads and problem repeated and received the message to "Stop for safety purposes". Did that. Referred to the manual, tried manual recommendation. Did not work. I


... Vacuums

Pfaff Creative 1459. When trying to wind a bobbin, I do what I've always done, turn the small round "wheel" on the right, slide the bobbing into the little knob that keeps it in place and gently press the foot thing on the floor that should start the bobbing to winding. The bobbin does not turn at all causing a loud whirring sound and the needle goes up and down as if it were making stitches. I finally got some thread onto the bobbin but it is not smooth and looks like a spider. I really nee


... Vacuums

I want to get my XL-5000 singer sewing machine to work. It does not sew. The top thread will not pick up the bobbin thread for one thing and the other problem is that it gives me a error message saying incomplete threading.


Check if there is any thread in the bottom bobbin and next remove it and give it a good clean in its surrounding area.Oil surrounding mechanism carefully and manually push the top needle in and watch the bobbin spinning a see if it tried to pick the ... Vacuums

** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I


You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

Upper thread of shark 803XC sewing machine will not pick up bobbin thread


... Vacuums

Top thread does not pick up bobbin thread, also clicking sound when needle is down under plate, as if it is hitting something. Please help I have a job to do! This machine is new it's a Singer Inspiration Model 4228. It worked just fine until I finished my first sewing job on this machine. I'm hoping you can help me! Thank you, CD


... Singer Vacuums

Hi I am looking for Lervia 564 sewing machine manual I was rethreading the bobbin and the casing fell out now It won't pick up the thread from the bobbin


... Vacuums

Which way is the bobbin winding when put into bobbin case > It will not pick up the top thread


... Vacuums

My sewing machine is otherwise perfect..but the stitches hv a tiny dot from the thread in the bobbin case...wat to do??


Tighten the bottom thread or loosen the top thread a little. There should be a little screw on the bobbin holder where you can adjust bottom thread tension.lp ... Vacuums

I have a futura II 920 machine and the bottom/bobbin tension is not working. no stitches are being made. i rethreaded the machine many times and adjusted top tension, still will not pick up bottom thread. we have no singer repair in our area can you help


I don't know whether I shall provide you this solution or not but the repair manual for your machine is not available. It's available for a purchase specially for fixing bobbin tension.\015\012\015\012In case you don't wish to buy it kindly ig ... Singer Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0333 seconds