Having problems with your Vacuums ?

Tecumseh starter motor 36680 brush plate and brushes

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Tecumseh starter motor 36680 brush plate and brushes

... Vacuums

Where can I order the following parts for my 1952 KENMORE SEWING MACHINE MODEL #117583, SERIAL #48054: : #5107 carbon motor brush (2) #5110 motor brush spring (2) #5111 motor brush spring cap (2) String for starter control lever Pulleys, screw and nut washer to attach string control Best sewing machine ever and still working like new, and I want to keep it that way. Thanks.

... Vacuums

I have a Electrolux , EL6988 Canister Vacum, howeveer the brushes and motor will not run when turned on. I have take the plates and cleaned around the brushes, but it will not come one. The vacum comes on but the motorized bushes do not activate. Thanks I have lost my owners manual, and have looked for the reset button and can't find or know where it is located. Any suggestions.

I need the molded wire harness inside the plastic wand ( one of the prongs is broke off) What is the part # or where can I buy it? Model EL6988 ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Hi, I have a Dyson DC04, (silver/lime) making ear popping screams! Does not happen all the time, and more noticeable when it is pulled back.The suctions not a problem and no funny smells or strange noises from the motor. Ive taken the base plate off and the belt and brush bar seem fine, but when I turn the belt, it seems to be the motor spindle thats squeaking, almost as if it need oiling, any help please

... Vacuums

I have a bosch bagless jet 12 amps/1450 W which I got secondhand. the switch to operate the powerhead (the rug brush) no longer gives me any results. I don't have the right tools to unscrew the plates and look for a belt. I don't think it's a belt problem anyway because I don't hear the powerbrush motor turn on, either.

... Bosch Vacuums

Motor doesn't run I believe it the brush on the motor. two motor brushes one is completly gone about 1/8 inch left could this be the problem.the other motor brush still has 1/2 inch left. and current to motor tested good.

Sounds like your belt slipped off. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you

Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

How to replace the motor brushes? When should the motor brushes be replaced? Where can I purchase motor brushes for Model 1500 Easy-flow?

... Easy Flo EF1500 Vacuum

Not exactly a blow gun. Convertible blower/vac - Sears Craftsman. Wire broke off ONE brush in the motor. Paid about $90 for the vac - Sears lists the WHOLE motor as one part - $88. Have requested brushes (they are provided with a lot of my 'cheap' Harbor Freight tools) but no go. Just get the canned reply - buy the whole motor. Actually got it working again... CAREFULLY drilled and tapped a 4-40 screw into the brush and soldered the lead to that... Always a way, isn't there?

... Vacuums

Brush motor does not turn. Vacuum motor works. How to replace brush motor?

... Eureka 431A Optima Bagless Upright Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

My bissell model 18Z6 has developed a loud noise and vibration when the brush is running. I have removed the brush assy and cleaned all the hair, etc but still the noise. I ran the brush motor with the belt disconnected and all seemed ok, but of course there was no load on the motor. I suspect a problem with the brush assy bearings or axle or both but I hate to just throw parts at the problem. any suggestions would be greatly appreciated.

... Bissell Vacuums

Replacing the dc17 brush motor

... Vacuums

Clarke Instructions helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? t

... Vacuums

No power when turned on, I checked motor brushes and they are almost worn out, could this be the problem? and where do I find replacement brushes? I have checked on Dirtdevil's site but I don't see any motor brushes. I am in Montreal, Canada. Thank You.

Hi,\015\012Before that I wouild check the switch...the switches on those things go bad regularly...get a meter and check the power on either side of the main switch and I think your problem will be there...\015\012\015\012heatman101 ... Dirt Devil 12 Amp HEPA Filter Vacuum Vacuum

Brushes in motor are arcing badly and motor only occasionally will start. How do i remove the motor brushes for replacement. (from the green plastic case)

This is kinda of tricky. need to know what kinda of vacuum it is first. However if you get it apart. To fix this problem the armeture brass needs to be cleaned & you should replace both carbon brushes. Should be cheap to fix if you are up to it. ... Vacuums

I snagged a loose throw rug with the Dyson last night. It jammed the brushes which stopped spinning, Once I removed all the entangled fibers the motor won't turn. The vacume still sucks, but the brushes don't spin I'm concerned I burnt up the motor for the brushes

Have you checked the belt? You can do so by removing the bottom plate from the power head. Once removed, check the belt. If broken or worn, it needs replaced.\015\012An instruction video for replacing the belt can be found on the below link. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Clarke scrubbers helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? ther

... Clarke Vacuums

Do i need to do anything special when replacing the brushes in a lamb ametek 117500 motor? It looks like I can just remove the old brushes and insert the new ones. Is it this simple? Will the motor work again? Thanks

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=758676\015\012Generic problem for all Vacuums\015\012Do I need to do\015\012Posted by edkraynak on Jul ... Vacuums

Brush motor quit. table cloth was pulled up in brush. nothing is broken motor turns free. Is there a overload fuse?

Have you checked the belt drive on the brush roller to the motor ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Shop-Vac with a 6.5 HP electric motor. The vacuum power is lacking and I think it is the electric motor brushes. Looking for the brushes. The ones I took out have the number 848 stamped on the side.

You can get them off the link belowhttp://store.advancecarbon.com/prostores/servlet/Categories ... Shop-Vac Corporation Shop-Vac 9625410 Wet/Dry Vac 22Gal 6.5 Peak Hp

Flames and fine carbon particles came out of my Dydon DC29 which also partly melted the bottom filter. The motor is still working tho. I feel that the brushes are gone. How to get to the motor and where to get new brushes???

Hi Joel,I'm sorry to hear about your experience with your DC29. We'd appreciate the opportunity to provide further assistance, so if possible, please call us on 1800 239 766. Alternatively, if you email your contact details to us at ... Dyson Vacuums

We own a dirt devil model 088600, and are experiencing a problem with the belt wearing away a section between where the belt connects to the brushes and the motor. There is a lot of plastic/rubber residue coming out from the vacuum. We have tried new belts only to find the same problem occurs. I noticed that the source of the dust is coming from the section between the brushes and motor, where there appears to be a section that is misshapen and melted. I looked up the schematic online and can't

If you are certain that the belt is seated correctly and the beater bar is nested in its holder and the cover of the assembly has been properly installed and you still see a contact area between the belt and cover, you should either: return the vac ... Dirt Devil Vacuums

Carbon brushes on ME-48 power head motor worn out. Where can I get replacement brushes? Motor is O 90197X7, Lamb, Model 118173-73 - 240V 50/60Hz

Hi Les,Most sites sell only the motor.Here's a website that includes motor brushes: http://www.kleen-ritecorp.com/search.aspx?IsSubmit=true&searchTerm=lamb+motor&gclid=CIbZ59zwiKgCFQprKgod8W2itQHope you can find the righ ... Filter Queen Vacuums

Hello can you help me please? I have a Kirby G4 vacuum cleaner, It did work ok until it started to give off burning smell and lots of sparks from the brushes. I have changed these brushes, the motor still rotates but it still gives off sparks and burning smell. Do i have to change the motor as well? Can you help please? Thankyou Martin

Some debris, even sand or dirt, probably got into the motor, causing damage to the armature. If this is the case, you will need to replace the motor. The burning smell from the motor is generally a sure sign of a bad motor. ... Kirby G4 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0782 seconds