Having problems with your Vacuums ?

I have el8802 precision vac Does it have a belt? Spindle won't spin


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have el8802 precision vac Does it have a belt? Spindle won't spin


... Vacuums

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

The brush does not spin but the belt is ok. The spindle at the inner end of the belt does not spin when the motor is running.


DC07s have two belts - one connects the output of the motor to the clutch, the other connects the clutch to the brush bar.I suspect the belt you are to refering to is the one from the bar to the brush. Unfortuenately the other belt is hidden un ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The bristles wont spin the belt seems in tact yet it wont spin


... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Bissell PowerForce Turbo: The motor spindle becomes very hot while spinning, causing the new belt to burn and break. Is this because the motor is overheating?


Something is preventing the brush roller from turning even though it seeems to be OK when not in contact with the floor. The motor shaft is spinning on one spot of the belt, causing the heating, the smell, and eventual belt failure. I have had brush ... Bissell 6594 PowerForce Bagless Upright Vacuum

Brush wont spin, belt is perfect


It sounds like the motor that spins the beater brush is burned out,If it is under a yr old it should be covered by the manufacturer warretee. Find a Hoover service center that does warrentee repairs. ... Hoover U8188-900 Bagless Upright Vacuum

I have a bissell pro heat and it wont dispense water. the little red thing wont spin and it looks like the belt doesn't move. within a few minutes you smell it getting hot.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My roller bar wont spin the belt is on though


Even though the belt is on and intact it still can be stretched and worn. If that is the case it won't be able to turn against the resistance of the carpet. Your particular model has (2) belts, a clutch belt and a drive belt. Both should be replaced ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Brush wont spin on carpet, nr. on belt YMH 29573 Where can i get speer in Sydney Australia


... Vacuums

Brushes wont spin, how do you replace belt - Bissell 9200 Upright Vacuum


Hey, sorry to hear the brushes are not turning. Here's a quick link to instructions on how to change the belt(s). We also have a terrific How-to-Video linked to this also. \015\012 ... Bissell 9200 Upright Vacuum

Brush roller not spinning. belt, spindle okay. roller taken out and cleaned, no thread. replaced but no dice. ???


Use only BISSELL Style 10 Replacement Belts (#32074) in your BISSELL PowerForce Bagless.\015\012\015\012Unplug cleaner from electrical outlet.\015\012With Rotating Floor Brush removed from vacuum clean ... Bissell 6594 PowerForce Bagless Upright Vacuum

Hoover steam cleaner spin scrub brushes wont turn cant find belt


I just brought mine home...assembled per instructions and tried all the troubleshooting thus far to no avail. So I popped off the brushes per instructions and took a screwdriver to the hole where the brushes axle inserts underneath the vacuum and tur ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Bissell proheat carpet steamer is not dispensing any liquid. The red spindle visible from top view is not spinning and the belts appear to be in tact. Can you tell me what's wrong?


Does liquit squirt out of hose, if it does, the heater inside the handle asm. may be clogged. If not, then is the pump belt ok, is the gasket on the bottom of the tank(on the vavle) on or is it sitting in the hole or missing? It needs to be on the ... Vacuums

The suction on my oreck is good and my belts are fine, brush is spinning, but wont pick up anything when I vacuum. Help?


Sounds like a full bag or an obstructed passage ... Oreck XL Ultra Bagged Upright Vacuum

The bar that the belt sits on wont spin and smells like its burning when you turn it on. Is the motor out?


Hi,No, it is not the motor, it is a bad belt or something is jammed causing the belt to slip...\012Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Suction works but rotor wont spin. belt is new and connected. was vacuuming and it pulled a piece of clothing into the machine and I heard a snap or pop.


Try pressing the reset for the brushroll motor on the top of the brush head. also make sure the brush switch is engaged and stays in the on position. switches on these always go bad. start with the reset though thats probably what happened. If that d ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?


Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

Changed belt in hoover windtunnel t-series not beater bar wont spin when vacumming


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

THE BRUSH WONT SPIN ON THE BOTTOM BUT THE BELT IS NOT BROKEN


If the belt that drives the brush is not broken, check to see if the brush itself is stuck from turning.\015\012If is is, remove it and clean as best you can, paying special attention to the two ends. It might make sense to spray the hard rubber hol ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Brushes wont spin ,even though the belt is intact


The belt can develop a worn spot. It will be intact but not spin. Replace the belt and make and remove any hair or other garbage from around the ends of the brush bar. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

Brush wont spin


Was the belt worn or broken? It probably needs to be replaced. Here is the belt you need:Dyson DC07 Belt ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Eureka Maxima isn't working right. The belt is spinning fine until I lower the handle to start to vacuum and then the belt stops spinning. As soon as I put the handle back in the upright position the belt spins again.


Sounds like belt is worn try changing belt. ... Eureka 4700A Maxima Bagless Upright Vacuum

I have a Eureka 5902AVZ and the brushroll does not work. when i remove the belt, which is not torn nor worn out, the motor spins perfectly fine. Though when i put the brushroll back into place, it shows that the motor is trying to spin, but with resistance. it seems the brushroll will not spin if locked into place, because there is no attachment on the left side of the brushroll that will allow it to spin freely with the belt. am I missing some parts or is there something else wrong?


Hi and welcome to Fixya. I am Kelly. \015\012\015\012You have correctly identified the problem as the brush roll itself. \015\012\015\012There is a bearing under each end cap of the brush roll. You can gain access to the ... Eureka 5902AVZ Bagless Upright Vacuum

Altima brush not spinning even after replacing with new belt


Take out bar :use pliers on the side of the bar :sounds like its not rotating/locked up :the holders should rotate freely if not replace the bar. ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0722 seconds