Having problems with your Vacuums ?

Do you have to remove the brush bar for hard wood floors rather than press the button?

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Do you have to remove the brush bar for hard wood floors rather than press the button?

... Vacuums

Just purchased this Dyson dc24 today. brush doesn't spin after gettin tangled in a cord. removed the cord from the brush OK. I have several times: removed the brush and replaced it OK. pushed the red button by the brush. pressed the brush power switch.

When you removed the brush roller dod you examine the end of the actual roller that is opposite from the removal opening. There is a gear that the roller fits over that may have gotten stripped when it became tangled. Check that the gear has not roun ... Dyson Ball DC24 Bagless Upright Vacuum

My Roomba stops within a few minutes of starting it and when I press the button, it says "Remove and Clean Roomba's Brushes." I have removed the brushes and cleaned them thoroughly, but within a few minutes, it stops again and says the same thing.

Hi,Accumulation of hair, dust and dirt in the Gearbox that prevents normal operation of the brushes. As a result, a power output is required to keep the brushes turning. As turning the brushes requires too much power, it con ... iRobot Roomba 4210 Bagless Robotic Vacuum

Brushes won't turn remain motionless as if cleaning hard floors even though button depressed could it be a problem with the brushes or button still under guarantee

There is a re-set button located on the brush head on the left side as viewed if you are standing directly behind the vacuum cleaner. It is black in color and is recessed slightly into the cover of the brush cover. It is round and about the size of t ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

I have a Dyson DC17 that has started making a loud noise when on carpet when the brush is engaged but not on hard wood when the brush is not turning. I have remove all the material (hair,lint, etc.) wrapped around the brush itself, but it is still making the noise

You need to replace the belt. Here is the belt you need and a manual you can view which has instructions:\015\012\015\012Dyson DC17 Belt and Manual ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Our Electrolux canister vacuum just stopped working when we were vacuuming the floor. The power does come on when the power head is attached but as soon as the power head is removed the power shuts off. I tried pressing the reset button but that doesn't help. Is there a solution that I can try at home?

Sound like you problem is in the connection going to the power head you will see a small screw on the power nozzel where it joins to the handle take out the screw and take it a part you will see where one of the bars have been disconnect from the pow ... Electrolux Guardian Bagged Canister Vacuum

My Kenmore canister model (116) 26212601 works in hard-surface mode (basic suction), but the brush won't spin for carpets, and when I try to turn it on, it makes a whiny sound and then turns off as it does when I need to press the overload button. I looked inside a bit, and the belt isn't broken--it seems fine. So not sure what the problem is. Thanks for any help.

... Kenmore 27815 Bagged Canister Vacuum

My Electrolux Epic 6500 SR will not turn off by pressing on the switch button. I took it apart and removed the switch assy. I can maunually turn it off & on by pressing the rocker arm on the switch assy. It appears that the problem is with the big blue operator button, not the switch assy itself. The button does not seem to press down enough to cause the rocker arm to switch. The button has a "U" shaped wire that presses on the rocker arm and it may have some broken plastic details at the b

WOW !!! Finally You are dead on, absolutely 100%.... good work!!!.Get only a genuine new switch button with spring from an AERUS Electrolux dealer and reinstall. Then carefully reassemble the entire body and wiring harness.Con ... Electrolux Epic 6500 Vacuum

Power nozzle on E-series won't start when cold unless the red 'reset' button is pressed multiple times while also holding the trigger to 'warm it up'...this is w/the power nozzle off the floor - no restriction on it turning. Once it's been running and then turned off the button must be pressed w/the trigger to get it to run - again w/the nozzle off the floor. It also seems to shut off too easily while vacuuming. I replaced the motor,which didn't fix it. Is the reset switch next on my list? T

... Rainbow E series Canister Wet/Dry Vacuum

My floor brush stopped spinning, I cleaned everything out as per your directions in other posts and following the instructions in the manual. Now the floor brush wobbles and has a hard time spinning when upright. Looking at the end of the brush, opposite the drive belt, the bearing-type end that the brush spins on appears to be off-centered. Is there an easy way to fix this???

... Bissell 3130 Bagless Upright Vacuum

I live in Mexico and have a Electrolux Easy Box Vacuum...I am looking for a hard floor brush that will fit the hose as my old Sears brushes are a little too small.This model is bagless and may only be sold here,but I do not care for the floor/rug brush combo brush as it does not clean tile floors very well.I would order and have a friend in the states bring to me.Thank you,Linda Staton Cozumel Mexico

... Electrolux Vacuums

Miele, Flamenco II. 2 probs. 1. the head brush is not turning when I put it on the floor. If I pick it up to look inside...the brush is spinning fast..I put it down on the floor...the head does not spin at all. 2. The suction power has dropped significantly. The suction used to be so intense, the head would **** itself to my floor and hold on...now, hardly any suction at all.

Sounds like the belt is not on correctly on the beater brush or the belt is worned out now for the suction check filters or bags that need to be empty or clean ... Miele Vacuums

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help

The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Eureka Mega Boss Central Vac Model # CV1801P. The suction works when the handle button is pushed left (floor mode) but no suction happens when the button is pushed right. When the floor attachment is hooked up and the button is pushed right, the brush rotates, but there is no suction.

... Eureka Vacuums

I've just purchased a Bosch BX1 1600 vacuum cleaner in Spain, and already I've lost the hard furnishing brush, the crevice nozzle, the upholstery nozzle, and the hard-floor brush that I think were in the box. Is there a place to purchase these separately? Thanks, Dave Wass

Hi Dave,Are you in the USA? If you are, try this web address: >>>> http://www.bosch-eshop.com/eshop/bosch/us/brushesfloortools.htm Copy and paste the address into your browser and the tool page will open up for you.Should you ... Bosch Vacuums

My roomba goes round in circles. sometimes it stops and moves a centimeter backwards and then again it goes round in circles. if you press the ,,dock'' button it goes back to the station. if you press the ,,clean'' button, again, it goes round in circles.... the machine is cleaned, the sensors aren't covered with dirt, the weels and brushes can rotate freely.... can anybody help me??? thanks in advance franz

Here's the link. IR Bump Sensor Fix ... iRobot Roomba 560 Robotic Vacuum

The brush won't stop when selecting hard floor

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Bissell Lift-off Revolution Turbo vacuum and the brush doesn't spin on its own anymore. Does this mean the motor is busted because there's no noise when you press the brush button. We've just replaced the belt, hepa filter and a new brush. But its still the same. What's wrong with my vacuum?

Its probably the motor. remove the covers with a #2 phillips head screwdriver and cut the wires to the motor ( unplugged ). purchase some crimps at radio shack to resplice the wires together in the same fashion. ... Bissell Vacuums

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.

... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

My Electrolux Regency Series upright vacuum brush motor does not activate. Cleaned the brush and press reset to no avail. Opened handle switch assembly and checked each wire attached to all three switch settings. Tried disassembling brush assembly but could not pry open after removing all screws.

... Electrolux Vacuums

Dyson 23 Animal keeps putting itself in floor mode, when I press the button to change to carpet it turns itself back to floor mode

Make it impossible for it to turn back into flor mode ... Vacuums

I have a Dyson vacuum cleaner ...upright....all of a sudden my vacuum started making this awful sound...like a loud buzz...but only when I have it on carpet....when I have it on "floor" mode it's fine....sometimes(although seldom) it has worked without buzzing...and it's LOUD!!....I have only had this vacuum for a year....and no...I have never picked up any coins or hard stuff.only use it for 2 rooms.the rest of the house is wood floors.......what shall I do? Thanks......Gloria

It may just be, that on carbet the brushes make noise that you dont hear on woodfloors.\015\012If there is a hights adjustment, set it higher for shaggy carpet and lower for berber. ... Vacuums

Can I use my ultra lix 2000 to vaccum my new ceramic tile and wood floors? It so how do you stop the beater brushes from turning so that they do not scratch the floor?

Yes you can, just set the height at maximum. ... Electrolux UltraLux 2000 Bagged Canister Vacuum

My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.

When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

I unscrewed the roller brush protective cover and removed the brush to clean it. Now the roller won't turn because the drive shaft is not turning. Is there a reset button or something?

I looked at the pictorial of this vacuum at this URL:\015\012http://middleeasten.bissell.com/images/UserGuides/3750.pdf\015\012\015\012This shows the belt to slide on the motor drive pulley and also on the brush. If the brush is bound up on th ... Bissell 3750 Lift Off Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1034 seconds