Having problems with your Vacuums ?
Irobot verro 500 stoped working - Vacuums
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Irobot verro 500 stoped working - Vacuums
My robot will not charge. Tried multiple resets and new battery from irobot.com (both suggested by Irobot customer service) but got nowhere. The vacuum did work for a short time (until the new partially charged battery ran out). If I bypass the internal charging circuits and charge directly from the charger (with jumpers) the robot seems to work fine. Unfortunatey, there is no mechanism to turn off the charge cycle, so this is not practical.
Replace the battery charger ... iRobot Roomba 4210 Bagless Robotic Vacuum
IRobot Roomba 550 vacuum not working.
... iRobot Roomba 550 Vacuum
Rollers not working - iRobot Roomba 530 Robotic Vacuum
Wbtcht,\015\012\015\012remove and clean the brush bearings. Run the Roomba without the dustbin, and see if the brush turns while the unit is on. If not, it's time to call support.\015\012\015\012Fembot ... iRobot Roomba 530 Robotic Vacuum
I have a iRobot 4150 and have recently experiencing performance issues with the vacuum. Recently, it started stopping about a minute after you turn it on. I thought maybe the battery was the issue, but I bought a replacement. It has worked well for the past 6 months. While it's running it sounds like it is going to die, even though it is fully charged. Any ideas?
Yes, a common issue with the cleaning head module, chm. You will need to diassemble the Roomba and remove all debris from the CHM. Also take a look in its gear box. ... iRobot 4150 Roomba Vacuum
The boiler stoped working on my eco pro 3300 - Polti Eco Pro 3000 Canister Steam Vacuum
There is a high possibility that the boiler has build up of minerals and requires cleaning. I suggest using a product called KalStop to remove the calcium buildup that is cause by leaving water in the tank for long period of time. ... Polti Eco Pro 3000 Canister Steam Vacuum
Roomba water not working - iRobot Roomba Discovery SE Bagless Robotic Vacuum
... iRobot Roomba Discovery SE Bagless Robotic Vacuum
Spinner not properly working - iRobot Roomba 560 Robotic Vacuum
... iRobot Roomba 560 Robotic Vacuum
I am working on a u5290-900 hover vacuum ,when operating dust leaks out under dirt cup cover. i put a piece of card board on top of cover so extra presure would be applied to the top of cover. this seams to have stoped the leak , before adding the card board the cover seamed to lift at the back when cover was locked into place. what do you think?
Dear Sir:Will be better idea to replace the cup cover. The pice of card will not function for a long time. Proceed before another extra problem coming.God bless you ... Hoover U5290-900 Upright Vacuum
Hi, have an irobot roomba 530 love it. But it charges ok, when finished the brushes are dirty, but does not appear to be picking up, actually vacuuming into its bin. Asked support in Australia, they recommended unscrewing bottom plate & cleaning of any fluff - which I have done. Still not working properly HELP
Remove the pickup bucket and dump it, then grab the little yellow strip in front of the pickup bucket and clean the hepa filter for free air flow. ... iRobot Roomba 530 Robotic Vacuum
Virtual wall not working - Roomba iRobot 780 Vacuum Cleaning Robot
... Roomba iRobot 780 Vacuum Cleaning Robot
Scooba external charger not working - iRobot 5800 Scooba Vacuum
... iRobot 5800 Scooba Vacuum
My dyson DC17 will not turn on unless the handle is pulled back.(into the vacuuming position) The attachment hose will not work at all (0 suction thru it). I've checked the hose and made sure there is no obstruction. Any ideas?
Not sure if I can help, but I'll try. The DC17 has two motors: the vacuum motor and a separate motor for the brush bar. It is normal that the brush motor works only when the handle is pulled back in the vacuuming position - that's the way it's made. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.
Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem. ... Vacuums
Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!
Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums
I have a kenmore progressive direct drive handi mate jr. upright vacuum. My daughter used it last night to vacuum up some cat litter that had spilled on the floor. I went to use it today and it turned on for a second and then stopped working. I have hit the reset button but it will not turn on. Help this vacuum is only 2 years old Is there anything that I need to reset or do so that the vacuum will work again?
Its probably clogged up with cat litter.might have gotten into the motor.your motor has a motor guard inside if it. when it overheats it will shut down till it cools off.you need to clean all th cat liter out of it.and clean the filters.with a direct ... Kenmore Vacuums
I have a panasonic mc-ul975 vacuum that works great when working properly. the airflow through the canister seems to stops once the aero blast technology is done running which causes the vacuum to not function as it should (does not have as much suction and the hose/tool accessories do not work at all). if air is continually running through the canister everything seems fine. please help!
Hi there. In Panasonic vacuums, there is a thermostat protection on the motor. It will auto ... Panasonic MC-UL975 Upright Vacuum
Hoover U5344-950 My Hoover vacuum is a nightmare! I have had nothing but problems with it since day 1. The powerhead stops working if you try to lower the handle to vacuum. I took it in to be serviced and was told it sat on the shelf for too long in the store and it warped the belt...so it was replaced. Got it home, it worked the first time I tried it, then went right back to no powerhead working and as a bonus it is giving off a nasty smell like it is going to blow up! It now gets really hot to
... Hoover U5344-900 WidePath Vacuum
I have a Craftsman wet dry vac with blower capability (22 L). While I was using it to **** up water, the water came out of the blower hose. Now I can't get it to work as a vacuum. What can I do to fix this problem? Is there a toggle switch somewhere that allows me to choose vacuum or blower? Also, will the vacuum still work without the filter nut attached to the plate? Please let me know at your earliest convenience. Thank you.
... Craftsman Vacuums
I have Hoover WindTunnel Air Upright Vacuum - UH70400 just used couple of times. While vacuuming the carpet carpet fringes were rolled up in to brushroll and brushrol stopped working. It means vacuum is not working effectively now. Brushroll indicator is flickering.
... Hoover Vacuums
My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?
Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums
MC-V7400D Vacuum Vacuum will no longer create a vacuum Changed filter and still does not work. Sounds as if it is working.
Blow in hose and see if it's clogged, possibly a belt is come off. ... Vacuums
My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.
When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum
I have a DC 17. In the middle of vacuuming the vacuum stopped working when it was in the upright position. It only works when the head is down and i am using the bar. I can not use the extension bar, becasue when I put the vacuum upright it shuts off. Where is the problem?
Hi there, it's Jack at Dyson.\012 \012 Like most Dyson vacuums, DC17's main suction motor is protected by a thermostat which shuts the machine down if it starts to overheat. This could be due to a blockage, and the filter may also need a wash ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Vacuum dead I have oreck XLx2 bagged upright - the belt ,plug and cord have been replaced - has been working great - now went to plug it in and it does not work - the light goes on in the on/off switch so power is working but vacuum is dead - any suggestions
If the cord coming from the bottom up to the handle is loose, and is a plug, push it in. If that doesn't help. then could be a problem with the motor. One other thing to check is inside the handle, maybe a wire came loose. ... Oreck XL2200 Bagged Upright Vacuum