Having problems with your Vacuums ?

How do you take the motor brushes out of the Oreck XL3610HH

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you take the motor brushes out of the Oreck XL3610HH

... Vacuums

Sparks coming from under oreck vacuum. looks like its coming from motor brushes.

Probably need to have that serviced at a repair shop. They can tell you whether or not you need a new motor or a fan blade kit. ... Oreck XL Ultra Bagged Upright Vacuum

I have a Electrolux , EL6988 Canister Vacum, howeveer the brushes and motor will not run when turned on. I have take the plates and cleaned around the brushes, but it will not come one. The vacum comes on but the motorized bushes do not activate. Thanks I have lost my owners manual, and have looked for the reset button and can't find or know where it is located. Any suggestions.

I need the molded wire harness inside the plastic wand ( one of the prongs is broke off) What is the part # or where can I buy it? Model EL6988 ... Electrolux UltraLux 2000 Bagged Canister Vacuum

One of the brushes on my oreck bb2000 motor is sparking

... Oreck BB2000 XL Little Hero Canister Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi

Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

I have to replace the motor brushes in my Oreck XL model 2000RH. How do I remove the old brushes?

If it's an AC induction motor there are no brushes. ... Vacuums

I have an older Oreck XL vacuum that sounds like it is running twice as fast as it should. I disassembled the entire vacuum, including disconnecting the motor wires, to clean out the hair, string, and other things. When I put everything back and connected all the wires, everything appears to work, including the light. The only problem is, it sounds extremely loud like the motor is running too fast. The model number is: XL3610HH Ser. No. 3610HHXA039740-6 I do not have as electrical diagram to see

... Oreck XL Ultra Bagged Upright Vacuum

Oreck xl making whinning noise after replacing motor,belt and brush roller..

... Oreck XL Ultra Bagged Upright Vacuum

I got a FREE old but lightly used Oreck XL 8300 xtended life commercial. 120V 60 Hz. After cleaning brush etc. is there anywhere to add oil to the electric motor? Is it necessary? Is this machine worth the time?

Hi,I don't believe that the bearings have a place to oil them. As for the machine being worth the time, I think yes. Orecks are used extensively by hotels, and are noted for their reliability, longevity and weight.Best regards, - ... Oreck Vacuums

Oreck xl3610hh motor wiring - Vacuums

... Vacuums

Brushs arc against spinning motor - Oreck XL2000 Bagged Upright Vacuum

... Oreck XL2000 Bagged Upright Vacuum

I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together

... Vacuums

I have a dyson root cyclone. i dismantled it to replace the belt, it is not the belt which is on the roller brush, it is the belt which is from the motor, it was easy to take out as it was broken, i will get new one tomorrow now im wondering how do i fit it in.

The belt that fits on the motor is the same belt that drives the roller brush, all you need do to gain access is remove the sole plate, normally attached with 3 quarter turn connectors, use large flat screwdriver to turn them ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Oreck XL2200: It turns on, the motor is running, the belt is on properly, but the roller brush is not moving

Quite often this is caused by either a broken or stretched belt, does not seem to be the problem here, or a frozen beater brush, the brush the belt drives.\015\012Remove the beater brush and clean as best you can. Spray a little WD40 between the bru ... Oreck XL2200 Bagged Upright Vacuum

It is making a racket when i turn it on. I took the brush off and cleaned it it is not the belt i don't know how to take the cover off the top front so i can look near the motor can you help please. [email protected] .com Thank you Staci Bishop

These units have two screws that hold the "hood" in place. With the belt/brush roll cover off look on the underside for the heads of these screws. Once these are removed the top should come off. ... Hoover U5096-930 Bagged Upright Vacuum

How to take brushes out of motor on a lindhaus sweeper

... Lindhaus CH pro Hepa Bagged Upright Vacuum

Is it a difficult task to take out the whole brush motor and clean?

Yes, the agility series is not the easiest to work on. I would take it to your nearest dealer for service. cover screws can be seized and nozzle could break. ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

How do u get muddy grease out of your carpet - Oreck DutchTech DTX1300C with Motorized Carpet Brush Bagged Canister Vacuum

... Oreck DutchTech DTX1300C with Motorized Carpet Brush Bagged Canister Vacuum

Motor doesn't run I believe it the brush on the motor. two motor brushes one is completly gone about 1/8 inch left could this be the problem.the other motor brush still has 1/2 inch left. and current to motor tested good.

Sounds like your belt slipped off. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Shopvac 90L400 quit working (4 years old). Thought the switch was bad but not the problem. I read that there is a fuse link in the motor that frequently burns up. I tried to take motor apart but not sure of the process. I was able to get to the motor but cannot pull it out of the armature. It appears I have to take the aluminum blower unit off the shaft (it appears to be pressed on with a retaining washer). Do I have to take it off to pull the shaft and motor assembly out? Is that where the fuse

By pass the switch and take power right to the motor leads.. that should tell you if the motor is ok.. have not seen fuse link on a vac motor.. graingers has new motors, but not inexpensive ... Vacuums

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you

Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

Not exactly a blow gun. Convertible blower/vac - Sears Craftsman. Wire broke off ONE brush in the motor. Paid about $90 for the vac - Sears lists the WHOLE motor as one part - $88. Have requested brushes (they are provided with a lot of my 'cheap' Harbor Freight tools) but no go. Just get the canned reply - buy the whole motor. Actually got it working again... CAREFULLY drilled and tapped a 4-40 screw into the brush and soldered the lead to that... Always a way, isn't there?

... Vacuums

How to replace the motor brushes? When should the motor brushes be replaced? Where can I purchase motor brushes for Model 1500 Easy-flow?

... Easy Flo EF1500 Vacuum

Where can I order the following parts for my 1952 KENMORE SEWING MACHINE MODEL #117583, SERIAL #48054: : #5107 carbon motor brush (2) #5110 motor brush spring (2) #5111 motor brush spring cap (2) String for starter control lever Pulleys, screw and nut washer to attach string control Best sewing machine ever and still working like new, and I want to keep it that way. Thanks.

... Vacuums

Brush motor does not turn. Vacuum motor works. How to replace brush motor?

... Eureka 431A Optima Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0729 seconds