Having problems with your Vacuums ?

Control board location - Vacuums

Answers :

Control board location in what make and model vacuum?
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Control board location - Vacuums

Control board location in what make and model vacuum? ... Vacuums

I am looking for a contol board for a miele s143 stick vacuum. The vacuum wont start but when I supply power directly to the motor it spins. I think the switches are OK so I have concluded it is the control board Thanks Don Kenney

You should check the cord and switch's for continuity, the boards are usually pretty reliable, you could check the board for any bad solder joints, at least that would be obvious. ... Vacuums

My Kenmore canaster vacuum Mod# 116.25513506 runs continously when plugged in regardless of the on/off hand controlled switch.. Disconnecting the switch located on the hose assembly has no affect of the continous vacuum operation. What component in the electric motor circuit is at fault and what would be the cost of repair?

... Kenmore Vacuums

My danby kegerator model DKC645BLS controller circuit board corroded and no power to the compressor,I already have an external temperature controller,can I just bypass the controller and circuit board

... Vacuums

I have an Eureka Express canister vacuum - I believe it's model 8284 - that just stopped working. Plug it in, turn it on, and absolutely nothing happens. I took it to the local sew and vac place and they say it's a circuit board that is no longer available. I've looked at all the parts lists and diagrams for that vacuum and I would swear there isn't a circuit board there. (I wouldn't have even thought that in 1989 they would have used circuits.) In any case, I absolutely love this machine a

Given the age of the machine weighed against you fondness for it, unless you can find a fault with either the switch or the cord, there is little else that can be done. With time the electrical lead can break down and one o ... Electrolux Vacuums

Miele Champagne Vacuum Cleaner Model S548 I was using the vacuum as normal, moved locations so I plugged into another outlet & suddenly there was no power to the vacuum! I tried it in several other outlets, tried the reset button... & still no power to the vacuum. Any ideas what could be causing this? Any info would be greatly appreciated. Thank you!

Greetings from ,\015\012 \015\012This definitely sound like a cord reel issue to me. This is really the only problem that I ever see on a Miele vacuum cleaner. 9 times out of 10 the cord reel needs to be changed. If you purcha ... Miele Blue Moon Bagged Canister Vacuum

I have one central vacuum location that does not receive power. All other locations work. I do get suction but just no power. What should I do first to test power to location.

Remove the face plate from the wall and test the low voltage wiring behind. Before undoing the screws where the wiring connects, reach inside the inlet and feel the two brass pin connections. There should be spring tension behind each. Underneath the ... Hoover S5604 Central Vacuuming System Power Unit Vacuum

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin

... Vacuums

I have one central vacuum location that does not receive power. All other locations work. I do get suction but just no power. What should I do first to test power to location.

You need to use a circiut tester (electrician test probe) on the two terminals the hose plugs in to to see if power is present to connect to. The receptacle likely has damage to the power connection from arcing from the hose previously not fully plu ... Hoover Powermax U5242-930 Vacuum

Vacuum cleaner We have a panasonic MC-E47electronic which seems dead. It has a speed control which we nearly always had on full anyway. Have tested continuity through plug, flex and on/off switch and all OK. from then is open circuit through speed control which consist of slide rheostat and mystery small green box (2cm x 2cm x 1cm approx). Across motor there is negligable resistance. Machine is quite old and not worth paying out loads on poarts if it is safe to bypass speed control and connect

Yes it is safe, but i would make a switch? ... Vacuums

I bought a house that has a 1970s GE microwave oven that's built-in above a traditional oven. (Unfortunately, I can't locate a model number for the microwave.) I'd appreciate having information about the "food temp control," which is on the front of the oven. There is a wire probe that goes from the inside of the microwave to the food. I assume that relates to the "food temp control." I'd appreciate having any information about how to use the "food temp control." Also, I 'd like to know wh

I serious doubt that probe would work any longer for they go out in ten tears or less ... Vacuums

I have a Series G Kirby Model G7D. The other day when I was vacuuming all of a sudden the TechDrive (Power Drive Assist N/D) pedal fell off. I see the hole that it goes into but when I put it in it's loose and falls out and doesn't control the power drive anymore. When I shook the vacuum I heard something rattling around inside the vacuum head. So I unscrewed the bottom and looked inside and found a small metal part labeled K3 on one side and T on the other side. It looks like it would fit

Hi, I have a Kirby G4 and i'v replaced the carbon brushes myself using a step by step guide however since its been back together it worked for about five minutes it then started sparking from the inside!!(a lot!!) I'v obviously touched something i sh ... Kirby Ultimate G Bagged Upright Vacuum

FAN PROBLEM??? good morning! my vacuum smells like burnt rubber (fan perhaps) but I can't find how to get into main part of the vacuum. it's just very rounded with no latches or screws to get inside where the motor, belts and fans would be located. can you help me? thank you

There isn't any belts, and the fan wouldn't be rubber, so not sure what you are smelling. Maybe this picture will help you.\015\012\015\012 ... Bissell 6700 Butler Revolution Bagged Canister Vacuum

My Eureka central vacuum of almost 10 years, has a reoccurring problem, of a defective relay on the pc board. The problems is usuallly the motor will not turn off. The pc board has been replace 8 times, of which 3 times were with in the last 4 months.

Are you taking the machine in to someone? or is this a self diagnosis?? \012\012What I mean with those questions is, sometimes it isn't the PC board that is causing the problem. Sometimes it is something else. Even the people that you are ... Eureka CV1804B Bagless Central System Vacuum

Electrolux EL7024 Oxygen Vacuum. On Off button works. When "carpet" floor selection is made, vacuum shuts off. Additionally, sucction control is inoperative.

... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

My Dyson Blueprint bagless rollerball vacuum brush refuses to turn every so often. Everything is connected properly, nothing is clogged in the brush, the vacuum power is turned on and then the brush bar control is released, but the brush still does not turn.

... Dyson Vacuums

4870 Boss Smartvac. The vacuum tipped over and now the brush control lever will not stay in the carpet position. I can't get the brush to turn unless I push down and hold the lever. As soon as I let up on the lever the brush stops turning. Any ideas. The vacuum is only a month old.

The Boss has a slide lever on the top of the power nozzle with two position choices. One position is "Carpet" and the other is "hard/bare Floor". The power nozzle brush roll is activated when the lever is in the Carpet position, and it is t ... Eureka Smartvac 4870 Bagged Upright Vacuum

Circuit board i have searched far and wide looking for a circuit board for my fantom cyclone xt, so far i can't find one .. is their anyone who can can locate or sell me one of these hard to find items. i am at the end of my rope ! any help is appreciated, thank you for your time TOO SLIM

Http://www.vacmall.com/supplies.asp?Brand=Fantom&Model=Cyclone+XT ... Fantom Vacums Cyclone XT Upright Vacuum

The repair shop told me my Oxygen3 needs to have a sumo(?) board replaced...again. I am not willing to pay for another repair and am wondering whether an new hose and adjustable extension tube would solve the recurring problem. Is the sumo board located in those parts or is it a malfunction that transfers to somewhere in the canister?

The Sumo Board, is housed inside the canister section, part # and discription below\015\012E-1180136-56 SUMO BOARD\015\012So replacing the hose and or wand will not fix the problem. Suggest you stay away from "big box", retail, discount s ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u

Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums

Kenmore Vacuum 116.35622: Need to know how to attach the board to the vacuum that is supply the power to the motor. (need the electrical diagram) email: [email protected]

... Vacuums

I need a relay board for a Nutone CV 450 12.6 amp dual motor vacumn unit. Where can I locate one? Part #??? Unit will run by itself, then shut off. Unit wll not run at all. It has a mind of its own. Crossed a couple of wires on one of the relays and the unit runs smooth as silk. I assume its the relay, but can't locate part number.

Why not just replace the relay? Part number 1094117... ... Broan-NuTone CV450 Central Bagged Central System Vacuum

Where is the hose located on dyson animal? Is it in the vacuum itself? Can you print a copy of the booklet showing how to operate the vacuum?

The hose is located in the tube that runs down the back of the machine below the handle. Just pull the handle upwards and the hose will come out with it. You can find owners manuals on the Dyson website, also phone numbers for help lines (may or may ... Dyson DC07 Bagless Upright Cyclonic Vacuum

GM 150 freestyle - need to separate 2 red halves to locate a problem. I am a retired electrician but cannot locate the means of opening the speed control end so that the whole top section may be removed. I would appreciate your help. Thank you. Ken.

... Nilfisk Vacuums

Simplicity Jack turns off repeatedly during use. Vacuum doesn't feel hot. I have opened up the vacuum and have checked wiring etc.. Is there a faulty censor on the circuit board. How do I check or replace needed part?

... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1080 seconds