Having problems with your Vacuums ?

Eureka Central Vac-Sweeper -Model B1501

\015 There is something clogged in the sweeper (not the hose) of our Eureka (The Boss) vacumn.\302\240 How do I get in there to clean it out?\015\012Thanks\015

Answers :

First undo the hose from the base and then take the cover off from under the vacuum, remove the brush roller and belt, then note where the suction hole is and shine a light through the hole and look in the other side, if there isn't any light, then place an object through the hose side of the hole, if there is light, then follow the hose to the holding container, remove the hose from that, then turn it on if no suction from this point, then remove the container and turn it on, you should have some suction coming from the vacuum motor. If so, clean the filter(or replace) dump contents, and reassymble.
Its not easy to get into the sweeper head. I would push a air hose in there and blow the head clean. You will need to find a compressor or your friendly local workshop manager could help you.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Eureka Central Vac-Sweeper -Model B1501


First undo the hose from the base and then take the cover off from under the vacuum, remove the brush roller and belt, then note where the suction hole is and shine a light through the hole and look in the other side, if there isn't any light, then p ... Vacuums

We have an Eureka The Boss Central Vac Model ACV2001B. When you plug in the vac the motor starts momentarily and then stops. What could be the problem? Thank you.


Most likely there is a short in the low voltage wiring in the hose. ... Vacuums

I have a model 1561 electrolux central vac..can i use a hose and accessories from a model 15448 model electrolux central vac to compliment my central vac unit


If the hose fits into the inlets, then there should be no problem. ... Electrolux Centralux Vacuum

I have a Eureka Mega Boss Central Vac Model # CV1801P. The suction works when the handle button is pushed left (floor mode) but no suction happens when the button is pushed right. When the floor attachment is hooked up and the button is pushed right, the brush rotates, but there is no suction.


... Eureka Vacuums

We just moved in - the house is about 9 years old. I have a Eureka Mega Boss central vac - looks like model # is CV20220. 12.4 amps, 120 volts. Can't figure out what type of bags I need. Can you help?


Well, for this unit you will need any of the following bags, Eureka genuine Part# 90610Eureka replacement (Central vac bag) another genuine bag style called CV-1, and/or CV-2Kenmore Central vac bagsMost of th ... Vacuums

Eureka central vac 's power stopped won't start again.


I took to dealer I bought from . He examined it. The motor is gone needs new one. Thanks, Ann ... Eureka 1810 Central System Vacuum

I need an owners manual for a Eureka Quick Up stick vac, Model 96


... Eureka QuickUp Upright Cordless Stick Vacuum Vacuum

I have a central vac beam model BM1372 the rug


... Vacuums

I have a Hoover Central Vac model S5673 and it stops periodically


... Vacuums

I have a Kenmore central vacuum cleaner model number c107 34601. We have emptied the bucket and shaken the filter out to clean it. There is a filter that is filthy so we shook it out into a bag but the cleaner still seems to not have great suction. I notice there is a similar cap to the outlets I plug the central vac hose into on the unit itself that doesn't power the nozzle when used. 1 - what is this for? 2 - Should I somehow remove the entire filter and if so - can you tell me step by step ho


... Electrolux Vacuums

Kenmore Central Vac model 34730, no power at Unit


... Easy Flo EF1400 Central System Vacuum

Getting a Eureka central vac cloth bag back in after cleaning


I found that if you start by making sure that the tab that you pull to remove the filter is in a spot where you can reach it next time you need to remove it. Next, put the filter in over the inlet spoutand push it up to the white "stops" then gently ... Vacuums

How to change belt on Dirt Devil Model 2003 can vac sweeper


I found out that the Royal Mfg. Co. used the same schematic from this model to make newer models which had a belt, however, this older model that I have does not have a belt drive. ... Vacuums

Need a manual for a beaumark central vac model # 97456


... Vacuums

Kenmore Manual I am looking for a manual for a Kenmore Central Vac ....model # 34630


Sears/Kenmore central vacuum systems are no longer being made ergo no manuals available,especially on line on line. If contacting Sears parts directly, maybe one may be purchased ?\015\012\015\012 ... Kenmore Vacuums

Need a belt # SFP27605 for an Optima bar for a central vac model # HM920 and also the light bulb for it


... Vacuums

How do i change the belt on my eureka enviro vac model number 3041 BZ


... Eureka 3041BZ Upright Vacuum

Wiring diagram for Model #11635922500 - KENMORE Upright vac I took the cover off of the vacuum to repair the power cord and must have pulled a wire out of its wire nut by the sweeper bar. If I had a diagram it would be no problem to replace. The bad has four short gray wires coming out of it. It is one of the gray wires that has come loose.


... Kenmore Vacuums

On my Air Vac model AV425A Central Vacuum System, I discovered the circuit breaker opened. When I close it, the vacuum motor goes on. It doesn't matter which position the on/off switch is on, it runs until I open the circuit breaker again.


... M&S Systems ZX7000 Bagged Central System Vacuum

How to clean the EUREKA ENVIRO VAC MODEL 3041 PARTs? specially the filter? ,.


... Eureka 3041BZ Upright Vacuum

Eureka Boss central vac wont turn on?


... Vacuums

My eureka central vac power brush turns off when pushing forward than back on when pushing back. Ever seen this before?


Yes I repair them all the time. What that means is that the connection of the hose handle to the power brush upper wand is loose. This can happen over time with use. The connection just loosens up. Do you have the exact model of the power brush? ... Eureka 1810 Central System Vacuum

Have a Eureka Power Plus 12.0 Amps Model 4702 Type A 120 volts and 60 HZ that there is something wrong that it isn't picking up right and you can actually feel the air coming out of it near where the bagless canister attaches. My thoughts are that a seal is missing around where the hole lines up when the cannister is locked in. This Vac was my Mom's and she passed away and I think a part went missing maybe when it was taken apart to clean the filter and empty the canister. Need to figure out if


... Vacuums

I have a Eureka Central Vac CV1601b. The motor does not stop unless the Unit is unplug from the electrical outlet. Any Idea?.I removed the control unit to check if there was disconnected wires or burnt wires. Everything look normal. The circuit board does not show area that overheated. There seem to be 2 relays. Likely one of the two went bad. What do you think.


If the unit is relay controlled, there is always the possibility that when the unit was turned on, the relay contacts welded themselves shut making the power button ineffective. \015\012\015\012If you're familiar with relay pinouts, with ... Vacuums

Continuous running My Eureka Central Vac will not turn off. I have to unplug it.


Central vacs have relays in them, some stand alone, others mount on a circuit board. A stuck relay causes this type of problem. At the unit disconnect the low voltage wires, plug in your unit, does it still come on, if it does then you have a bad ... Eureka 1810 Central System Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0677 seconds