Having problems with your Vacuums ?

Ryobi RPBV2500 My blower only seems to ant to run when the choke lever is at the first position. It did run with the choke completely off but seemed to suffer from what I thought was fuel starvation when it ran for awhile. When I took the fuel cap off it would start up again, making me think it had a fuel lock. I had a garden centre with engineers look at it.They said that they had checked the carb and could find no blockages. Can you please help?

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Ryobi RPBV2500 My blower only seems to ant to run when the choke lever is at the first position. It did run with the choke completely off but seemed to suffer from what I thought was fuel starvation when it ran for awhile. When I took the fuel cap off it would start up again, making me think it had a fuel lock. I had a garden centre with engineers look at it.They said that they had checked the carb and could find no blockages. Can you please help?

... Vacuums

Don't want an expert. I wan someone with authority that can make an intelligent decision regarding the way you sell replacement filters. It looks as though the patients are running the ward at HQ. This freak insane! Maniacal and just plain stupid! Tell me something Mr Expert, my closest choice was "vacuum expert" How is this expert going to know and fix the asinine way b&d devised a plan so that the consumer would enjoy wasting a better part of their day. Who, please tell me, who with a drop of

Ouch! So go into Lowes get a 10 pack of electrostatic register vent filters back in the furnace filter section. Take your old filter off and if it's a paper corrugated looking cone just wash it really good and dry it out...if it's disintegrating then ... Vacuums

Dehumidifier fan and compressor run fine (hot and cold coils). But it ices up almost immediately (room temp 68 degrees f). Defrost feature seems innoperative. Anti-frost sensor? Defrost heater? Controls? It also sometimes gives wildly incorrect room temp and % relative humidity readings (when compared to a quality thermometer/hygrometer) making the control panel look suspicious.

Hi,Here is a tip that I wrote that will help you understand why and what you can do with a dehumidifier that ices up. ... Vacuums

Recently my central vac system started making a louder than usual and laboured sound when in uise, enough so that I took note and inspected the canister and motor while running. The motor was trowing off blue sparks and looked like it could 'POP' at any moment. I will not risk using it until I know what the problem is and how to repair it. My assumption is the motor needs to be replaced. The system came with the resale house I bought 3 yrs ago but I do not know the age of the system itself.

... Vacuums

Engine cuts out after running for a short period of time

... Clymer Evinrude/Johnson 2-70 HP Two-Stroke Outboards Includes Jet Dri

I am looking for a specific part for a Nostalgia Electrics RIC-100 portable ice maker and I am finding it very hard to find what I am looking for if I could get some help that would be great. The part I am looking for is the the tray that the ice maker puts the water into and holds to freeze the water to make the ice before it is dumped into the holding tray for the rest of the ice

... Vacuums

We have the GE sensor microwave WES1358DN1WW. It was made in 5/2009 & bought in July of 2010 brand new. it worked perfect til last week. i put something in it & it started to make a loud humming/vibrating noise. i assumed it was just something ontop of the microwaved & ignored it. 1 min later my food was still ice cold. we tried unplugging & plugging back in & made sure that it was clear of anything but it still makes noise & doesn't heat. GE charges $79 to look at it, & since the microwa

... Vacuums

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.

... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum


The vac is over heating. First, you should try a new filter. Also, keep in mind that after cleaning the filter, make sure that it fully dries. Using a wet or damp filter clogs it quickly. Second, turn the vac upside down and make sure that the roller ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Nutone Broan CV556 runs continuously and will not shut off until I unplug it.. I disconnected the low voltage wires and it still runs when I plug it in. Inside the top of the vacuum are 3 electrical devices - one looks like a transformer wire -- one is a rectangular electronic black box. The third is an on off rocker switch. Which piece it likely to be shorted out? It is about 8 years old.

... Broan-NuTone CV556 Cyclonic Bagless Central System Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o

Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?

Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

I have a vax power jet carpet cleaner it is afew years old my problem is when cleaning carpets it makes black streaks all over the carpetwhenthe capet is dry you can see these streaks and it makes the carpet look even dirtier than before i went to wash the carpet . can you give me any suggestions as what is wrong thanks

... Jet Vacuums

Does the hoover runabout u427-930 have a filter? I replaced the belt and next to the light bulb was a square gray mat that looked like a filter covering a screen full of holes that looked like the motor was behind. I think it was a mat of cat hair so I took it off and threw it away; I just want to make sure that it wasn't a filter that I need to replace.

From doing a search on the internet and hoovers website it looks as if this unit does not have a filter. Such as a hepa that needs to be replaced or that is washable. So i think you are safe and dont need to worry about it. ... Hoover Elite U5061-900 Bagged Upright Vacuum

I have what I thought to be a Kirby Classic Omega that is in excellent running condition and looks great. I love it and have been using it for years, but it is recently going through an identity crises! I looked on the identification plate under the motor while cleaning it and discovered that the ID sticker says it's a Kirby Classic III. How can this be when every part of my dear kirby is Omega brown? There is not a hint of Red or Rosewood! Is there another way to determine the actual model b

The Kirby Omega was made from 1973 to 1976.The classic III 1976 to 1979When in for repair the case (motor cover) from a Classic could be put on the Omega. This happens in repair shops if the teck. has two apart at the same time and was no ... Vacuums

When I vacuum w/ the brush control in the on position it make a really loud noise, almost like a grinding sound. I have looked at it and nothing seems to be wrong, but I notice that the pin that engages the belt seems to vibrate a bit, possibly creating the noise. It started when I accidentally got part of a plastic grocery bag caught in the brush. Could it have stretched a belt? Nothing is caught any other place and it only makes the noise when the brush in in the on position.

Yes, the belt could have been stretched and is now vibrating and hitting other parts and creating a noise if much of the bag got caught under the belt. If you have another belt for this vacuum, please put it on and see if the noise stops. If it does ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

The engine makes a funny noise and the brushes make sparks.

HiThe bearings are not replaceable. If the bearings have gone you need to replace the complete motor ... Electrolux UltraLux 2000 Bagged Canister Vacuum

It makes a loud noise when turned on. it doesn't make the noise when you use the hose. It looks like the roller on bottom is cracked where the belt wraps around it.

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Eureka 2961AVZ Will not start ...I get a momentary flicker of power about every 3d or 4th time that I flick on the power sw. Outlet is fine / Plug looks good / chord looks good / I see no obstructions ........Would appreciate any helpful thoughts ....Trying to get Mom's Eureka 2961avz back up and running. Thanks

CAREFUL! This is how my problems started. The cheap switches (and wiring) Eureka is using in some models, especially my model) should provoke a lawsuit imo.Here's my story, just in case it might help. Mine started with a problem very similar ... Eureka 2961AVZ Bagless Upright Vacuum

It's making a very loud noise when running. I have a Bissell Quicksteamer series 2080. When I was using it yesterday it was making a light squealing noise then it turned into a loud racket. I shut it off and and cleaned the brush (lots of dog hair on it) But the racket continued.

... Bissell 1770 Quicksteamer II Upright Vacuum

I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums

I have a irobot roomba 560, that doesnt go back to dock for charging, he just runs until the battery runs out? What can I do to make it go back to the dock ?

... iRobot Roomba 560 Robotic Vacuum

Clogged vacuum Rather stupidly, my boyfriend 1) were vacuuming without a bag and 2) vacuumed up a big piece of cotton from a sofa cushion. And now it's making a horrible noise and I see it vibrating where the tube connects to the machine. When you look inside there's a white thing sticking out but it looks like it's part of the vacuum. If it's a clog, how do you fix it? I tried unscrewing the tray the bag sits in but it won't budge.

You can start by taking off the bottom plate or top cover, which ever comes off, that is where the inlet starts going in and hopefully the clog is there. Could be in the hose also. But without the complete model number I can't look it up to see a p ... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

I cleaned out my dyson ball as it smelt when i hoovered, cleaned filters, washed out canister and took the screws out of the front bar so i could clean near the brushes.. now its making a high pitched noise and when i switch it off it makes a noise like an engine shutting down! Have i disturbed the motor?

Hi its Darran at Dyson. The screws on the base of the cleaner head should not have to be removed to access the brush bar so it is possible that the brush bar has come out of alignment, hence the noise the machnie is making. Pl ... Dyson Ball DC24 Bagless Upright Vacuum

The engine in my vacuum is making a loud rattling

If its over a year old junk it if not it would be under warranty ... Bissell 3102-0 EasyVac Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0499 seconds