Having problems with your Vacuums ?

I have a clog with my Oreck Halo how do I remove the clog


Answers :

Take hoses off and push a certain wire through the pipes, mainly behind the brushbar,, click the link below for manual
http://demandware.edgesuite.net/aajc_prd/on/demandware.static/Sites-oreck-Site/Sites-oreck-Library/default/v1375113337274/images/userguides/Vacuum-Halo100-Halo-userguide.pdf
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a clog with my Oreck Halo how do I remove the clog


Take hoses off and push a certain wire through the pipes, mainly behind the brushbar,, click the link below for manual ... Vacuums

How do I remove bottom panel on oreck halo?


... Oreck HALO100 Bagged Upright Vacuum

I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth


When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums

The removable filter at the front is cleaned regularly, and is not clogged. However, the machine appears to be suffering from being clogged by dust, as it has started to make a high pitched noise, and I fear it may burn out. I can see some dust inside the front panel but cannot see how to remove the front to clean it out. (NB. I have located two screws - one on either side - but cannot see how to proceed further.) Please help! Thank you.


\015\012\015\012Hi,Here\015\012is a tip that I wrote about my Bissel but I bet you have the same\015\012problem and the hose is clogged...Bissell Bagless Upright\015\012 ... Vacuums

I have a EuroPro Infinity NV29 and I have a clog in the base. I have removed the screws and the plastic piece where it says access port to remove clogs but don't know how to get the hose lose to empty it.


... Vacuums

Is it possible to remove the brush bar from the housing of a mieleTurbobrush STB 205? The brush bar is not spinning due to been dirty and clogged and needs to be removed for cleaning. Is it possible to remove the brush bar????


... Miele 06271980 STB 205-3 Turbobrush

Clogged hose... I have a clog in my hose, probably a sock, I have pushed it through to the hard plastic handle end of the hose, help! can the plastic handle wand be disconnected from the hose to remove the clog??? Thank you


Hi!\015\012 \015\012Low suction, poor pickup, or no suction may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor or a reduction in the spinning action in the Dirt Con ... Bissell 6594 PowerForce Bagless Upright Vacuum

Oreck XL How to remove rear wheel. Removed all viewable hair, thread, etc., but one wheel is still hard to turn. I think there's hair stuck inside the wheel core. Can I remove the wheel & take it off the metal post?


You can take a medium size flathead screwdriver and slide it in beside the wheel and under the pin. Then pry carefully on one side and then the other it will start to come out but work both sides alternately so you won't put too much pressure on the ... Oreck XL2000 Bagged Upright Vacuum

How to I remove the hose from the base of the bissell spot clean pro to remove a clog.


Dont no if this one is the same ,but it may help you, click the link belowhttp://www.youtube.com/watch?feature=player_embedded&v=1sSVIu6arbY#! ... Bissell Spot Clean Pro Portable Deep Cleaner Professional Spot Cleaner

How do you remove the access port to remove clogs on the Shark vac


... Vacuums

I have a clog in the hose and can't get it out. Is it safe to pour water through the hose to remove the clog?


... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

I have the Miele S7280...the one without the clog hatch on the back. I took the bag cover off, then continued the remove the screws and cover underneath it to detatch the top from the bottom. Found the clog and cleaned it out. Heres the problem...now the power nozzle light comes on and the vacuum "on" is lite up red, but it will not come on. Checked the filters and the bag. It certaintly seems like the top and bottom are meeting up to latch into each other, but I have no power. Help!!


... Miele S7210 Bagged Upright Vacuum

How to remove the hose from the canister to remove a clog


... Dyson DC22 Motorhead Canister Vacuum Bagless Cyclonic Vacuum

How to remove oreck 2605 hh motor - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Oreck XL9100 Our vac motor was removed to remove a hairpin in the motor.? The tape fell off the wires. Do you have a wiring diagragm?


See diagrams ... Oreck XL Ultra Bagged Upright Vacuum

How do you clear a clog out of the wand? There has to be a way to remove the clog without damaging the hose.


I would push a length of stiff wire through to ease out the blockage.pete ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Can't remove bottom plate to change broken belt on oreck xl instashield vacuum ...i think i removed required screws


... Oreck Vacuums

It's an upright, model X4. The bag full or clogged light is lit. I've takent the thing apart and cleaned it out, and removed some clogs. But the light won't go out and when I run it, it stops after a minute or so. Also, the pedal for lowering the machine to use it has come off and I can't figure out how to reattach it.


There is a short hose inside the housing where the roller is. Did you unclogg this as well? ... Sebo Vacuums

Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?


Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum

I have a Hoover U5111-900 that, every time I attempt to use it, shoots everything it should be sucking up, back out toward my feet. I have replaced the bag, pulled out lots of animal hair and such from the area behind the bag, and taken off all parts able to be removed without a screwdriver and pulled out all chunks of hair, dirt, etc. It still keeps shooting everything it should **** up out the back. Is there something I can remove to get the clog out if that's the problem? I'm scared I wil


Hello,\015\012\015\012Although I could not locate info on a U5111900, the link below shows a similiar upright and things to check for clogs. See page 12 and refer to the pages noted.\015\012\015\012 ... Vacuums

ORECK VACCUM older oreck xl, new belt , new bag, checked for clogs, does not pick up as it used to, and, much harder to push, seems to grab or drag, why????


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=747767\015\012Generic problem for all Vacuums\015\012ORECK VACCUM\015\012Posted by FISHERMAN928 on Jul ... Vacuums

Oreck XL My Oreck just turned off in the middle of vacuuming and I smelled a burning smell. I am thinking that if I can take it apart and remove whatever turned it off, it will run again.


Your roller brush is probably bound with hair and is not able to move ... Oreck XL2600 Vacuum

I have removed a clog from the hose and cleaned the air filter. But I have no suction. If i remove the filter the is plenty of suction.


Get a new filter ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.


... Sanyo Vacuums

There is no suction, hoses do not appear to be clogged, is there a way to remove the piece underneath to see if there is anything clogged there


The top cover to the housing comes off in order to get to the roller brush area to check for clogs. There are two screws in the back of this cover to take out and then the cover will come off. ... Euro-Pro NV31 Infinity Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0289 seconds