Having problems with your Vacuums ?

How do i blow my nose properly? - Vacuums

Answers :

On your shirt
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do i blow my nose properly? - Vacuums

On your shirt ... Vacuums

** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I

You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

Suction problems My Hoover elite vacuum (which is less than a year old) is not sucking up properly. Also, when I detach the tube that goes to the vacuum cleaner so I can add my attachments, it blows OUT dirt through that opening. HELP!

Sounds like a clog right near the front ... Hoover Elite U5061-900 Bagged Upright Vacuum

Local vacuum repair shop replaced motor in Oreck XL 2600HH and now the lights blow out immediately upon powering up the machine. I believe the wires for the lights were mis-wired to the terminal blades on the motor housing. is there a wiring diagram available to properly connect the wires to the motor housing?

Hello. if this repair just occurred return this vacuum to that repair shop as they owe you a valid repair. I agree that they caused the lights blowing out problem. They must repair this for no charge. If you work on it yourself they will blame yo ... Oreck XL2600 Vacuum

Hello, we have a Miele cat and dog turbo 5000 vacuum cleaner which we bought in December. It has just started blowing air out of the grid on the top of the cleaner instead of sucking from the tube. The whole top section which is opened to change the bags doesn't seem to want to clip down properly either. Do you have any ideas> I'm gutted as it was so good until this happened. Thanks Michelle.

The lid not closing properly is almost certainly the cause of your problem. Without that lid sealed tight to the body you will get no suction through the hose. So, the question is: why isn't the lid clipping down properly? Did you just change the bag ... Vacuums

I have a Hoover Steam Vacuum, All Terrain, and the bristle brushes are not rotating. They appear to be seated properly and, the entire vacuum is clean and free of lint, hair etc., so everything is working properly except the brushes do not rotate. Any help would be greatly appreciated. Thank you.

I checked the owner's manual and the parts breakdown for your model F5807. Both showed that your model has a stationary brush strip and not rotating brushes. Is F5807 the correct model number? ... Hoover F5807 SteamVac Wet/Dry Vacuum

My shop vac blows and doesn't ****! I put the hose on either hole and it blows dirt all in my house. I'm trying to vacuum. I can't find a switch to change it from blowing to sucking and if I put the hose in either hole it just blows.

... Eureka 2812 Wet/Dry Vacuum

When I try to use my vacuum the hepa filter blows off the front of the vacuum

Sounds like the latch is broken. get a new filter door at a vac shop ... Eureka 2961AVZ Bagless Upright Vacuum

I have a kenmore vacuum and the head of the vacuum is not turning as it should..what do i do? Everything else seems to be working...I tried to reset it but nothing happened. One more thing what is the head of the vacuum properly called?

Replace the belt on the vaccum. ... Vacuums

The vacuum does not **** in dirt. It is blowing air instead. Yet when I disconnect the vacuum from the cannister, the suction seems very strong. I took it to a vacuum repairman, and he said that Kenmore sucks and I might as well get rid of it. (He wanted to sell me another one) It is 10 years old, but if I can fix it I would like to try.

... Kenmore 22613 Bagged Canister Vacuum

When we turn on the vacuum, the canister falls open. The clips holding the canister in place do not seem to hold the canister tightly which I'm sure that it did in the past. The clips do not look bent, but every time we turn on the vacuum the intense pressure blows the canister open only remaining attached the the rest of the vacuum by one clip

Check filter and make sure it is kept clean at regular intervals. Possibly worn out clip retainers on cannister side due to excessive pressure build up. Do not force closure unless pressure is back to normal. May crack cannister or damage unit beyond ... Hayden Industries SuperVac 6000 Central System Vacuum

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!

Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

Hoover Upright Vacuum model U5470-900 - The On/Off switch on the handle does not properly engage the power switch deeper in the handle assembly. It appears to ride over the lower switch and doesn't engage it to operate it. If I play with it, I can get it to maybe turn on the vacuum, but, then the upper handle switch won't turn it off. Our current workaround is to use the power cord for on/off operation.

... Hoover Vacuums

Have model 3576-6 Bissell Cleanview II and drive belt keeps slipping off peg that is sticking out from motor pulley causing vacuum to stop working properly and brush to stop moving properly

... Vacuums

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...

The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My vacuum blows air instead of sucking air. I have a dirt devil swivel guide. I got something stuck in the brush spinner, got it out...but now the vacuum doesnt suck stuff up anymore.

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=571660\015\012Generic problem for all Vacuums\015\012My vacuum blows air instead\015\012Posted by katweaver3 on ... Vacuums

Will not **** up, but blows out air - Eureka Capture Upright Vacuum Vacuum

It may not have any blockage due to an object(s) stuck in hoses and/or vacuum. Even though the brush might be spinning, you probably need to replace the belt ... Eureka Capture Upright Vacuum Vacuum

It is blowing dust out of the motor - Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

If this is a bagless machine, then the problem is that the really fine dust that you are picking up from your floor is so small that it is going through the filter and dust cup and building up in your vacuum motor. When enough build up collects, the ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Changed the motor carbon brushes on my Beam central vacuum cleaner equiped with an IntelliWatch system. This system includes the Alutron DB100 module. This Alutron module needs to be reset so that the vacuum cleaner can operate properly. I believe that this module keeps log of running time and disables operation after a predetermined time. Can you help me with providing a reset procedure that will reset this module. Thanks

... Sunbeam Vacuums

How do I get my vacuum cleaner to blow air instead of **** air? I want to use it to blow up an air bed - Nilfisk King 240

... Nilfisk Vacuums

Hoover EmPower 4600 keeps blowing circuit breaker. The number of outlets in the house that will allow me to run the vacuum is dropping quickly. It is a 4 year old house and all the circuit breakers are 20 amps. The vacuum only has a 12 amp motor. I am at a loss to solve this problem.

Take it to a friends house and plug it in if it does the same thing then the problem is in the vacuum cleaner.check your cord and see if there are anny cuts in it.you can open the breaker box then plug in the vacuum and watch the breaker box.you migh ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I purchased a Eureka Vacuum The Boss SmartVac one year ago, I misplaced my manual. The problem is when I try to vacuum dust blows every where as dust storm. How do I resolve this problem?

It sounds like your filters are dirty and if it is a bag system the bag is full or not seated properly ... Vacuums

Hoover U5344-950 My Hoover vacuum is a nightmare! I have had nothing but problems with it since day 1. The powerhead stops working if you try to lower the handle to vacuum. I took it in to be serviced and was told it sat on the shelf for too long in the store and it warped the belt...so it was replaced. Got it home, it worked the first time I tried it, then went right back to no powerhead working and as a bonus it is giving off a nasty smell like it is going to blow up! It now gets really hot to

... Hoover U5344-900 WidePath Vacuum

I just bought a foldaway hoover with wide path. I plugged it in and started to vacuum and dust flew everywhere. Walmart would not give me my money back so they gave me another hoover foldaway with the wide path. I thought this one might work. This one does the same thing. It blows dust out the sides and you can't vacuum with it. Any help would be great.

Your Vac probably does not have a filter installed inside the unit, that is why fine dust escapes through the vents. Remove the dirt canister/cup from the unit and you will see a filter frame behind. Possibly the filter itself is missing or wrongly i ... Hoover U5172900 Fold Away Widepath Bagless Upright Vacuum

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u

Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0764 seconds