Having problems with your Vacuums ?

How far down do i push the attatchment hose on the reconery tank it is very hard to push down on the hoover shampooer


Answers :

You want the top of the attachment level with the top of the tank, this way it will create a seal so you have suction through the hose.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How far down do i push the attatchment hose on the reconery tank it is very hard to push down on the hoover shampooer


You want the top of the attachment level with the top of the tank, this way it will create a seal so you have suction through the hose. ... Vacuums

Hoover Jet and Wash 1500w S6254 001. Used once with great difficulty as assembly and use instructions are hard to follow.Now will not work as carpet shampooer at all, although assembly is correct as far as I can see and both motor and pump appear to be working and I am using the recommended cleaning fluid.Hoover website is no use at all in solving the problem.No cleaning fluid is being drawn up from the tank in to the cleaning fluid hose.There is suction from the suction hose so the problem appe


I am having the same prob my uncle got me one i cant find the manual anywhere to set it up the prob i have is where does the handle to make the water go out connect tooo ??? on the main pipe that sucks it back up i have tried every which way but not ... Vacuums

The suction is good, but it can't pick up most of the stuff on the floor. The hand held hose works very well, but it doesn't even pick up little fuzzies reliably when I push it along. And, the suction is too hard I think because it used to push easily and now I have to push really hard, even on flat carpet.


Check entire length of hose, including the piece in the power head, for clogs. Simply drop a marble in one end and allow it to roll out the other. If it doesn't, then the hose is clogged somewhere. ... Dyson DCO7 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC07 has recently been service and was making a clattering noise and very hard to push. We have taken it back and he has changed the clutch mechanism under the base which has solved the clattering, but it is still really hard to push because of the suction. It is even lifting the carpet in one room. Can you tell me what the possible reasons for this could be? One thought we had was that the little rubber wheels on the bottom cover could have worn so the hoover is closer to the floor


On the sole plate you should have 5 little wheels, these are prone to jamming after a while. You should make sure these are not jammed in anyway.\012\012You can release these with a screwdriver, but be careful not to prize too hard as you ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Shampoo-er This seems to be a common problem, the shampooer is putting out alot of water and hardly any suds. I read through the posts about the little filter that sometimes gets out of place and I think I found it in the box - is it about 1" diameter hard plastic ring around very fine mesh? If so where exactly does it go? Some posts say in the hose, and others say in the opening of the tank. Or does it go in the place where the hose attaches to the tray? I also found a round sponge in the box o


It goes on the small hole on the tank where the hose attaches to it. The sponge goes in the hole directly under the on/off valve. Here is a link to my online shampooer instructions.\015\012 \015\012 ... Kirby Ultimate G Bagged Upright Vacuum

Clogged hose... I have a clog in my hose, probably a sock, I have pushed it through to the hard plastic handle end of the hose, help! can the plastic handle wand be disconnected from the hose to remove the clog??? Thank you


Hi!\015\012 \015\012Low suction, poor pickup, or no suction may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor or a reduction in the spinning action in the Dirt Con ... Bissell 6594 PowerForce Bagless Upright Vacuum

Hoover Floormate Spinscrub Widepath Floor Cleaner hard to push


... Hoover H3044 FloorMate SpinScrub Wide-Path Hard-Floor Cleaner Upright Wet Washer

My self-propelled Hoover wind tunnel vac. cleaner is hard to push


... Hoover Vacuums

My hoover widepath tempo pushes easy in any hight when off, but turn in on and you can hardly push in forward. I took the beater bar off and cleaned everything and still having this problem


Make sure the beater bar is turning sometimes it will freeze up with dust and dirt will get inside the bearing caps on the end of the brush ... Vacuums

My Kirby shampooer - G4 - hardly used any water from the tank and no suds at all. Pet hair did blow out of the small slotted holes in the tray as I moved the shampooer back and forth, but the carpet was basically dry. I did vacuum before shampooing, so the brush part seemed to work great during shampooing, but no water! The small screen was stuck in the crook of the hose that attached to the tank so I did get that out and put it on the small hole on the tank, but it didn't make any difference. I


Few things:Make sure the sponge and the valve under the sponge (water tank) is clean.Make sure you follow the instructions (f you do not have the manual you can find one ... Kirby Ultimate G Bagged Upright Vacuum

Hoover F5809 Hello, I seen a few of your post and was hoping you could help me. I just became a member today. My sister gave me her old Hoover Steam Vac-Model F5809. This thing is so dirty and clogged because my sister has pets. So far I've gotten it all taken apart to clean it. I'm not a newbie and taking apart and fixing things. I have fixed things like microwaves, washers, dryers, dishwashers (still learning about TV's-very hard, hehe). Anyway, I got what I believe to be the motor cover off.


That cover is the called the fan cover and is usually pressed on. Tapping on the edge with a flat blade, you may be able to get it off and hope you don't bend it up, you will to put it back on tight enough so it will stay in place. Another thing to ... Vacuums

Can you remove the plastic hose that leads to the handle as mine has split. I thought i could remove it by pushing in the two black bits of plastic then shorten the hose. so far it wont budge. Is it meant to as Dyson sell the whole thing in one? cheers john


Yeah sorry it is sold as a complete unit and its a real pain to strip down so it better and faster to just buy the whole thing from dysons website  ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?


Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Self propelled vac: goes great on hard floor or hard slick carpet. Goes backwards fine but will not pull itself forward very well. Requires some effor to push it forward. I have adjusted the cable so the lever on the motor goes as far forward as possible. Suggestions? Model U6446-900


Dear Nasherrill,\015\012\015\012I've found a friend! I thought I was the only person in the world who owned the Hoover Model U6446-900! This model does not appear on the http ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My quite new neumatic henry hoover is really difficult to push - you need all your strength. I do not have the brushes down and its still really hard to push - can anyone advise? thanks


... Henry Numatic "" Canister Vacuum

HOOVER EMPOWER,PUSHES TO HARD - Hoover U5262-900 / U5260-900 / U5266-900 / U5268-900 EmPower Bagless Upright Vacuum


... Hoover U5262-900 / U5260-900 / U5266-900 / U5268-900 EmPower Bagless Upright Vacuum

My Hoover Windtunnel, 12-amp, UGG16-900 (or U6616-900 - hard to make out the "G"s from the "6"s) suddenly lost suction this morning. The dirt collection thing is completely clean (I always clean it out after using), the side filter is dirty but not destructively so, and I can see nor feel any obstructions in the hoses. Should I take it in (a real hassle in NYC) or get a new dyson? LOL.


Usually on this machine the door/valve assembly is to blame. if something gets caught in the door/valve assembly it can break this part. you can take it in to see what the est. would be. hope this helps ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Good Morning, A friend recently gave me her Hoover windtunnel model U630-900 vacuum. It is a self propelled vac. It comes on but is hard to push and will not really pick up any dust particles on the carpet. It has a funny smell also. I saw where one of you Q & A you said to check the roller brush. I thought maybe a belt may be off or something, but I do not have a manual to know where to begin checking. Could you tell what to check and also if there is anywhere online to download the manua


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

I have the hoover nano-lite and today when I put it on the carpet it is very hard to push. I never had that problem before.


You didnt set it to the right hight adjustment ... Hoover Vacuums

Hoover self-propelled windtunnel U6430-900 flat belt gets hot & becomes hard to push. It has a filter bag. Purchased 8/2/01. Took one plate off bottom. Used a compressor to blow out dirt & dust. Put new thin belt on.


Belts get hot when fibers from carpet get wound arounf the belts mounting shaft. Best to take a razor and cut off any fibers so the belt doesn't get hot again ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hi, I have a Sebo X4 which is almost 3 years old. I haven't had any problems with it until the last couple of days when I notice a slight screeching noise when in upright position, coming from the roller mechanism area. If I slightly push the sebo forwards it gets worse, if I tip it back it stops. If I take the roller out and switch on, there is no noise. I have always been careful not to tip the machine forwards when using the hose, but I recently lent it to a friend whose hoover had broken do


I dismantled the top part of the machine from the bottom and there stuck right down in the bowels of the tubes was a piece of card, a dress label! somehow it was only making a noise when the machine was in an upright position. It took a bit of stretc ... Sebo X4 Bagged Upright Vacuum

I have the bagless hoover windtunnel and it doesn't pick up anything and it is very hard to push. Changed the belt and The rollers are spinning and the filter has been changed. What else can I do?


It sounds like there are dirt and hair wound around the wheel axels cousing them not to spin freely. You have to remove all hair and carpet fiber. Then drop a drop of lubricant oil on the axel.\015\012Change the filter.\015\012You should ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

How do you use the hose attachment on the hoover shampooer


... Hoover F6021-900 Steam Vacuum

I've had my Dyson DC14 vacuum cleaner now for approximately 9 months and been very happy with my purchase. However, It is used sparingly maybe twice a week at the very most. The problem is when I try to use the item on my carpet, you have to push really hard to get it to move. It's as though the suction power is far to strong. It certainly doesn't glide as I think it should. It still picks up as usual but I cannot imagine that having to 'force' the machine to move is the normal operating procedu


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Is there a wrong way to attach the belt and the sweeper?? My Hoover Runabout is making a rubbing noise, like the sweeper is hitting something, and it's real hard to push.


Take off the belt . clean any hair from brush roller make sure movement smooth . re position belt and move by hand to make sure roller is not skew , , rubber is riding sideways and causing friction . ... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0846 seconds