Having problems with your Vacuums ?

How do I thread my singer1409 - Vacuums


Answers :

See the illustrated instructions beginning on page 11 of the manual: http://www.singerco.com/uploads/download/1256_1408-1409-(esf).pdf
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I thread my singer1409 - Vacuums


See the illustrated instructions beginning on page 11 of the manual: http://www.singerco.com/uploads/download/1256_1408-1409-(esf).pdf ... Vacuums

The beater brush on my vacuum appears to roll when I turn on the vacuum however, you only hear the actual sound of it on occasion and the vacuum is not vacuuming thread off the floor.


Greetings from GoVacuum,\015\012\015\012Your belt has probably been stretched to a point, the brush no longer spins when it touches the carpet. You probably can turn the machine over, and see the brush spinning, but it's probably stretch ... Eureka Vacuums

How do you thread a singer 95k10 - Singer Vacuums


... Singer Vacuums

How do I thread a pfaff hobby 741 - Vacuums


... Vacuums

How to thread lower looper of elnita serger - Vacuums


... Vacuums

Threading a brother 640D overlocker - Vacuums


... Vacuums

Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.


Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums

I replaced the powerhead drive belt. Now (2 times) while vacuuming the powerhead motor appears to run backwards. Because the metal pully which has left hand threads on it will backout / unscrew it self. Prior to this belt rerplacement it functioned properly. Thank You Bob


Look at your power head motor. If you see a fiberglass looking sleeve on the shaft where the belt attaches to it, you need to remove that. You can slip it off, chip it off, or break it off piece by piece. You can usually use pliers and break it into ... Rainbow 75th Anniversary Canister Vacuum

Thread at needle breaks when sewing. - Vacuums


Most common problem is the quality of the thread, most sewing machines require quality thread or else it breaks especially if the material is thick or hard ... Vacuums

How to thread a janome sr2000 - Vacuums


This sounds like a Sewing Machine problem? It is being listed under Vacuums-- I wonder if there is a better option for where you should list this problem, so that a sewing machine mechanic could see your problem. We fix Vacuum cleane ... Vacuums

How to thread brother lock 760D serger - Vacuums


... Vacuums

I need a riccar 925 threading manual!! - Vacuums


Voila!\015\012\015\012Click the link below and your manual will open in a new window:\015\012\015\012http://www.riccar.com/f ... Vacuums

I am replacing the fan on a sanitaire vacuum - I need to know if the threads are regular or reverse


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=562921\015\012Generic problem for all Vacuums\015\012I am replacing the fan\015\012posted by mchll_trvn o ... Vacuums

Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther


Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

How do I thread the Janome 372 bobbin - Vacuums


... Vacuums

Threading instructions Singer #29k2 - Vacuums


... Vacuums

The beater bar on my Dyson DC14 All Floors Bagles vacuum cleaner doesn't turn. There is no hair or thread caught up in it. All air-flow areas have been checked and there are no blockages that we could find. Any suggestions?


If it is not on the bare floor setting then you most likely have a belt issue it is not an easy fix I am sorry to say if your mechanically inclined I can tell you how to replace it. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Bobbin wont thread, spool does not move - Singer Vacuums


... Singer Vacuums

How to thread a singer 9540 sewing machine - Vacuums


... Vacuums

How to thread a singer 2662 sewing machine - Vacuums


... Vacuums

The vacuum cleaner does not pick up anything from carpet. It does not even pick up pieces of thread laying on carpet. On tile floors it blows dirt away instead of picking it up. I've tried all the settings on the brush and nothing works. It has done this since new


Sounds like there is a clog..\015\012\015\012Usually its in the hose - look closely.. Stretch the hose out straight and look in there good..\015\012\015\012Or a clog could be in the vac close to where the hose conects to the v ... Hoover U5269910 Bagless Upright Vacuum

Ho do I thread the Empisal EM 250 Bobbin? - Vacuums


... Vacuums

Brushes won't turn. have gotten out all thread etc, wound around the brush. have put vacuum in proper position and turned on the brush button


The brushes are usually driven by a belt that connects to one of the ends. They break. Check to see if yours has. ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

Will a singer 451k45 take 20 size thread? - Vacuums


... Vacuums

Thread a singer serger 14u454b - Vacuums


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0845 seconds