Having problems with your Vacuums ?
U8185-900 Savvy Do you sell the cord that goes from the head up thru the body to the switch
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
U8185-900 Savvy Do you sell the cord that goes from the head up thru the body to the switch
My Shop Vac 90L600A is getting electric thru the cord and into the switch, but it doesn't switch on when you toggle the switch from off to on. Is it a bad switch?
Check the othere end of the switch. You may have a brushes problem in the motor. You will have to check the switch while hot - be careful ... Vacuums
Power head motor is good,runs great from test cord switch seems to work. brush roll cleaned but power head motor will not run
If you have checked the power delivery down to the powerhead and you have current running to the powerhead, then you likely have a burned fuse. There is a fuse built into the powerhead motor and is usually located on the field winding. This is not ea ... Eureka 6831A Bagged Canister Vacuum
Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,
You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum
It will empty the cleaner but will not spray water filter is clean spray heads were taken off & i could blow threw them is it a case of no prime in pump if so should i fill pump i had this thing all apart and i now know evry inch of this matchine when i pull the triger it sometimes will spray for a sec.but thats it i also took the switch out and air goes threw when i press the switch if it is the prime in the pump how can i fill the pump . what hose on the pump will prime i thankx for your advic
The problem is most likely that your pump belt is worn, stretched or broken. Here you can get the belts you need and view the manual:htt ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
I have a DC 21 Dysonstowaway. Lately it cuts out a LOT, when vacumning . I press the start switch on the head, goes for 5 sec. Stops, goes, stops etc. How frustrating !! What can I do ?
Sounds like a loose power connection someplace on the machine.\015\012Probably needs to be looked at by an experienced repairperson.\015\012 ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Suction centralux vacuum two years old doesn't have the volume air movement it once had. Unit will still quickly reach an extremely high head of suction so no broken pipes. ran napkins thru no blockage, overode filter safety switch ran with out filter no difference. just don't move air like it used to
Hi!!! clean motor blower blades ,they collect alot of duct and the air in chopped,Good luck.Clean blower fan blades.. ... Electrolux Centralux Vacuum
Vacuum dead I have oreck XLx2 bagged upright - the belt ,plug and cord have been replaced - has been working great - now went to plug it in and it does not work - the light goes on in the on/off switch so power is working but vacuum is dead - any suggestions
If the cord coming from the bottom up to the handle is loose, and is a plug, push it in. If that doesn't help. then could be a problem with the motor. One other thing to check is inside the handle, maybe a wire came loose. ... Oreck XL2200 Bagged Upright Vacuum
The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu
This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums
I have bought a dysonmotorhead and when i switch it on the light on the head is green when i start to hoover it goes red can you tell me why
Check it for loose connections...clean evrything ... Vacuums
I have a clarke bench grinder model 1002. I have a light that I would like to attach into the wiring though the grinder wiring in it's base. The light has two wires, and the grinder has a ground that is grounded to the base, a black that goes to a switch then to the motor. The white goes directly to the motor. where would I have to splice in the two wires from the light? I have a switch that I would like to put in for the light on off also.
Attach the white wire on your lamp to the white wire on the grinder.\012Attache the black wire on your lamp to the black wire on the motor side of the switch.\012This will give the lamp power any time the grinder is turned on.\012Yo ... Vacuums
Power head attachment works great when plugged into the hose part of the vacuum. The problem is when I attach it to the tube for normal use there is no power. I have checked all the connections and switched the power switch on and off still no power from tube to power head. Is there anything else I can try? Model Callisto
Try having someone turn the machine on and off while you pull the cord in and out with the cord more angled towards the on/off switch. Sometimes these models have a break in the cord rewind and will not put the power through to the motor. ... Miele Vacuums
Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin
Miele vacuum Sometimes when I hit the auto roll up cord button or even move the cord, the power vacuum goes off. I move the cord again and it comes back on. I took it apart and looked at the connection from the cord to the auto roller. These are the electrical slip on type connections and are still in good shape. There are no bends in the cord. I air dusted everthing inside, put it together (with no extra parts!). Good news..it powered up so I did not break it, but it still has the same problem.
I have a Hoover Elite Rewind model #uh71009. We moved recently and it was jostled around and the red power switch popped out. I put it back in but it's stuck; it stays either left or right, it doesnt move back and forth. It appears there may be another piece missing from the power switch...all I have is the red switch and a tiny cylindrical metal tube with a spring on one end. This piece fits into the hole on the red switch. Inside the vacuum itself where this goes, there is quite a large cavity
Hoover Upright Vacuum model U5470-900 - The On/Off switch on the handle does not properly engage the power switch deeper in the handle assembly. It appears to ride over the lower switch and doesn't engage it to operate it. If I play with it, I can get it to maybe turn on the vacuum, but, then the upper handle switch won't turn it off. Our current workaround is to use the power cord for on/off operation.
... Hoover Vacuums
S444i just would not switch on. When I took it apart I sprung the rewind coil on the cord retracter and I can't get it back together. Now I have 2 problems!! It won't start and the rewinder
... Miele Vacuums
While replacing my power cord on my DC25 a spring popped out I have no idea where it goes. I need a diagram so I can see where it goes
Here is how the switch assembly should go together: ... Dyson DC25 All Floors Bagless Upright Vacuum
I have a ge light switch receiver rf1023, with incandescent bulbs, and when I try to switch it on it just blinks once and goes out. if I hold the switch on the battery-operated wall remote, the lights keep blinking until I let go. It used to work fine, and now it doesn't. I've lost the intallation instructions, so I don't know if there was a trouble-shooting section that covered the problem.
... GE Vacuums
I got this sewing machine , can anyone tell me what this control box is used for ?. It is mounted under the table in front of the motor,It says Control Box on the front and two push button number settings with can be adjusted up or down from ( 0 to 9 ) ,Next to these settings are two toggle switches. One is marked start with on and off and the other switch is marked end with on and off. Above these switches it it says Back Track . The tag on the box says ( Type LE -BB -24 - 110 - 220, 2
Still struggling with your model number. I understand from the added comment this is a Brother sewing machine. I was hoping to find a manual that would be of assistance. Here is a couple of websites that lists available manuals for Brother sewing ... Vacuums
I have an aerus electrolux guardian canister vacuum. The cord was damaged but the retraction winder is still fine. I have ordered a replacement cord but I have no idea how to remove the old cord and install the new one. Am I over my head?
The winder is activated by a coil spring located in a drum. The drum transmits the power from the wire with 2 circular contacts. To replace the cable you must dismantle the case to access the drum, take the spring pressure out carefully as to not let ... Vacuums
It won't turn on. I have partially disassembled it and have continuity between the power cord (wide blade) and one of the connectors where the switch assembly snaps in. Also, switch is working fine. There is continuity across it, then no continuity across its connectors when the switch is pressed. Not sure what to try next.
\015\012Please provide the make and model. Thanks. ... Vacuums
Sears 116.31913 Lower units, vacuum motor and agitator power head do not have power/115v to them and won't run. I'm trying to take the handle apart to access the on off switch. I've taken all observable screws out and cannot separate the handle and section immediatly below the handle to access the on/off switch, to trouble shoot. Any tips for separating the plactic pieces enclosing the on/off switch?
... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
Hoover power drive u6311 - How do u change switch? Does anyone have any idea how to remove the on and off switch, when I tap on the housing the motot and light goes on and off. Also does somebody have a exploded view of this model. also does anyone know the part number of the switch.
The swrtch is located in the bottom section of the motor. When the swtcih goes out it time to repalce the unit. The swtich is part of the motor. The switch rod run all the way down the body to the swtich located in the motor. ... Hoover U6311-930 Power Drive Bagged Upright Vacuum
Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?