Having problems with your Vacuums ?

On/off switch on Henry

\015 I have tried to replace this switch of four terminals but on putting in the new switch I have forgotten which cable goes where! There is a brown (live)and a blue (neutral) with two white cables coming from the motor.It is quite an old Henry and has only one speed.Can you tell me which one goes with which one, please?Thank you\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When i switch my henry hoover on it works fine for exactly 50 seconds then switches of for approx same time then comes alive again for 50 secs and so on...driving me nuts.

... Vacuums

Henry will switch on and stay on, only while the switch is pressed.rnHow can you get at the switch to replace it? There seem to be many crosshead screws under the motor part,- which need to be undone? Thank you.

Sweeper shop to get switch, you could have a wiring problem . Take casing off and check out and get those screws out of there they could cause some damage all while unplugged of course.bare wire coud cause your problem and thoe screws hopefully arent ... Numatic Henry Bagged Canister Vacuum

On off switch broken on my henry hound vaccum cleaner, where can i get a new switch?

... Numatic HHR-200 Henry Hound Bagged Canister Vacuum

Henry's switch has come out.I found the red switch and 2 bent bits of metal. How do they fit together to make him work again?

Rather than coming out, it sounds more like the switch has come apart. It also sounds like you haven't got all the bits. Even if you'd got everything, and knew how to assemble it, there's a good chance it will come apart again anyway. The only safe t ... Numatic Henry Bagged Canister Vacuum

The main switch on my Henry will not stay down. How do I rectify this? I have undone the three screws inside the top but cannot get the top off to gain access to the switch.

... Henry Vacuums

On/off switch on Henry

... Vacuums

Henry hoover wont switch on

... Vacuums

Henry hoover won't switch on

... Henry Numatic "" Canister Vacuum

Henry Hoover throwing trip switch in house

Sounds more likely to be the switch than the motor, especially if it is the model with the top switch rather than the side "rocker" switch. If you are in the UK, speak to the technical people at ... Numatic Henry Bagged Canister Vacuum

Bypass switch on a henry hoover

... Numatic Henry Bagged Canister Vacuum

My henry vac switch is dead.

You will need to remove the top cover of the vaccum by removing the 4 screws underneath.The you need to test with a multimeter if you have 240 volt power to the bottom of the switch. If you haven,t power there you will need to check the plug connecti ... Henry Numatic "" Canister Vacuum

I have a Henry 200 and the red on/off switch is stuck in the on position can it be fixed

Well... It probably can't be fixed, but it can easily be replaced. Depending where you are, spares are usually readily available.\015\012If you need more guidance, please post here again, and I'll see what I can do to help.\015\012Good luck! ... Numatic HHR-200 Henry Hound Bagged Canister Vacuum

Rewireing a new switch diagram on henry - Hoover Vacuums

This video may help you ... Hoover Vacuums

My henry hoover will not switch on - Vacuums

If you have an elcrical tester you can verify that your source of electricity is in fact working.next test that the power is getting to the switch.check that the switch is working properly.If you have power all the way to the motor but it sti ... Vacuums

My henry hound turbo head switches off after about 30 secs use any help greatly appreciated thanks

... Numatic Vacuums

I have use my henry with no problem, tunred it off with the red switch on the top, 20 minutes later I went to use again but the machoine was toatlly dead with no power I have changed the plug fuse

Could be fault @ plug.. try cutting off 10 mm of cable then redo plug ..Replace fuse then try, if still dead try switch, you could short this out or if you have multimeter check for contact...if stii no action could be motor.... ... Vacuums

My henry hoover is stuck in the hi suction function, I have changed the hi-lo rocker switch with a new one, but it still will not alter the power of the suction. Any other suggestions what I can check?

HI I have the same problem, and actually did the same thing to fix it..any ideas yet? please [email protected] ... Henry Numatic "" Canister Vacuum

My Old Henry hoover is making a VERY loud noise when switched on! Its still works but very loud, please help!

Most likely the motor bearings have worn out. You can fit a new motor quite easily, but if you need to pay someone else to do it for you the labour plus motor cost will probably make the job uneconomical. Sorry to be the bearer of bad news... ... Numatic Henry Bagged Canister Vacuum

On off switch broken on my Henry numatic Hoover

... Vacuums

Henry vacuum high low switch does not work on low

... Vacuums

Henry Hoover hvr200/20 wiring to red switch 4 pin

... Numatic HHR-200 Henry Hound Bagged Canister Vacuum

Electrical Burning Smell from Henry HVR200 Vacuum Cleaner

Hi! Highly unlikely that you need a new motor.  Highly likely that you need new carbon brushes.  The smell is caused by excessive sparking between the worn brushes and the copper commutator segments.  Most carbon brushes (and from memo ... Numatic Henry Bagged Canister Vacuum

Numatic henry keeps cutting out & plug crackles in the socket!

It wasn't the hoover, it was the plug socket! ... Numatic Henry Bagged Canister Vacuum

Henry's motor burnt out

Henry numatic: 2 white wires do these go opposite or side by side ... Henry Numatic "" Canister Vacuum

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work

It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0234 seconds