Having problems with your Vacuums ?

The rear wheel on my dyson dc01 has come off. i have been sent the real wheel fastner retaining pack but do not know what to do with the bits. There are two metal rings and two semi circular black rings. Can you help?


Answers :

There is a small groove in the end of the stud on the vacuum that the wheel fell off of.
\015\012Slide the wheel back on the stud, put the washer on then put the ends of the half clip in the grove on the stud pushing on the back of the clip with a small screwdriver on the clip to lock it back in the groove. The old parts may be still in the wheel if it rattles. There should be a plastic cap on the wheel like a little hubcap, pry it off with a screwdriver carefully so you can put it back on after the clip.
\015\012Please rate this solution if it helps you.. Thank You....
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The rear wheel on my dyson dc01 has come off. i have been sent the real wheel fastner retaining pack but do not know what to do with the bits. There are two metal rings and two semi circular black rings. Can you help?


There is a small groove in the end of the stud on the vacuum that the wheel fell off of.\015\012Slide the wheel back on the stud, put the washer on then put the ends of the half clip in the grove on the stud pushing on the back of the clip with ... Vacuums

I have the IROBOT discovery that just got a new battery. IT ran great! As the battery was dying, I put it into the home base. The "brick" is green, the home base has two green lights and the on/off pulsates red. It never charges though. Eventually the red light stops pulsating. Customer service said to reset it, clean the metal, and nothing works! They told me to just buy another one. The problem is that I know it was working! Help!


The best thing that you can do is take the charger into somewhere that can test it for the proper output voltage. It should be somewhere very close to 22 volts with no fluctuation. The charger is the easiest thing to test in this case. ... iRobot Roomba 4210 Bagless Robotic Vacuum

How to wind cord onto spring loaded retractable cord reel for a Kenmore canister vacuum. There is a metal 'U' shaped, spring loaded, piece that fits over the outer aspect of the wheel. If cord needs to get wound on under this metal band I can't figure it out and the band is like factory sealed onto the wheel. Also. I don't know which direction to feed the cord onto the wheel


What is the exact model # please?Thanks!! ... Kenmore Vacuums

Wiring diagram took wires off motor and do not know which goes where.There are two main from plug in one whit one black then two of same coming from light in front.On the motor ther are more terminals than wires.On diagonal corners there are black dots.Can you please help this cost 800$ and do not want to burn the motor due to crossing pos and neg.Do you have a picture or know where I can find?


... Oreck XL21 Bagged Upright Vacuum

My plunger (bought in Chile) has 1. a metal filter, 2. a convex (not flat) metal disc with central hole for rod, 3.a metal disc with holes of two different sizes in circles radiating from the centre 4. plunger rod with screw and 5. a spirally coiled wire forming a circle. I cannot figure how to fit these especially the coiled wire. Help appreciated. Thanks


Place the coil in the hole and turn untill reach the desired height. ... Vacuums

I have the brother Ls-2000 sewing machine i threaded the top as well as the bobbin but when i try to sew the thread gets stuck and it bunches up and tangles in the bobbin. also the little bit that did sew was tight stitches on one side of the fabric but very loose on the other side I followed the instruction and it keeps happening i need help i dont know how to fix it please help me


Adjust your tension.You probably did not wind your bobbin properly as well.Make sure you oil your machine every month or so and make sure your bobbin is seated properly before you sew.\012\012Go slower with the pressure foot speed and use the r ... Vacuums

Hoover problem the wheels on the bottom of my upright have come off , i have put them back on but i do not know where the metal clip should go and also the height ajuster for the wheels does not work, any ideas thanks kevin oates


The metal clip is a leaf spring and there is a slot for it, You may have to pull the cover off, may have a broken piece for the adjuster. Would help to have model number. ... Vacuums

I have an L shaped piece of metal with a hole at one end that fell out of my hoover elite bagged upright vaccuum cleaner. I repaired the belt but don't know where this metal piece goes. I think it has something to do with the wheel assembly which is replaced and it seems to want to stay there. any thoughts


This metal clip was for the wheel assembly, but not always needed. you can diregard the part if your vac is working correctly with the front wheels. ... Hoover Elite U5061-900 Bagged Upright Vacuum

My dyson has two gears as it were! One for normal suction and the other for deeper cleaning. There used to be a real difference in the performance between the two options, also the noise changed when you swithched from one to the other. This no longer occurs. I have taken it apart according to your instruction, cleaned all the various bits but still no luck. The cat fur is still clearly visible despite my best efforts. Can you please help!!!!


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Turbin hey its me Lisa I took the turbin apart and know where the wheels (gears) go but they have this little bearing or what ever it is its round and has a whole thru sent can't figure out how it goes to put it back together. the thing turns really good now after I soaked it HELP


You should have it all back together now. Hope it is running ok. \015\012Lauren(reddevil6) ... Hoover F7220900 SteamVac V2 Upright Vacuum

I recently ( approx. 2-3 months ago ) purchased a dirt devil. Now it is not picking up properly. When I push vacuum forward it picks dirt up a little bit, when I pull it back all the dirt falls out of the bottom. I replaced the filter today and it has not solved my problem. I dont know where my warranty is. Can you please help me?


Hi sounds like your line is stopped up somewhere , check ur suction an make sure your brushes are spinning, if they are try a wire clothes hanger to the hose at the bottom hose to dislodge anything that mite be stuck ... Dirt Devil Vacuums

I have a genie hoover and would like to know how I get the purple bit back onto hoover as I emptied the filter and I can't get it back on need help fast???


... Vacuums

The kick stand that lowers the vacuum when in use got in a position where the red foot pedal would not come back up to bring the wheels down and the vacuum rest in the upright position. We took it apart and corrected the position, but the side with the small circular spring came out and we are not sure how to attach it back, exactly where it hooks onto. Can you help show us where it goes?


... Dyson DC25 Animal Bagless Upright Vacuum

When I took the base cover off the vacuum to clean the roller, a metal piece that is bent in half, as well as a white plastic stick piece came flying out. I think it might have to do with holding the vacuum in an upright position, but I don't know where it goes. Help!


They go in the slot beside the right wheel. Metal spring first, (the open ends facing away from front of vacuum base. The white nylon piece lays parallel and directly on top of the metal spring, round edge up, and aligned with the open ends of the me ... Eureka 411A Upright Vacuum

I have a electrolux 7000 my cord brok off and it got succked in. igot it apart. I DONY KNOW HOW TO PUT THE COIL SPRING ON THE POWER CORD WHEEL. NEED HELP


This is very difficult to reassemble correctly, and more difficult to explain properly. You need to take the vacuum to the nearest authorized Aerus Electrolux store for reassembly. Or call for free pick up and delivery.\015\012\015\012 ... Electrolux Lux 7000 Bagged Canister Vacuum

Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?


Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum

I hope you can help a do-it-yourselfer. The paint inside my microwave is beginning to peel and chip off on the bottom under the circular wheel track that facilitates the movement of the round glass plate. Could ignoring this start a fire if I continue to use the appliance? With exactly what product and how can I fix this? Thanks.


Hi\015\012\015\012If you let it stay without re-painting it then it can arc, which will greatly accelerate the charring & rusting processes. If the metal under the glass plate of the oven is chipped or charred, it will have to be sanded s ... Vacuums

Hoover 2000W dust manager cyclone- Have had this for about 2 months and the brushes stopped turning thinking that the belt had acme off turned it over to try to get in to look at belt now the bottom wheels have came off and will not go back on have not lost any bits literally just undid one screw! Please help!


... Hoover Vacuums

Hi There I have got a Kirby 2 HG vaccum cleaner which is around 20 years old now. It was going really well until last week when one of the capacitors which are connected to the brushes blew up. There is two capacitors one for each brush. One of them completely blew to bits and the other one is still intact. My question is are they the same size and where do I get a new one from. I know it is an old machine, but I would like to fix it and get it going again. Any tips???


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=541405\015\012Generic problem for all Vacuums\015\012Hi There I have got a\015\012Posted by opfinder on Apr 24, ... Vacuums

On my Eureka Model 1759A (from mid-1980s), the plastic catch that holds the two parts of the metal body together has broken. I would like to replace the part of the catch that attaches to the top (the part with the lip on it), but I can't find the part online ... or even a drawing. Where can I get this part ? ? ? HELP ! ! !


This latch is riveted to the body. If you are lucky you may find an old Eureka warranty/ repair center with one on the shelf, or another canister for parts. That will be your best hope. ... Vacuums

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.


Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums

My Hoover SteamVac has been doing a wonderful job but in two instances, after emptying the dirty water and reattaching the reservoir, the machine has lost suction. The first time I was able to make it work again after taking it apart and putting it back together about 10 times. I don't know what I did that fixed it but as long as it worked again, I was happy. But it's happened again and I can't get it to vacuum. I can see that it isn't clogged. Can you please help me????


Look for the lower tank filter to be clean. also make sure the lower tank lid is on properly. latch when installed on machine. Make sure the front panel duct is on the lower tank. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Have Model HFQ15A but lost directions. Need to know what the two dials on top of fa n/heater are all about and how to best use this product. Thanks for your help.


... Vacuums

My Triton T80 SI shower is leaking from where the outlet pipe assy joins to the heater can assembly. when I checked where the two join together I see that there is a rubber O ring fitting into a recess in the heater can assy. The screws which hold the two parts together does not force a compression between the two parts causing it to leak. Is there another modified unit or am I stuck with what Ive got and should I replace the O ring or the shower.


... Vacuums

After removing the filter, I cannot get to battery on the Dirt Devil Kone M0213, there are two horizontal screws. Removing them does not help getting to the battery, no way to remove the insert where the battery is located.We have two of these, however they did not come with a manual for dis-assembly. Please help or proved a diagram on how to remove the battery. Many thanks, Wesley Lennon


Sheesh, did anyone actually read the person's question? It's about the battery, not the filter.\015\012\015\012You have to get the outer cover off and it's not easy. There are four tabs which need to be released. I have to use a very sha ... Dirt Devil KONE Hand Vacuum MO213BLU Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0541 seconds