Having problems with your Vacuums ?

We have a Bissell Proheat Cleanshot 2X Model 9500 Steam carpet cleaner. The first time we used it things were great. The second time we used it it left tracks in the carpet. We have no idea what caused this. We tried using the machine on an entirely different carpet and it did the same thing. After vacuuming the carpet about 10 or 12 times, the tracks are still embedded in the carpet - HELP!!!! We're read and reread the manual and contacted customer service and received no help.


Answers :

First things first. It's only the second time you have used the machine, so it must be fairly new. If you have a receipt and the unit is less than a year old you should take it to an authorized Bissell repair center and have the machine inspected under warranty.
\015\012
\015\012Otherwise, The jets on this unit clog easily, there are two of them and you can locate them under the recovery tank towards the front of the machine, and blow them out with an air compressor. To prevent the jets from clogging in the future make sure to flush all shampoo out of the machine with clean water when done using it. That is most likely your problem.
\015\012
\015\012If it is leaving black streaks on your carpet it could be coming from a burnt belt or melted brushroller part, in which case inspect the belts and brushrollers and replace the damaged pieces.
\015\012
\015\012I hope this helped
\015\012
\015\012Good Luck
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a Bissell Proheat Cleanshot 2X Model 9500 Steam carpet cleaner. The first time we used it things were great. The second time we used it it left tracks in the carpet. We have no idea what caused this. We tried using the machine on an entirely different carpet and it did the same thing. After vacuuming the carpet about 10 or 12 times, the tracks are still embedded in the carpet - HELP!!!! We're read and reread the manual and contacted customer service and received no help.


First things first. It's only the second time you have used the machine, so it must be fairly new. If you have a receipt and the unit is less than a year old you should take it to an authorized Bissell repair center and have the machine inspected und ... Vacuums

I recently purchased this vacuum after reading consumer reports article on it and from recommendations from family. However, since I've had this vacuum it's been nothing but problems! I have a frieze carpet and I have the vacuum set on the highest setting. Each time I use it, the vacuum clogs with carpet fibers before I even finish a room! Any suggestions?


Is that a shag carpet? the power head is raised up all the way can you lower the suction on it is the carpet old the vacuum may not be able to handle the carpet,go to a vacuum store and see if you can try somthing else out some stores well let you re ... Hoover Tempo Widepath Upright Vacuum - Blue

Whistling noise I just bought Dyson dc 33 multi floor plus about a month ago and use it 6 times because the carpet get dirty / dusty so quickly living with 5 other people in the house and when I use it today by stepping on the foot thing to make it to go down and when I push the botton it makes the whistling sound why is it like that I have read every instructions several times , does that mean I need clean the filters or need to get it fixed . When I first used the vacuum it was not like that a


... Dyson DC-33 MultiFloor Upright Vacuum Cleaner

I have Hoover WindTunnel Air Upright Vacuum - UH70400 just used couple of times. While vacuuming the carpet carpet fringes were rolled up in to brushroll and brushrol stopped working. It means vacuum is not working effectively now. Brushroll indicator is flickering.


... Hoover Vacuums

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?


This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Vacuum clogged Just had new carpet installed. In trying to vacuum the carpet for the first time, fine particles have clogged the sweeper. I'm using a rainbow sweeper with water reservoir.


If you are talking about the electric hose, try using your none electric hose with the crevice tool attachment to extract the particles from the other one. When using any of the hose please leave it running a few minutes to make sure everything in th ... Rainbow E series Canister Wet/Dry Vacuum

My dyson vacuum cleaner doesn't seem to have the same suction power it used to. I have cleaned out the canister and have taken apart the vacuum head (for cleaning carpets) and it doesn't seem to be blocked but it seems to lose suction by the time it reaches the head. The suction is strong at the end of the hose (where you attach the telescopic attachment with vacuum head) Any ideas? Thanks, Irene


... Vacuums

I received my dirt devil canister vacuum - vision pet for Christmas and have only used it several times. I am having trouble with it not suctioning very well. I have the max suctioning turned all the way up. It hardly picks up anything at all now. I can't seem to find my instruction manual. What's the problem?


Change out the bag. Check the internal air passages for blockage. Check air flow without the bag and pick--up hose in place--should be quite forceful. Attach the bag and try again. If ok, attach the hose and try again. At some point, you should find ... Vacuums

Sometime when I am vacuuming carpet or a large area rug, my Dyson starts making this loud, horrible, wrenching noise. It stops when I lift one of the wheels up. What is causing this? I have only used my Dyson 3-4 times.


You will need to have the clutch replaced. this is causing your problem. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Last time I used my Bissell Pet Hair Remover vacuum it smelled like something was burning and it left a black mark on the carpet. What should I do?


When you smell burning like that it usually indicates that the belt is worn and slipping on the motor shaft. You probably need to change the belt. You can get the belts for your model here: ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

Lost suction I've only used this vacuum a few times, it's practically brand new. Now, one I turn it on, it sounds fine, and the hose feels as if it's getting some suction, but it's not strong enough to actually **** things up from the carpet into the canister. I have completely emptied the canister and bought a new filter. Nothing seems to help.


TOSS IT and forget it! I have never used a hand vac that worked that was worth the effort of turning it on .... I suggest they are all junk ... I found very few vacuum cleaners ... actually **** especially anything made by dirt devil ... I do have a ... Dirt Devil Vibe AllPurpose Hand Vacuum Bagless Vacuum

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK. Mine is so loud I can't use it very long-high pitch screech. Can this be fixed or does the whole vacuum need to be replaced? It still cleans gr


Sounds like a bad motor. Could be either foot motor or main motor either way cost will be more than half of the unit. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Using a Hoover Steamvac to clean my carpets. It works fine in some areas, but others it makes a clicking noise and stops sucking water. Once I turn the vacuum off and wait a few seconds, it clicks once more and is okay to use again. Certain parts of my carpet this happens so frequently I can't vacuum.


1)clog in the hose or air/tank full you must , need replace or emptied,test the belt for broken or worn.2) noises can be area motor , test for fan blade defective or broken3) You must go http://hoover.com/support/video-instruction-guides/ for ... Vacuums

My electrolux oxygen vacuum cleaner shut off and will not turn back on. It's less than a year old, but I bought it off Craig's list--they were the orginal owner and they said they bought it in May of 2008. I've only used it a few times and it worked fine except for the last time when it suddenly just shut off. I thought maybe it had come unplugged and I didn't really worry about it because I was finished vacuuming. But, I went to use it tonight and it would not turn on at all--no lights, nothing


No..Electrolux is really great about warranty service. They will help you even though you are not the original owner. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

My Bissell Pro Heat Select 2X does not pull up the dirt from the carpet into the water. The water just slowly disappears. The first time I used it the water got really dirty. The very next time I used it it worked differently and the water just disappeared until it was all gone. I've only used it a couple times and I don't see where it is working. Has anyone else had this problem?


Inside the plastic suction lid is a little red plastic filter that has to be cleaned out every time you use it because it sounds like your vaccum is not picking up all the hair and debri before you clean the carpet causing the water to be injected in ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Just bought and used the Hoover MaxExtract 77. First time the water was extracted from the carpet. Second time NO water in tank. Now I have wet carpet. I've taken the machine apart 3 times and cleaned the filters and still the water is not extracted from the carpet.


... Hoover F6055-900 SteamVac Maxextract LS Wet/Dry Vacuum

Carpet vacuum attachment quit working after sucking up a bedskirt. Bedskirt has been removed but carpet attachment will not work. My old vacuum had a reset button on the carpet attachment for use when the carpet attachment sucked up something and turned off. Does the Hoover have such a feature, and, if so, where is it? If not, how do I fix the problem and how do I keep it from recurring? Model # S3765-040. Serial # 100700081298. Purchased 2/08.


I have a Hoover Conquest approx. 4 yrs old. The turbo head is not working Model No. PB4 230-240V AC 50Hz 200w CS4901N (N127) I have been trying to locate another one or another one similiar to fit my machine ... Hoover Vacuums

I have a Simplicity S24 canister vacuum. It's about 3 yrs. old. In the past year I have had it in the shop 4 times because when using the rug piece, the piece turns on & off, on & off. The actual vacuum doesn't... just the rug piece. I recently spent $65 on a new part, after spending countless dollars the other 3 times it was in the shop for this problem. I'm ready to buy another name vacuum altogether as I feel this vacuum is not worth the money that was spent on it. I'm very frustrated.


Repair shop has not fixed the problem? complain until they fix it properly. This is a pressure fault / jamming issue or slipping drive. Repair shop should have fixed it 1st time. ... Vacuums

Suction problem I have a Hoover Widepath Fold Away, 12 amp motor vacuum cleaner and the problem I am having is every time I vacuum, the vacuum gets clogged up with carpet. I am probably only able to do one stroke then it gets clogged and I have to stop and unclog it or it spits it out on the carpet. This is very frustrating and I don't get much vacuuming done. Please can you help me. Thank you. Gwen email is [email protected]


Get rid of the carpet its shredding and falling apart.no sence in vacuuming old rotten carpet.or try using a vacuum without a brush roller and just suction ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

I have a Hoover Elite Rewind vacuum. Actually,this is my second one. However, after about 4 months of use, it emits a "sour" smell when I'm using it. I empty the cannister before each use and clean out the filter monthly. My house has mainly hardwood floors, so I typically only use it on area rugs and 2 small carpeted rooms. Is there any way that I can get rid of the smell? I've tried putting a dryer sheet in the cannister, but this gets stuck in the filter mechanism. Also, carpet fresh clogs th


Does it smell like an electrical burning odor? could very possibly be the motor going bad already. ive seen it happen. but if not try freshwave odor absorbing pearls. i carry it in my store and we do have shipping. Truly the only thing you should use ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

My bissell proheat 2x carpet cleaner is not spraying from the bottom or sucking up when turned on. The hand tool works just fine. I have made sure it was on floor cleaning when I used it to try and clean my carpet. the busshes are working but nothing else is happening this cleaner is about 21/2 years old and has only been used maybe 5 times so it has not had alot of use.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

We have a Kenmore Progressive Model 116 Upright bagged vacuum with Hepa filter. It's at least a couple years old. For quite some time now when ever we use the vacuum the vacuum motor will shut off nafter about 5 min. of use. We then need to let it sit for awhile and then we can run it again for another 5 min. The bag has been change. Any one have any ideas how to fix this?


I suspect that you have a restriction. The motor sounds like the thermal break is stopping the motor before damage, due to heat.\012You must witness that the entire suction and discharge side are clear. This is not always very easy, but necessa ... Kenmore 34612 Bagged Upright Vacuum

The carpet cleaning portion of the vacuum sucks debris up poorly, and during the whole time I have it on carpet, the hose continues to have strong suction. The vacuum also spits out what its vacuumed up.


The screws along the base of the vacuum must be removed . The vacuum cleaner cover must then be removed exposing the suctioning hose syphoning the debris from brush roll area. Pull the hose from the brush roll area letting it hang freely. Remov ... Vacuums

I purchased a brand new Eureka Pet vacuum, sorry don't know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage


If the motor is running, there should be suction. Possible problems depend on whether it's a canister or upright and are:\015\012A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out ... Eureka Vacuums

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK.


Sounds like a bad motor bearing. If it is, then you would have to replace it. Could be the brush roll, did you check the ends to make sure they turn easily? ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1268 seconds