Having problems with your Vacuums ?
Changeing belt how do you install a new belt?
I have an Eureka, The Boss, bagless, upright. The brush is hardly rotating. I think it could be the belt but i cannot open the vacumm to check it. How can I fix this?
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Changeing belt how do you install a new belt? I have an Eureka, The Boss, bagless, upright. The brush is hardly rotating. I think it could be the belt but i cannot open the vacumm to check it. How can I fix this?
I HAVE A BISSEL 5200 FLIP IT AND WHEN CLEAN WATER TANK IS ON THE MACHINE AND IT IS BEING USED AS DRY VAC ALL THE SOLUTION LEAKS OUT. I TRIED TIGHTENING THE CAP , I CHECKED FOR CROSS THREADING , I HAVE TRIED EVERYTHING I COULD THINK OF THAT IT COULD BE NOTHING FIXED IT. MY FRIEND HAS ONE AS WELL AND HERS DOES THE SAME THING. IS IT A MANUFACTUER DEFECT?
Yes, they pretty much all leak, that can be chalked up to lousy manufacturing. Sorry. ... Vacuums
Hi,My agitator brush won't run on my hoover S3590, I changed the belt, that didn't work. I don't see a possible cause in my book except replacing the belt. I think there could be a short, the brush will come on sometimes when pulling back and slightly lifting. Any ideas would be great and can I fix it myself? Thank you for any help, Bobbie
Hi Bobbie\015\012Take apart the electro floor head if you can and inspect inside - it may well be that there's clogged dust preventing the brush from turning and also check both sides of the actual beater bar as thread and tangled hair can often lead ... Hoover S3590 Bagged Canister Vacuum
I have a Sanitaire model SC886 upright vacuum. It's about a year old. I replaced the belt , cleaned bag , checked for blockage in impeller fan and now it makes a noise , like a grinding noise or something . Could you tell me how to fix it ?
The bearings in the motor needs to be checked,or the impeller is damage. ... Eureka SC886 Bagged Upright Vacuum
The roller in the power head will not rotate-- replaced belt & that is not the problem--now what do i check? the right end will move, but the left end seems fixed-- is that correct?
Sounds like the bearings froze up. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
The brushes are not rotating - checked the belt no problem - what else could it be?
Assuming a drive pulley is not loose and the motor turns, try turning the brushes by hand. If they require much effort they may be jammed by dirt. My cat is a constant culprit! ... Eureka 4700A Maxima Bagless Upright Vacuum
KENMORE 27614 CANNISTER VACUUM The roller vacuum brush does not rotate. I check the belt and it is fine. Waht could be the problem?
... Kenmore Vacuums
I HAVE A DYSON DC07 I HAVE CHECKED ALL HOSES AND PLASTIC ATTACHMENT SECTIONS , CANNOT FIND ANY BLOCKAGE ANYWHERE IN THE SYSTEM .THE BELT IS GOOD AND THE BEATER BAR IS ROTATING WELL , BUT THIS VACUUM WILL NOT PICK UP ANY THING. I DID NOTICE THAT THE HEPA LIFETIME FILTER IS BLACK AND NOT SURE IF IT CAN BE WASHED OR CLEANED. THANKS BOB!
I have just cleaned mine just a half an hour ago - SAME PROBLEM !!\015\012ok take the dust cylinder off the vacuum cleaner and take the plastic clear cylinder off - there is a clear clip one side and you might need a small knife to unclip other ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it
The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum
Just bought this Hoover Fusion vaccum used, cleaned it up, checked belt and filter, turned it on and is extremely loud, almost like a scream. Any idea what could be causing this and how to fix?
Loud noises from this model are caused by dirt build up on the suction fan mounted directly to the motor. Under the dirt cup there is a filter screen that should have a foam filter insert, when not used or cleaned properly allows dirt to get into the ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum
I have the scunci 1000 steamer- it was sitting for a while and the cap on the top looks like its corroded and i cannot remove it from the steamer - i just bought it a year ago, but i think the salt or vinegar from cleaning it got trapped in the top and i tried everything i could think of to loosen the top so i could pour water into the unit and use it again; otherwise it is in perfect condition, but i tried even pliers and i cannot loosen it and i dont want to break it, but am so frustrated - wh
Hi, Elaine, W/D here.Corroded items are difficult to break loose as the corrosion builds up a layer that binds the parts together. Try this, as I usually have good luck with this method:Tap around the perimeter of the cap with a wooden h ... Scunci SS1000 Handheld Steam Cleaner
I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.
... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
Bristles quit rotating and smelled like something was burning. It isn't the belt that turns the bristles. Can't afford a repairman, can you help me fix it?
Belt can reamin intact but still jam and burn. It won't necessarily break. I suggest you remove the bottom of the vacuum where the bristles spins and where the belt is located. You may have something jammed in there. You may need to remove the bristl ... Bissell 6594 PowerForce Bagless Upright Vacuum
How do I get the beater brush off of the vacumm to replace the belt? The vacumm is a Shark roadstar . I can get the belt on the one end but I cannot get the brush up to put it on that end. Judy It is a Shark Roadstar EURO-PRO Model No. UV208C
Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430
Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum
Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the
... Dirt Devil M088905 Vision Bagless Upright Vacuum
Belt squeels when the roller starts turning. only used about 10 times. Small belt under cover is very loose, but it shouldn't be worn out after only about 10 uses. does the small bell just rest on the belt control pin or is it supposed to be around it (thinking it could have slipped off)
Ours did the same thing in about 10-15 uses, the idler pully quits holding the v-belt tight and the the aggitator wont turn. ... Hoover U5194-900 Mach5 Multi-Chamber Cyclonic Vacuum Cleaner Bagless Vacuum
Hello i own the bissle proheat steamer it turns on but no water or soap or suction from floor or the utensiles ive taken the take off the back to scope out anything that could be in the way but dont see anything the motor is making that clogged vacume noise witch makes me believe something could be stuck somewhere in it but it could also be no water is getting to the pump or despencer but the brissels still work belt for that is good where would i be best to check and where is the location of th
... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
Good Morning, A friend recently gave me her Hoover windtunnel model U630-900 vacuum. It is a self propelled vac. It comes on but is hard to push and will not really pick up any dust particles on the carpet. It has a funny smell also. I saw where one of you Q & A you said to check the roller brush. I thought maybe a belt may be off or something, but I do not have a manual to know where to begin checking. Could you tell what to check and also if there is anywhere online to download the manua
... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum
The roller on my Dyson vacuum has stopped rotating (I still have suction) I have checked the belt (not Broken) and have checked and cleaned the roller and spindle and also checked the "auto" button setting on the vacuum but to no avail ... Anybody have any clue as to the problem Many thanks
... Dyson DC07 Bagless Upright Cyclonic Vacuum
I have a dyson animal and the brush will not turn i think it is the belt how do i check the belt or change the belt
Hello. In most instances, the problem is the belt. the problem with dyson, as all vacuum repair people will tell you is this. All other brands make it easy to change the belt. Usually for $5. or less. Dyson put the belt inside of an assembly whi ... Dyson Vacuums
Hi i have got a Dyson dco4 it switches on but the roller doesn't go round. I have checked the belt which has gone so I have no idea what else it could be please could you tell me what else it could be
If the belt is gone, then you need a new belt. Otherwise, ensure floor select switch is set to ON.\015\012\015\012If you don't have a user's manual, you can use the below site to get one free.\015\012 ... Dyson Vacuums
Burned smell hi, I have used my hoover 4 times and is starting to smell as something burned, I checked the troobleshouting part of the owner manual and it says that check the belt, I already did that and everything is ok I used the hoover again and still smelling bad and start to work very slow I better shut off it.. what could I do??
If the motor slowed down this would indicate a bad motor. not cost effective on this model to replace unless under warranty. it is not uncommon these days to see a motor go bad every now and then.\015\012\015\012What are the first 4 digit ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum
My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a
Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Roller brush does not rotate if there is a belt I can't open that part of the vacuum to look. Vacuum is new but I vacuumed a string that caused the brush to stall for a moment. I could smell like when a belt gets hot or burns it's a surfacemax 300.
You need to replace the belt. Replacement Vacuum Belts ... Vacuums