Having problems with your Vacuums ?

Replacement motor I purchase a replacement motor for a F5897-900 Hoover SteamVa Motor part # 43576197 or 27242051. The replacement motor has three electrical connectors + ground were as the orginal has two electrical connectors + ground. Do I ingnore the the thrid connector and hook up the wires to the same connectors as the orginal or do I have to do some rewiring.


Answers :

The manual only show one wire from the motor going to the switch, the other going to the cord, then the ground wire. I would wire it the way your old motor was, could be that some models maybe were 2 speed and the other wire would be used for that. Either that or the wrong motor was in the box, it is the right part number (43576197 is Hoover number)
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replacement motor I purchase a replacement motor for a F5897-900 Hoover SteamVa Motor part # 43576197 or 27242051. The replacement motor has three electrical connectors + ground were as the orginal has two electrical connectors + ground. Do I ingnore the the thrid connector and hook up the wires to the same connectors as the orginal or do I have to do some rewiring.


The manual only show one wire from the motor going to the switch, the other going to the cord, then the ground wire. I would wire it the way your old motor was, could be that some models maybe were 2 speed and the other wire would be used for that. ... Vacuums

Replacement motor I am undertaking the repair of an old dustbuster as a training exercise. ,The motor in my V2410 is Made by Johnson Electric but I cannot find reference to the numbers marked on it on the manufacturers website. Are you able to give me a model number for an equivalent replacement or the specifications of the original motor? Thanks, Gary.


... Black & Decker V2410 DustBuster Handheld Vacuum

Replacing the Oreck vacuum cleaner motor with a generic Ametek motor, the wiring terminal are different and I need an electric diagram


... Vacuums

Replacement electric motor for Bissell Pro Heat 2x Select carpet


Bissell proheat i can spray solution from the handle but it has no suction help ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My 20" Patton electric fan has stopped working. I use it for animal cooling and it operates in dusty conditions. I suspect that the motor is shot. Is it worthwhile to replace the motor and are motors even available?


You could just try to clean the motor out by taking it apart, and shining the shaft up. then put some motor oil/engine oil on the shaft. That will work 99% of the time. ... Vacuums

Where can I get a new power head motor replacement for SE series,original motor GS ELECTRIC 5570-02-1 in UK or Ireland,Thank you,Liam.


... Rainbow E series Canister Wet/Dry Vacuum

Where do you hook the clear hose that is in the compartment with the motor ? Second where the vacuum hose connects to the bag it keeps cutting in and out of power. I replaced the female cord to motor and still cuts out."no suction "


Would you care to tell us the make and model of the vacuum you're asking about? ... Vacuums

I replaced the motor in my Oreck vacuum and it runs much faster than it used to and is very noisy. The wiring diagram that I received with the motor was very hard to read so I don't know if I wired it correctly. I also was not able to hook up the dual head lamps. Thanks, Bob


Hello Bbrote,Please visit the link provided below and find your model and then click for schematic :http://www.hescoinc.com/vacuum_cleaner_parts/oreck.html ... Vacuums

Where can I get a new power head motor replacement for se seriesoriginal motor gs electric 5570-02-1 in uk or irelandthank youliam.


... Rainbow E series Canister Wet/Dry Vacuum

I have a kenmore 116.25615506 vac and I want to replace the connector on the power sweeper. I cannot figure out how to disassemble the "electric folding wand" to get the connector out


... Kenmore Vacuums

I have 2003 Coleman Westlake Pop Up Camper. I have electrical problem. Replace circuit breaker and ground fault. Went camping, everything running fine the all of the sudden all power cuts off. Breaker did not trip, ground fault is fine. What could be the problem ? Is my converter bad ??


... Vacuums

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

I have a Hinari Domestic Homebaker, Model HB174SS - 600W appliance. The machine does not have any electrical power. Do you think the motor has burnt out? If so can I get a replacement and how much would it cost? Is it cheaper to buy a new one? I look forward to hearing from you. Regards. John Garrett


If you have power to the outlet it is safe to say that the motor is burnt out unfortunately these types of products are what we call throw aways you use them and throw them they don't come with replacement parts. Thank you for using Fixya ... Vacuums

I bought a new motor for my Riccar 8850. The new motor has 3 wires and the old one has 2. Which color wire is the ground? (or, which color wire don't I need?)


The third wire is a hot wire that goes to the headlight. ... Riccar 8850 Vacuum

Bissell Powerwash Proheat. model 1698-j, 220-240v, 50/60Hz, 1200-1400w. Motor stopped suddenly (ident label specifies type Ametek 119464-02), supply inline fuse at motor ruptured, fuse replaced but motor sparks like an angle grinder at armature and blew replacement fuse. Where can I obtain a replacement carbon brush set for the motor. UK based


... Bissell Vacuums

Beater bar motor quit, now the main motor quit. Replaced the on/off switch. still nothing


See this causes and fix it. God bless youIf the vacuum cleaner motor doesn't run the on - off switch might be \012turned off or defective. Test the switch with an Ohm meter or continuity\012 checker. \012 If the vacuum ... Vacuums

Im looking to replace the motor mines when bad looking to replace the burn out motor


... Hoover F5906-900 Upright Steam Vacuum

Ordered a replacement motor for Hoover GUV garage utility vac L2310. It took months to receive. There are no installation instructions and the old motor was left with one of the dealers and lost. Any suggestions as to how to replace this motor.


... Hoover L2310 GUV Central System Vacuum

The pump motor in my Bissel Proheat 2x Plus seems to have failed. It was seized so I sprayed WD-40 in it and let it sit for 3 days. Now I can turn it by hand, but when plugged into the unit it still doesn't spin. Here's a picture: http://bbay.dreamhost.com/bissel_proheat_2x_plus/P1070021.JPG I wanted to take the motor out and hook it into another power source to see if I can get it going but it has 3 wires. I'm used to only 2 (+ and -). How can I hook the motor up to another power source,


... Bissell Vacuums

How to replace the motor brushes? When should the motor brushes be replaced? Where can I purchase motor brushes for Model 1500 Easy-flow?


... Easy Flo EF1500 Vacuum

Worn electrical motor brushes


... Vacuums

The top motor on my Nutone CV-750 quit working


... Broan-NuTone CV750 Central Vacuum

Beam Soft Touch handle electric harness replacement


Set the bottom part of the handle down(not the part that the screws go in)the contact board will fit into slots on the left side of thehandle half, the switch will go where the cutout is for it on the top, the plug is notched to fit at the lower fron ... Beam Industries Wet/Dry Auto Central System Vacuum

I have a clarke bench grinder model 1002. I have a light that I would like to attach into the wiring though the grinder wiring in it's base. The light has two wires, and the grinder has a ground that is grounded to the base, a black that goes to a switch then to the motor. The white goes directly to the motor. where would I have to splice in the two wires from the light? I have a switch that I would like to put in for the light on off also.


Attach the white wire on your lamp to the white wire on the grinder.\012Attache the black wire on your lamp to the black wire on the motor side of the switch.\012This will give the lamp power any time the grinder is turned on.\012Yo ... Vacuums

How do I replace the Eureka Boss 5841 motor and what is the cost for that replacement motor?


... Eureka 5841 Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0636 seconds