Having problems with your Vacuums ?
The rolling part on the beater bar isnt rolling
Could be a bad bearing in the brushroll or the drive belt is broken
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
The rolling part on the beater bar isnt rolling
Could be a bad bearing in the brushroll or the drive belt is broken ... Vacuums
I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile
... Eureka Smartvac 4870 Bagged Upright Vacuum
Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest
I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum
My dyson animal is hard to push on carpet - the beater bar is still operational. When I turn off the beater bar and run the vacuum on hardwood the beater bar stops moving, but it still ''rolls'' on the hardwood - it doesn't pull up like it used to. It also seems to not be picking up as well as it used to, although no blockages are present and the filter is clean.
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Motor Fried? Eureka 431BX Vacuuming, and then all of the sudden the motor just stopped. Well idk if it's called the motor; the beater bar still spun, it was just the fan that stopped spinning Here is the whole vacuum in pieces http://i28.photobucket.com/albums/c237/SirFafner/Vacuum001.jpg Bottom Part, beater bar already taken out [Functions Fine] http://i28.photobucket.com/albums/c237/SirFafner/Vacuum002.jpg White Wire connecting to the fan motor [Looks black, i think it's fried, and that's the
Funny you said that,I went today and bought a bissel at Wal-Mart.Sure hope it lasts longer then the Eureka did.I will probably try to take the other one back to the store if I can find the receipt.Thanks so much. ... Eureka 431BX Bagless Upright Vacuum
My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?
Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Need part for electrolux beater bar rug cleaner.
The hose on my Samsung 9048R is torn partly from the swivel base. The main problem is that the carpet attachment with the beater bar will not operate now. My brother checked the connectivity at both ends of the hose and there is juice at the bottom swivel part but at the other end of the hose where the carpet wand plugs in it is dead. is there any way to fix this? How does the wire go up through the hose? I have looked around on the internet and it would seem that the entire hose assembly is
... Samsung Quiet Storm 9048R Bagged Canister Vacuum
I have a Dyson 15 "the ball". The beater bar will only rotate if the vacuum is engaged and the handle at a high angle. The bar stops when I drop the handle to a lower position. The condition is repeatable. Can you provide part and repair instructions?
If air is leaking in somewhere, you will not have any suction.\015\012\015\012\015\012Also there are some possibilities that has to be checked to confirm the fault.The problem is minor but the possibilities are too much for this pa ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
I just bought a dirt devil, started to vaccum got caught on a rug, and now the beater bar isnt working
... Dirt Devil Vacuums
Beater bar won't roll easily after I replaced the belt
... Eureka 4700A Maxima Bagless Upright Vacuum
I have the eureka boss 4495 widetrack and the end piece of the beater bar broke off. I guess I put it back together wrong when I put a new belt on. Where can I get a replacement part and will it work do you think.
Call the Eureka people (1-800-282-2886) and describe to them what the beater bar thingy that you broke is. Ask them if you can order that unit--if you think you can install it. Otherwise, ask them where to the authorized repair person closest to yo ... Eureka 4495A Bagless Upright Vacuum
The motor in my Powermate (Kenmore Canister 116.27614700) is whining, high pitched, but still works. A local shop told me the motor is dying (the one in the Powermate that drives the beater bar) and would cost $150 for them to repair. The machine is only 1.5 years old and I paid $300...yikes. I think I can fix it but don't understand why the foam gasket that apparently wraps around the motor costs as much as the motor. This is assuming that part 32 (ks747156) is the foam I see glued to my cur
I think you are right! Buy the motor.....use the gasket from the old motor if you can cut it off clean and just glue it on the new one.\015\012\015\012The connectors are just brass blade connectors which you should be able to get at a Ho ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum
The Panasonic MC-V7515 has two belts. The local vacuum repair guy says he only has a part number for the drive belt, which is UB-9. How do I find a replacement for the other belt, the one which directly drives the beater bars? By the way, this vacuum has great suction, but otherwise is far inferior to my previous Panasonic vacuums. The cheaper models aren't a good buy--stick with the more expensive models.
... Panasonic MC-V7515 Bagged Upright Vacuum
Bad beater bar end bushing for eureka 5860--part number??
... Eureka 5860A Bagless Upright Cyclonic Vacuum
I sucked in part of a throw rug and now the beater bar will not turn.
Hi,\015\012\015\012Turn\015\012 your upright vacuum cleaner or the vacuum head upside down to check the\015\012 beater bar. It will be located at the front edge of the unit.\015\012\015\012Remove\015\012 the clips ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being
Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums
Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n
From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums
Hi. We have a Riccar N2100 vacuum cleaner, which has served us well for many, many years. I'd like to attempt a repair on this unit, and looking for advice and/or a parts diagram to proceed. The unit makes a groaning sound when shut off. The sound tapers off in pitch as the motor and beater bar come to a stop. The sound only happens when the vacuum cleaner is turned off in the normal upright position. The sound does not happen when the lower unit and main housing are both laying flat. I took
My son dropped the vacuum down the stairs and now the vacuum works but the front part of the vacuum does not drop back down when vacuuming any type of floor. It slowly drops and does not stay on the carpet. hope this makes sense. I have cleaned filters and suction seems strong at the small hose. the beater bar rotate very fast still.
May be part missing. this is unit has 5-year warranty.you can send to service. ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I had a shoelace get stuck in the beater bar. I turned it off, tipped it over and untangled the shoelace from the beater bar. When I plugged it back in the vacuum ran but the beater bar was not turning and there wasn't any suction. Is there a reset switch for the beater bar? Thank you for your help, Janet
Hi Janet. there is a small reset button on the outside of the head next to the brush that you can push to get it to start spinning again. ... Dyson Ball DC24 Bagless Upright Vacuum
I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely
The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums
I ran my vacuum against an area rug that has strings around it and a few strings got caught up in the beater bar. Now, the beater bar does not function- the motor runs but the beater bar does not seem to be operating. I removed the strings from the bar.
Hi,\015\012\015\012There is a switch next to the main power switch on the handle which turns the brushbar on and off. When the beater bar becomes obstructed as in your case, there is a safety feature which cuts power to the beater bar. Al ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Vacuum bar not rolling
Belt is busted . Need new belt . Vac comes with three additional belts. Ask your roomate belts he should have them somewhere. ... Eureka 5892AVZ Bagless Upright Cyclonic Vacuum
I have a dyson DC28 vacuum and the power button flashes on and off and the beater bar quit turning. I turned it over and found some string caught on the beater bar which I removed, but the beater bar still does'nt turn and the power button still flashes on and off. I hope you can give me a solution to this problem.
I had the same symptom with my wife's DC28. The problem was associated with the cam driven height adjustment mechanism. The beater bar must rock freely up and down when pressing on the tabs that the end cam lobes actuate. On ours I found hair and cru ... Dyson DC28 Animal Bagless Upright Vacuum