Having problems with your Vacuums ?

Installing a belt

\015 How do you change the belt? Lost the manual.\015

Answers :

1. Unplug the vacuum
2. Take the bottom cover over the brush off by removing the 3 screws
3. Switch the brush roll control lever to bare floor
4. Take the roller brush out
5. Put the belt around the small pulley from the motor
6. As you are putting the roller brush back in put the belt around the space on the roller brush - center the belt on that space - THE BELT WILL NOT BE TIGHT BUT THAT'S NORMAL
7. Reinstall the bottom cover with the 3 screws

THE BELT DOES NOT GO AROUND THE SILVER PULLEY CONNECTED TO THE BRUSH ROLL CONTROL LEVER
MAY I KNOW THE EXACT MODEL OF YOUR VACUUM?
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Install belt how do you install the belt on the rug rennovator attachment?


Old models have 2 star screws will need two people and two screw drivers to loosen, ( be gentle) ... Kirby Heritage II Vacuum

Belt installation How do you install a #5 replacement belt on the Dirt Devil upright vacuum cleaner?


One end of the belt will go over the motor drive shaft and the other end will slip over the roller brush. Also, you can find this belt at www.vacbelts.com. ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

I want to install a belt on the turbo power 2000 upright vacum cleaner , What do I have to do to install it. The old belt broke.


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=564997\015\012Generic problem for all Vacuums\015\012I want to install a\015\012Posted by mcpo on May 02, 2008 ... Vacuums

How do i install a belt for a turbo cyclonic upright hoover uh7005 i already bought 5 blets for this vacuum and three of them were burnt i have 2 more belts left and i want to be sure i am doing the installation properly.


... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Installing belt How to install a belt on Hoover upright vacuum


Here are the step by step instructions from the owners manual for your machine.\015\012\015\012\015\012Disconnect cleaner from electrical outlet.\015\012WARNING: Agitator brush roll can start suddenly. Unplug cleaner before turning it over.&nbs ... Hoover Windtunnel Supreme U5280-900 Upright Vacuum

My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.


The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums

Belt drive Not only do I need a PN for the drive belt on the Panasonic MC-V7395 Vacuum Cleaner, I've noticed that there are problems with the belt breaking. Can someone also explain the proper way to install the belt over and around the motor spindles and any other information that may help. Thank you.


Http://www.partstore.com/Model/Matsushita/Panasonic/MCV7395.aspx?SearchTerm=True ... Panasonic MC-V7395 Vacuum

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a


The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Changeing belt how do you install a new belt? I have an Eureka, The Boss, bagless, upright. The brush is hardly rotating. I think it could be the belt but i cannot open the vacumm to check it. How can I fix this?


... Vacuums

How to install the belt on U8188900. It has a cam on the electric motor where the belt gos and there is a center looks like a pully and the part where it fits on the brusher. How do you get the belt around the center pully?


... Hoover U8188-900 Bagless Upright Vacuum

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]


Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

What is the secret of installing the belt? When I start in the off position & turn it to the belt on position, the belt is not picked up. It appears that the hook is backwards.


Kirby has produced a good video that shows you step by step how to change your belt. They show the Sentria model but this procedure is the same for every Kirby model. You will notice in the video that they mention the numbers on the side of the brush ... Kirby Generation 3 Bagged Upright Vacuum

My oreck throws off and burns belts. i install a new belt and it runs fine, but as soon as i try to vacuum the carpet, it burns the belt.


... Oreck XL Ultra Bagged Upright Vacuum

Belts I have recently bought new belts and when I installed the green light only comes on sometimes and I can smell rubber burning. The last belt broke very quickly so I am assuming that when I put the vacuum back together I am doing something incorrectly. Can you help instruct me?


Recently received a kirby from mother in law and don't how to change the belts ... Kirby Ultimate G Bagged Upright Vacuum

I have a Hoover Vacuum Cleaner, Runabout Supreme, on which the belt has broken. I purchased a new belt, part number 38528-040. I need some instructions on how to install the replacement belt? Thank you. JBS


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=728341\015\012Generic problem for all Vacuums\015\012I have a Hoover Vacuum\015\012Posted by Jimbob48 o ... Hoover Elite U5061-900 Bagged Upright Vacuum

New Hoover belt nbr 385280-34 installed, belt still too loose.


There is no adjustment. As they wear they cut the groove in the roller deeper. Sure fix,and what Hoover will tell you to do is to replace the roller. If your like me though that isn't any good. so what I did was wind wax coated dental floss into the ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover very noisy after new belt installed.


What is the belt # you have installed (generic)? Yes, there are problems with using generic belts on Hoover Vacuums. If you have noise I would suspect the roller, and replace it. the cost is about $25 and is something that you can install. The newer ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I HAVE A BISSELL MODEL 7920-3 AND IT NEEDS A NEW BELT. I WANT TO KNOW WHERE TO GET A BELT AND HOW TO INSTALL IT. THANK YOU, GARRY


Check here for beltcheck here for how to and belt ... Vacuums

My vacumm keeps burning up belts i need to make sure the proper way to install new belt


Does it need a real good cleaning\015\012 and make sure nothing in stuck in it ... Panasonic MC-V7398 Upright Vacuum

Belt burned up (first time); installed new belt but that starts to burn also; approx. 2 years old


Sounds like the brush that the belt is supposed to turn is bound up tight. Need to remove the brush and clean all debris from it. Where you can get at the center rod for the brush, the rod that the brush spins around, clean the ends and add some WD ... Panasonic Vacuums

Replace belt on eureka big boss sweeper. Bought sweeper got it cheap and it needs a belt. So i don't have anything to go on to replace it. Seems like there is a pulley below and not sure how to install


... Eureka 5849A Boss Bagless Upright Cyclonic Vacuum

Brush is not moving...not sure if it's the belt...anyway to find out how the belt should be installed?


Most likely it is the belt. Check to see if the belt is broken or the teeth have worn off. Here is the belt you need and the manual:Dyson DC17 Belt and ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Change Belt i don't know how to install a new belt on the U4551-920


I couldn't understand the other response so I'll put my two cents worth out there.\015\012\015\012Lower the handle all the way, flip the vacuum over and use a flat screwdriver in the slots as shown to remove the beater bar cover. On the top cov ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0464 seconds